I have network printer in one segment and wanted to print to it from remote
computers across a router (2 hops away). The printer is attached to an Intel
EtherExpress Pro 100 box and is configured to use TCP/IP printing. I was
able to install the printer on a remote Windows 2000 server, but could
Ping the print server from the 2000 and from each router in between. Post
your results here.
- Original Message -
From: Amjad M. Afana <[EMAIL PROTECTED]>
Newsgroups: groupstudy.cisco
To: <[EMAIL PROTECTED]>
Sent: Sunday, September 03, 2000 9:00 PM
Subject: Printer
>
roupstudy.cisco
> To: <[EMAIL PROTECTED]>
> Sent: Sunday, September 03, 2000 9:00 PM
> Subject: Printer
>
>
> > I have network printer in one segment and wanted to print to it from
> remote
> > computers across a router (2 hops away). The printer is attached to a
Okay, you've got connectivity, but TCP/IP printing often involves port
numbers.
What is your printer model? Port assignments vary from manufacturer to
manufacturer. Apple LaserWriters configure differently than Xerox DocuPrint
printers. Check your documentation.
By far the easiest config
Thanks for your reply guys. Yes there is connectivity. This is how I was able to
add the printer port to Windows 2000 (TCP/IP Port). Anywasy The printer is an HP
Deskjet 970 ( I believe). I have also noticted the following:
router 2 has IOS V12 and router has IOS 11.x. Looks like each IOS has
. Yes there is connectivity. This is how I was
able to
> add the printer port to Windows 2000 (TCP/IP Port). Anywasy The printer is
an HP
> Deskjet 970 ( I believe). I have also noticted the following:
>
> router 2 has IOS V12 and router has IOS 11.x. Looks like each IOS has
> diffe
Also, can you browse to the server from a remote workstation?
"Amjad Afana" <[EMAIL PROTECTED]> wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> Thanks for your reply guys. Yes there is connectivity. This is how I was
able to
> add the printer por
Amjad,
MS's IP printing relies on LPR on the workstation/server and LPD on the
print server itself. When you install the printer, Windows will check for a
response from the printer on the LPD port - TCP 515. Make sure you're using
a valid queue name - usually 'raw'
Hi All,
I really have a problem. I have enabled NAT on the router. I am able to
reach all PCs but the printer. Here is the senario:
192.168.1.0192.168.3.0
Question for all you IBM printer gurus. I have the following small office
connected to my hospital.
HOSPITAL-AIRONET340OFFICE-AIRONET340---C1924IBM AFP
Printer.
Here is the problem. After about 15-30 minutes the printer is no longer
visible or pingable from the network
Is this a Network printer with a card or jet direct box?
-Original Message-
From: Zolla Zimmerman [mailto:[EMAIL PROTECTED]]
Sent: Tuesday, March 19, 2002 8:04 AM
To: [EMAIL PROTECTED]
Subject: NAT with printer [7:38781]
Hi All,
I really have a problem. I have enabled NAT on the
Yes. This is a network printer with a card.
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=38785&t=38781
--
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondi
What does your access list look like that controls what gets NAT'd to the
192.168.8.0 pool?
Is the printer excluded from this NAT list?
What is the default gateway of the printer?
Arjen
-Original Message-
From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]
Sent: March 19, 2002 9:
When you say that you cannot reach the printer, do you mean:
- you cannot see it from your JetAdmin?
- you cannot telnet to it?
- you cannot ping it?
- ?
Have you set the default gateway to Router2 on the printer?
Have you verified the correct subnet mask on
Hi,
I have excluded the printer from the NAT pool through access-list only. Here
is what I have for the configuration:
ip nat pool ippool 192.168.8.1 192.168.8.254 netmask 255.255.255.0
ip nat inside source list 7 pool ippool
access-list 7 permit 192.168.3.0 0.0.0.255
access-list 7 deny host
Hi
I can not ping, traceroute, add the printer.
Thanks
When you say that you cannot reach the printer, do you mean:
- you cannot see it from your JetAdmin?
- you cannot telnet to it?
- you cannot ping it?
- ?
Have you set the default gateway to Router2 on the printer?
Have you
The ACL is backwards.
Is the server running a routing engine?
-Original Message-
From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]
Sent: March 19, 2002 10:16 AM
To: [EMAIL PROTECTED]
Subject: RE: NAT with printer [7:38781]
Hi,
I have excluded the printer from the NAT pool through
What do you mean by routing engine? I can ping the server from the other
network. The server has routing information. Do I have to change the gateway
on the printer to point the router?
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=38798&
Is it possible for you to update the firmware on your card
-Original Message-
From: Zolla Zimmerman [mailto:[EMAIL PROTECTED]]
Sent: Tuesday, March 19, 2002 9:44 AM
To: [EMAIL PROTECTED]
Subject: RE: NAT with printer [7:38781]
Yes. This is a network printer with a card.
Message
: [EMAIL PROTECTED]
Subject: RE: NAT with printer [7:38781]
Yes. This is a network printer with a card.
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=38802&t=38781
--
FAQ, list archives, and subscription in
Have you disallowed the printer address with an acl for the pool?
Marc
Zolla Zimmerman wrote:
>
> Hi All,
>
> I really have a problem. I have enabled NAT on the router. I am able to
> reach all PCs but the printer. Here is the senario:
&
No. I can not do this.
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=38803&t=38781
--
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL P
No it is Lexmark printer. I do not know the printer has a card or a print
server.
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=38805&t=38781
--
FAQ, list archives, and subscription info: http://www.groupstudy.
Yes, change the default gateway of the printer to be router2.
And before you go too far with this NAT/printer thing, make sure that you
can ping the printer from its local network.
-Original Message-
From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]
Sent: March 19, 2002 10:34 AM
To
Yes, the printer needs to know where to send traffic that is not on the
local network.
Telnet into the printer from a computer on the local network, and setup it's
default gateway.
Ole
~
Ole Drews Jensen
Systems Network Manager
CCNP, MCSE, MCP+I
Well I would change your ACL--switch order of the lines. I would then
suggest you take a labtop and give it the ip address of the printer and plug
it in and see if you can recieve and send pings with the labtop. I always
test printer problems like this. Of course the printer must be offline for
I changed the gateway to point to the router and it worked.
Thanks everybody. I and my boss really appreciate everybodies help in this
matter.
Zolla
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=38819&t=38781
--
FAQ, list archi
You might want to check is the port is going into "errordisable" mode.
Usually when this happens, the switch is either set to or detecting
full-duplex, when in fact the printer is only working in half-duplex. That
could explain the reset when you log into the switch. I have seen this
This is related to the printer MAC address aged out of
the CAM table due to inactivity. We see a lot on our
servers. What we do is creating a ping script
(traffic) on the servers to ping the gateway. In your
case, you can do a continuous ping to the printer IP
from a workstation or server, say
Hi Guys
I have a strange problem.
I have to carry a printer a different location ( The PC connected to
printer is not moving , only printer)
The printer must be connected to RS 232 Port of the PC.
So I will have to carry RS232 signals through Cisco Router.
I mean PC connected to serial port of
well I don't understand your question...but it would seem tat console output
would be console output regardless... IF you are consoling in at 9600, then
the output device is your screen. If you hook a printer up to the console
at 96008n1, then the output would be through the ribbon, ont
My interpretation of the question may be incorrect but it sounds like your
looking to extend a RS-232 connection across your router network?
PC-> RS-232-> Router-> Net-> Router-> RS-232-> Printer
I assume in theory you could use STUN (serial tunneling), but throw in the
fac
Architect
CTS Professional Services - Atlanta
__
-Original Message-
From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]
Sent: Monday, April 15, 2002 5:04 AM
To: [EMAIL PROTECTED]
Subject: Connecting printer through Cisco Routers [7:41473]
Hi Guys
I have a strange
33 matches
Mail list logo