Although Elecraft has documented the response curves of their 5 and 8
pole roofing filters, I can't find any plots of their narrow DSP CW
filters, like the 50, 100, 150 or 200 hz filters. Does anyone have
Elecraft published plots of the narrow CW DSP filters, or has anyone use
a signal generator
I am using the relay contact in the TS-590S, not SG, but the amp us in TX
mode with nothing connected to the PA Key jack, which should not happen.
With nothing but RF in and out connected to the rear panel it goes into TX
mode when I select Operate.
73,
Mark
W7MLG
On Nov 15, 2015 10:29 PM, "Barry
Yeah I'd like to know too. My KIO3 was busted from the factory (line input
doesn't work)... If I'm gonna replace it, it might as well be with the new
KIO3B
Dr. William J. Schmidt - K9HZ J68HZ 8P6HK ZF2HZ PJ4/K9HZ VP5/K9HZ PJ2/K9HZ
Owner - Operator
Big Signal Ranch - K9ZC
Staunton, Illinois
Ow
Hi Mark
I can relate to what you are experiencing with the KPA500.
You do not mention which rig you are using to drive the KPA500 or how you
have the transmit switching configured.
I bought a new TS590SG some months ago and set it up using the solid state
switching which on the face of it is exa
12.8 is pretty low. I run my Yaesu FP-1030A linear supply at 14.7 V for
K3 and K2. By the time the DC gets to the inside of the K3, it's about
14.5 and higher voltages reduce TX IMD some, not that the K3 isn't
really low IMD to begin with.
Not all power supplies are created equal ... in a ho
Kevin - thanks for the early checkin on 40 meter CW tonight. When I checked in
this afternoon on 20 I was using my K3 and KPA500 at about 450 watts. Tonight
on 40 I fired up the ion-smasher: a SoftRock Ensemble RXTX, running a whopping
1 watt into an 88 foot long doublet at 45 feet.
73, Jim /
Hello Bob,
Oh, I would also like to know when the new DSP board (with improved audio) will
be available for K3 upgrade.
As an overseas user, it is better for me to order everything in one-go.
73
Johnny VR2XMC
寄件人︰ Robert Nobis
收件人︰ Elecraft Reflector
傳送日期︰ 2015年11月16日 (週一) 9:00 AM
主題︰
Thanks Don and all others who replied.
I have not previously run the KAT500 utility, so was unaware of its
capabilities. I have it installed now and I'm studying the facilities.
73,
Alan. G4GNX
-Original Message-
From: Don Wilhelm
Sent: Sunday, November 15, 2015 4:47 AM
To: Robert
I suggest you adjust the PS voltage to 14.0 to 14.5 in receive.
73
Bob, K4TAX
On 11/15/2015 6:54 PM, Paul Taenzer wrote:
The 'low battery' issue was the problem.
I tweaked the power supply voltage up to 12.8 or so and no more noise!
Thanks everyone for your assistance.
Is there an update on the availability of the KIO3B for the K3? The last I
heard was available before the end of this year.
Thanks and 73,
Bob - N7RJN
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Hel
The 'low battery' issue was the problem.
I tweaked the power supply voltage up to 12.8 or so and no more noise!
Thanks everyone for your assistance.
73s
de Paul VA3LX
Paul Taenzer
ptaen...@gmail.com
613-385-1226
On Sun, Nov 15, 2015 at 5:38 PM, Paul Taenzer wrote:
> One more thing I just no
Mark;
Recheck the ribbon cable connections in the amplifier. This sounds like a
connector
is off, either to a side or more likely one complete row of pins is off. My
suspicion
is the 14-pin cable going to the front panel, but it could be the larger cable
going
to the IO board. You also might tr
I went back and reviewed the KAT500 command set and it doesn't look like
this is possible because the serial protocol does not have a way to
communicate split status. I've been knee deep in the KPA500 serial protocol
(with great results thanks to Jack W6FB) and thought they may have some high
leve
I doubt the KX3 would pass the required frequency stability requirements
for MS-DMT M110A modem software, even with very careful temperature
calibration.
73, Bob, WB4SON
On Sat, Nov 14, 2015 at 2:37 PM, Bill Frantz wrote:
> One of the items on my future projects list is a small box which would
Mark —
There may be some non-anecdotal data about this, but just from my
experience having 35 watts in and 400 out is not typical. On most bands I
run about 23 - 25 in for 500+ out, using a K3 as the driver.
Ted, KN1CBR
>--
>
>Message: 20
>Date: Sun, 15 Nov 2015 1
This is the 5th K3 I have built. Nonsmoker; in Mint, Like New condition. I
built this K3 on 06/15/2013.
When I build K3s I treat every pin with Caig DeOxit ProGold solution to
prevent intermittent contacts and pin oxidation.
It has been my primary rig and has never had any issues.
Two new
Apparently yes. However, I'm using the KAT500 serial port to communicate
frequency to the KAT500 via logging software (DXLabs), not auxBus, since the
radio is not a K3/S.
73,
Cliff K3LL
-Original Message-
From: Cady, Fred [mailto:fc...@montana.edu]
Sent: Sunday, November 15, 2015 2:28
The Elecraft SSB Net meets every Sunday at 18:00z (UTC) on 14.303.5 unless
otherwise
specified. The Net today had 24 check-ins (listed below). Thanks to Eric
WB9JNZ and
Jim W4RKS for help with relays.
73
John, N6JW
NC0JW JIM CO KX3 1356
W4RKS JIM TX K3 3
Well the cat is out of the bag. I did not intend to publicize this
until next week. General orders will not be taken until then, so if
you are not one of the seven I intended to receive this - you can relax.
I will open up orders on Nov. 23 taken in order of e-mail sent after
utc and of
One more thing I just noticed.
Sometimes (I can't figure out the pattern) the bottom line on the K3
display says low battery.
I'm not sure what that could be referring to.
Perhaps it's related to the mic noise??
TNX
Paul
VA3LX
Paul Taenzer
ptaen...@gmail.com
613-385-1226
On Sun, Nov 15, 2015
Thanks for you quick response!
Unfortunately that didn't seem to do the trick.
The speakers are not on (speakers + phone = no) and I tried turning the
monitor gain to zero.
Still no joy.
Other thoughts?
TNX agn,
Paul
VA3LX
Paul Taenzer
ptaen...@gmail.com
613-385-1226
On Sun, Nov 15, 2015 at
Yep - I'm aware of the K2 difference on the higher bands. I'm running V4
RC3, and it definitely does not correct the change on the higher bands.
I've not tried the earlier V4 version or any V3 version with the K2, so
can't shed any light on when things might have gone bad. I'm also using
LPB-2 a
Are you asking for the KAT500 to choose two different tuning solutions when
operating split? At present it chooses the VFO B frequency for its solution
according to:
MCU 4.83 / DSP 2.82, 2-8-2014
* FSK-D (RTTY) POWER-CONTROL BUG FIX: Power output can now be increased while
in transmit mode wh
Try it on a dummy load. If it changes then it is a radio problem. If it
doesn't then it's external.
If you have used the radio with CAT control, sometimes the software
application will not close and exit correctly and will leave "crud" or
fragmented data in the radio and there's no telling wh
Antenna issues specific to the OP aside, there is a valid reason to have the
KAT500 recognize split and inhibit retuning/recall.
The need for this functionality is very apparent when running split on 40m
SSB when the DX is below 7.1 MHz and listening up much higher than 5KHz for
anyone using a nar
> "Paul" == Paul Taenzer writes:
Paul> I recently developed a high pitched tone and seemingly random
Paul> noise when
Paul> keying the mic with either PTT or VOX
Paul> The noise goes away when the mic gain is set to zero. Changing
Paul> from the
Paul> Yamaha CM500
Paul,
Do you have the monitor gain up *and* have SPKR+Phones selected in the
menu? If so, the monitor sound from the speaker will be picked up by
the microphone and result in 'squeals'.
73,
Don W3FPR
On 11/15/2015 4:36 PM, Paul Taenzer wrote:
I recently developed a high pitched tone and se
I have finally gotten a breather from building transverters so
announcing a special order opportunity for those who wrote me
directly indicating an interest in purchasing the "W6PQL" 80w 2m Linear Amp.
This is a pre-sales special offer (starting today) for priority
purchase of the amp which is
I recently developed a high pitched tone and seemingly random noise when
keying the mic with either PTT or VOX
The K3 has been set up and running brilliantly (as one would expect) for 5
years with no changes to the set up recently.
The noise goes away when the mic gain is set to zero. Changing fr
The only thing that comes to mind, Mark,
absent a failed component someplace, is
perhaps one of the ribbon cables is
incorrectly installed. Good luck!
73, Ken K3IU
~
On 11/15/2015 3:24 PM, Mark Goldberg wrote:
I will contact Elecraft tomorrow, but p
I will contact Elecraft tomorrow, but posting in case someone
recognizes the symptoms.
I just put together a new KPA500 kit. When I select Operate, the RX
through the amplifier is significantly attenuated, many 10s of dBs.
The amp will also amplify even with nothing connected to the PA Key
RCA jac
What else do you have connected to the K3, specifically the serial port.
Overly strong signals will general kick in a relay to protect the front end of
the receiver and not
enable the attenuator. Is it possible that something else is enabling the
attenuator, like maybe a command
from a computer
Sounds like you may have a strong AM broadcast signal that is
overwhelming the K3 input.
MW signals will be attenuated by the Low Pass Filter, but those signals
below 160m will not be.
The K3 does have some suppression of AM Broadcast band frequencies, but
it may not be sufficient in your case.
Don
I know that the preamp and attenuator settings are remembered per band.
However, if I am on 160M and turn the attenuator off, it turns itself
back on
within 2 seconds. If I am on 80M and I turn the preamp on, it will
turn itself off within a couple of seconds.
I'm trying to find an expl
Dennis,
The attenuator (and preamp too) setting is per band.
If you have the attenuator on for 160 meters, then leave that band, it
will still be set on when you return to 160 meters.
While switched to 160, turn the attenuator off - change to another band
and then go back to 160m - the attenu
Joe
Yes, I can turn the attenuator off once I'm on 160M, but within 2
seconds of turning it off
it will turn itself back on.
Dennis W1UE
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mai
On 11/15/2015 2:06 PM, Dennis wrote:
I have a situation where a K3 with the attenuator off, when
bandswitched to 160M, turns the attenuator on.
The K3 remembers preamp and attenuator status by band. If you want the
attenuator off on 160, turn it off before leaving the band.
73,
... Joe,
Try this:
http://www.ke7x.com/home/guide-to-the-k3/the-elecaft-p3-svga-and-tx-monitor
From: Elecraft on behalf of Jim Brown
Sent: Sunday, November 15, 2015 11:19 AM
To: elecraft@mailman.qth.net
Subject: Re: [Elecraft] Looking for more P3 Operating Infor
I have a situation where a K3 with the attenuator off, when bandswitched
to 160M, turns the
attenuator on. I know this is the correct behavior for the K3 if the Rx
signal level is in the range
of +13 to +20dBm. That signal level, by the way, is on the order of
S9+90dB! And, yes, you
would be
Good Morning,
Power just came back on after a night of stormy weather. After a
week of steady rainfall the shallow rooted Douglas fir are getting water
logged; wind gusts can easily knock them into power lines. Luckily the
power lines at elevation are buried so the outages are fewer. How
On Sat,11/14/2015 10:04 AM, Cady, Fred wrote:
the P3 chapter from the The Elecraft K3s and P3
I don't see this link.
73, Jim
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/
On Sat,11/14/2015 8:37 PM, Byron Peebles wrote:
I will put the antenna analyzer on it tomorrow and make sure it's
still solid after all this wind.
Other suggestions. First, put it on bypass and see what the SWR
indication is. If it's reasonable, go to MAN mode, force a tuning (put
K3 in TUN m
Getting pretty warm. I can feel it on the outside in the area.
Nothing is blown. Should I add some "heat-paste" in order to help the
heat to spread ??
72
Allan OZ8A
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo
The K2 changes the LO injection from high side to low side above 17m.
Early versions of NaP3 and PowerSDR/IF had an option box that allowed
the user to enter a frequency for K2 (and for K3) which reverses the
sidebands at a specified frequency, but later versions should do this
automatically a
The K2 changes the LO injection from high side to low side above 17m.
Early versions of NaP3 and PowerSDR/IF had an option box that allowed
the user to enter a frequency for K2 (and for K3) which reverses the
sidebands at a specified frequency, but later versions should do this
automatically a
If you use a computer to control your rig, most of them can speak
mode/freq..etc..
If you don't use a PC look around for some RASPBERRYPI software to speak the
mode/freq..etc. Something like this has probably been done.
Jerry Moore
CDXA, INDEXA, SKCC, Fists
AE4PB, K3S - S.N. 010324
http://www.q
After some instructional and encouraging words from Don Wilhelm, I used the
recommended solution to unsolder L20 and roll it back away from connector
P6. That worked just fine, thanks Don.
73
Dave, K8AX
__
Elecraft mailing list
Home: htt
NaP3 already includes the ability to set different offsets for CW and CW-R
and those offsets are used in conjunction with the global offset which
applies to all modes. To make it work for the upper bands, you'd need to be
able to specify a separate global offset value based on the band you're on.
48 matches
Mail list logo