After last week’s hiccup, I was concerned this afternoon about 4:15 when a
windstorm knocked off my power … again! Fortunately, after cooking dinner on
top of the wood stove in the living room, they restored power in under four
hours. It’s been an exciting winter.
So ...
The weekly Elecraft
Flawless performance from 5 a.m. this morning right through 10 p.m. this
evening when I shut down for the night. The ATU tracked the K3's RX frequency
perfectly and all across the bands
And never once initiated a tune on TX RF.
As of shutdown, I had just shy of 250 QSO's search & pounce only
Good Evening,
Here in Oregon the weather has returned to normal; incessant rain
showers with fog and periods of high wind. At my elevation the
precipitation switches to snow now and then to keep things interesting.
When snow level drops into the valleys is when things go a little
crazy. Afte
Please explain what you mean by "getting only a couple resistance
measurements"
Does that mean that only a couple are correct?
Or does it mean that you can only accomplish a couple resistance
measurements?
A resistance measurement of zero is a valid measurement, and generally
indicates a short
I am building the k1 kit and am getting only a couple resistance measurements
on the resistance check stage of the rf board part 1 on page 29. I have checked
every stage twice as well as soldering shorts. Any one have any thoughts?
__
El
On 2/15/2014 5:54 PM, Mike Lichtman wrote:
When using the auto notch, I find a diminished volume. Anyone else
noticing this? 73 Mike KF6KXG
I don't have a KX3, but when I use the notch on my K3, the overall audio
volume decreases ... as it should. My hearing aids will automatically
notch out
Hi Mike,
The mount was never developed because there were too many good
alternatives available elsewhere. This doesn't mean we won't market a
mobile mount, but I would say it's not really in our plan at this
time.
One of the best alternatives I've found can be seen here:
http://www.rammount.co
When using the auto notch, I find a diminished volume. Anyone else noticing
this? 73 Mike KF6KXG
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecr
Was the mobile mount for the KX3 ever sold or is it on the development
list? If available, how can I order one? I would like to adapt it as part of an
under shelf mount in my base station yet also be able to quickly take the xcvr
portable. 73 Mike KF6KXG
__
Carl,
Check your SignaLink configuration (see the SignaLink documentation) to
be certain it is set for Line output rather than Mic level output - you
should not have to set your soundcard level to the maximum.
Note on the K3, you must drive the audio sufficiently to produce 4 bars
solid on t
I’ve used a SignaLink SL-1+ for years with an Icom 756PROIII and a laptop.
After getting my K3 up and running I decided to try hooking up the SIgnaLink. I
bought the cable that connects it to the line in and line out and PTT
connectors of the K3. It seems to work OK except that there didn’t seem
Hi Phil,
I had my P3 on top of my K3 for about a year until I got the SVGA card and
added an additional monitor which is now suspended over the K3. There's no
heat build up problem but if the K3 bale is up then I guess the P3 could
slide a bit when pushing P3 buttons. I used some of that rubbery s
W3FPR wrote:
"So IMHO, you already have everything needed."
Agreed, Don. Thanks for the confirmation.
W4TV wrote:
"With the incessant calling of some stations one simply
can not rely of seeing a signal pop up on the P3 or some software based
panadapter."
Joe, you are correct. Thanks for remin
Jorge,
AFAIK, probably not. The frequency must be shifted from RX to TX, and
with QRQ in effect it is not possible to shift that fast. A K3 with
'chirp' on the ham bands would not be a nice thing to hear.
73,
Don W3FPR
On 2/15/2014 2:33 PM, Jorge Diez - CX6VM wrote:
I saw in the manual of
Jorge,
listen using RX B and transmit with RX/TX A with full QSK at QRQ speeds.
I am using macros inspired by ZL2IFB:
SPLIT
RT0;XT0;FR0;DV0;BW0040;SWT13;SWT13;UP4;SB1;BW0100;MN111;MP002;MN255;
UNSPLIT
SWT11;BW0040;SWT13;SWT13;FR0;SB0;RT0;XT0;LK0;LK$0;MN111;MP001;MN255;
73,
Martin, OK1RR
Dne
Hello
I saw in the manual of K3 that CW QRQ is "temporarily turned OFF" with
SPLIT.
Will be in the future any way to use it in SPLIT mode or is impossible?
I usually use SPLIT when running to pick up calls few Hz up and down, like
it instead of RIT because of the large knob of VFO A
7
Hmm. "I found my arms and wrist got tired when
having to access the knobs and controls when the
P3 sat on top of the K3": Good point, Jim -- I
don't like my knobs too high. The K2/100 atop the
relatively thin KAT100 works well in that regard.
I'll play with it when I get it!
73, Phil
On 2/1
I find that my hands use the knobs on the P3 far
more that the K3. I estimate the ratio of P3 to
K3 use is 4:1 respectively.
I operate 99.99% CW, so my input is based on
primarily CW operation.
I suggest you try it out for a few days, when you
are active on the air, in the side position an
In over five years of ownership I've never heard this birdie before so I don't
know whether it's new or I just missed it before.
The birdie is S9 on 7.067 MHz and tunes at a 6X rate in the negative direction.
It's definitely internal. Anyone else have this?
Wes N7WS
What software are you using for digital modes - see the configuration
examples in microHAM Router (Help | download documents) or on-line in
the MK II area at www.microHAM-USA.com/support.html.
When using MK II with a K3, the audio switching tab in microHAM Router
should be set as follows: "Voic
The solution is to move the MCU crystal frequency slightly so that the spur is
below 28.000. We're looking into this.
73,
Wayne
N6KR
On Feb 14, 2014, at 5:57 PM, ac...@aol.com wrote:
> I used to have a short birdie on my K3 on 28.004.00 after keyup, but now
> after my 1.58 Beta firmware upgra
If you aren't already familiar with it, get some solder wick. Radio
Shack and anywhere they sell solder normally has it. It's just finely
braided copper wire. Lay the end on a solder joint, heat it with the
iron and it wicks up excess solder so you can easily remove components
when you add the
Hi Guys,
i've taken a Microkeyer II with his cables for K3 ( the one with the rear jack
for mic ), i've been able to set-up everything for RTTY and CW, but i'm having
big problems with phone and PSK31/JT65 .
I've connected an condenser mic to the rear of MKII with the supplied RJ45
adapter , b
During field testing of the newest firmware for the K3, KPA500 and KAT500,
after a good exercise of it I was asked to post my observations and I did in a
previous email to the list. There have been a few tweaks and the latest field
test versions have been released as public Beta versions. They
I have a shelf above my K3 which would allow the P3 to sit flat. My rotor is
there now, but it could be moved. I have a P3 waiting for construction, but
the rotor and shelf have been there since I put # 1025 there in 2007 or
whatever with no ill effects.
Willis 'Cookie' Cooke, TDXS DX Chairm
There are air inlet vents over the PA area and an up-firing speaker on top.
I use an inexpensive Costco 3-tier"Seville Classics Bamboo + Steel" shoe
shelf. The K3 and keys are underneath and the P3 is about 1-1/2" above the
K3, centered.
This shelf is much more robust than its predecessor. It h
Phil,
Having the P3 on top of the K3 has worked fine here for many years
with no problems. Your equipment configuration is mostly a matter of
operating convenience.
73,
matt W6NIA
On Sat, 15 Feb 2014 08:06:10 -0800, you wrote:
>Thursday I ordered my K3 and P3. All the images I
>see show the P
Thursday I ordered my K3 and P3. All the images I
see show the P3 on either the right or left side
of the K3. But it seems having the P3 screen just
above the display of the K3 would be an easier way
to operate.
Is there any reason not to locate the P3 that way
(like vents in the K3, speaker
This offer for Sale looks very suspicious to me. DO NOT FOLLOW IT UP
The"english" is not quite right & the phone code 07031 is a high cost
premium rate phone code frequently used by scammers!
73 Ray G3XLG
-
Ray G3XLG
--
View this message in context:
http://elecraft.365791.n2.nabble.com/F
This appears to work very well. The KAT500 following the VFO on the K3 is a
tremendous improvement. I like it.
Would it be possible to make the ATU TUNE button work with the
KPA500/KAT500 as well? That, and maybe making the ANT button select
outputs on the KAT500 would pretty much make the K3/KP
Any unused heil icm mikes with pl2t boom for k2 or mh2 hand mics out there?
Looking for bargain. If you have a different kind of mic that will work with k2
and dont use make offer.
John WT5Y
__
Elecraft mailing list
Home: http://mailm
My K3-KPA-KAT works great with all three betas and a new Windows utility for
KPA. Two solid days and no retuning or faults when I get too into the mic.
Thanks Elecraft for all the great help and continuing support.
-
Chuck, KE9UW
--
View this message in context:
http://elecraft.365791.n2.n
Sean,
For a first time builder, I recommend you simply follow the instructions
in the manual. There are only a few components that require desoldering
when adding the options .
I would suggest that you add the Front Panel components for the KSB2
option while you have the Front Panel Board ope
When working split, is there any reason why I have to be able to
decode both the DX (or split station [i.e. W1AW/x]) and the calling
station?
It's not absolutely necessary but it makes working split - especially
in big pile-ups - much easier if one can tell where the target is
listening. With
Joel,
If you are using the E-MU 0204 between the computer and the K3, that
satisfies your desire to have something other than the default sound
card between the K3 and the computer. Just tell the computer to use the
on-board card for normal windows sounds and tell your digital modes
software
I started this email with another thought in mind. The more I typed, the
more I thought I may be wrong about what I was thinking.
First, let me emphatically state that I *know* the K3 will just let you
plug into a computer sound card - I get that. I like something between
my radio and computer
I have seen this before when the 2.5mm key line jack just needed pushed home.
Rx without the key line causes the front LEDs to flash.
--
View this message in context:
http://elecraft.365791.n2.nabble.com/XV-144-Overdrive-protection-tp7584207p7584272.html
Sent from the Elecraft mailing list arch
37 matches
Mail list logo