Have a 2948GL 3 and want to set up a vlan but it docs state that you have to
set up ISL . I don't want ISL enabled. is there a way to just create VLANS
like in other L3 switches? I don't want to make these routeable or anything
just L2 VLANS simple VLANS
ie. when I do a "int vlan 400" this wou
I have the same switch but haven't VLAN'd it yet. I will soon. This document
has great examples and should be what you need to get the idea and set it
up.
http://www.cisco.com/warp/public/473/29.html
"" 416South"" wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> Have a 2948GL 3 a
Configure bridge groups on the switch, and assign ports to the bridge groups
as required.
CM
- Original Message -
From: " 416South"
To:
Sent: Thursday, January 17, 2002 9:03 PM
Subject: VLAN's [7:32351]
> Have a 2948GL 3 and want to set up a vlan but it docs stat
thanks sam but this doesn't let you do it unless ISL is implemented ... this
is a tough one plus there is not vlan database with this version of IOS it's
12.07 .. any other ideas??
sam sneed wrote:
>
> I have the same switch but haven't VLAN'd it yet. I will soon.
> This document
> has great exa
VLAN in 2848L3 works like that
!
interface FastEthernet2
duplex half
speed 10
bridge-group 20 -> VLAN 20
bridge-group 20 spanning-disabled
!
interface FastEthernet3
duplex half
speed 10
bridge-group 20 -> VLAN 20
bridge-group 20 spanning-disabled
!
!
interface
route ip
Without the "route" statement, routing doesn't occur between other VLANs.
Finally, each interface needs to have VLAN membership. At the interface
config:
bridge group xx
Took me a while to get all that right
Best, G.
ject: VLAN's [7:32351]
>
>
> Have a
In your original post as seen below, you said that you didn't want to make
this
routeable between the vlans. But are you wanting to route the traffic
anywhere
else, cause if you aren't, then just put the following in under the port
config.
"switchport access vlan 1", and you can then put what eve
you
> require, doesn't happen:
>
> bridge xx protocol ieee
> bridge xx route ip
>
> Without the "route" statement, routing doesn't occur between
> other VLANs.
>
> Finally, each interface needs to have VLAN membership. At the
> interface
> config:
&
s
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=32476&t=32351
--
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
M
> To: [EMAIL PROTECTED]
> Subject: RE: VLAN's [7:32351]
>
>
> Thanks all,
>
> in George's description mentions that that your doing
> intervlan routing,
> would this BVI work without a IP address and if not is there
> a command to
> just provide L2
> VP OGC
>
> > -Original Message-
> > From: 416South [mailto:[EMAIL PROTECTED]]
> > Sent: Friday, January 18, 2002 6:12 AM
> > To: [EMAIL PROTECTED]
> > Subject: RE: VLAN's [7:32351]
> >
> >
> > Thanks all,
> >
> > in
l
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=32531&t=32351
--
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
12 matches
Mail list logo