displays - -. I've gone through all the settings
and they look correct. The PWR knob is fully clockwise,
I'm not in test mode, etc., etc. I've sent an email to Elecraft
but I thought I'd check here as well to see if anyone has
seen this behavior.
Thanks,
- Bill
KB1PXD
--
View this message
.
73
Arie PA3A
-Oorspronkelijk bericht-
Van: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] Namens KB1PXD
Verzonden: zondag 22 maart 2009 15:07
Aan: elecraft@mailman.qth.net
Onderwerp: [Elecraft] [K3] No Power Output
Hello everyone,
as of last
mode. Just a thought.
Dave W7AQK
- Original Message -
From: KB1PXD bill.kim...@gmail.com
To: elecraft@mailman.qth.net
Sent: Sunday, March 22, 2009 7:06 AM
Subject: [Elecraft] [K3] No Power Output
Hello everyone,
as of last evening, my K3 is no longer indicating any
power
Greetings,
I just purchased a new computer (with Vista) as my old computer finally
died. Is there driver support for the KUSB cable and if so, where can
I download them? I noticed that the Prolific web site mentioned something
about not supporting Vista.
Thanks,
- Bill
--
View this message
Never mind. It appears the Microsoft drivers are adequate. I've loaded
the drivers and I'm in the process of updating the K3 firmware.
- Bill
KB1PXD wrote:
Greetings,
I just purchased a new computer (with Vista) as my old computer finally
died. Is there driver support for the KUSB
Greetings everyone,
I just noticed some odd behavior with IF DSP that I hadn't noticed
up until now. I'm not sure if I inadvertently changed a setting to
cause this behavior or not:
When I activate IF DSP, (VFO B / any setting) my S-meter goes to zero
whether I'm locked on to a signal or not.
Greetings,
I'm currently seeing a consistent S5 for noise level on 20m with the
pre-amp activated. It drops to S3 with the pre-amp disabled. This
reading was taken at noon time on the east coast. Does this sound
reasonable based on current conditions, or do you think I'm experiencing
IF, using only DSP, using both, etc.)
Thanks,
- Bill
Vic K2VCO wrote:
KB1PXD wrote:
Greetings,
I'm currently seeing a consistent S5 for noise level on 20m with the
pre-amp activated. It drops to S3 with the pre-amp disabled. This
reading was taken at noon time on the east coast. Does
Greetings,
I just picked up a new Heil Pro-Set PLUS headset for my K3 and
I've been trying to get the VOX settings adjusted appropriately. Keep
in mind that my shack is my bedroom which is very quiet. The MIC
is connected via the rear 1/8 mic/phone connectors. The following
settings have been
I forgot the following settings:
MIC GAIN = 40 (had to set higher for Heil versus stock mic)
Compression = 10
- Bill
KB1PXD wrote:
Greetings,
I just picked up a new Heil Pro-Set PLUS headset for my K3 and
I've been trying to get the VOX settings adjusted appropriately. Keep
in mind
otherwise. (I'm never used VOX before so I guess
I'm a little gun shy) Also, what element would you recommend? I'm
pretty much an exclusive DX operator.
Thanks,
- Bill
kb1pxd
--
View this message in context:
http://n2.nabble.com/Heil-Proset-Quiet-Phone-tp530729p530729.html
Sent from
BTW, I'm not locked down to the Quiet Phones. If someone thinks
the regular Proset phones are a better value, I'm completely open
to suggestions. These will be used exclusively in my shack which
is pretty quiet to begin with.
Thanks,
- Bill
KB1PXD wrote:
I'm thinking about swinging
Can anyone tell me if the K3 shipment via UPS requires
signature?
- Bill
--
View this message in context:
http://n2.nabble.com/K3-delivery-require-signature--tp527125p527125.html
Sent from the Elecraft mailing list archive at Nabble.com.
___
My wife just contacted UPS and they stated that no signature
would be required. I guess if you lived in an apartment or something,
the wouldn't leave the package without signature.
- Bill
KB1PXD wrote:
Can anyone tell me if the K3 shipment via UPS requires
signature?
- Bill
Greetings everyone,
I just received my K3 this afternoon. I'm using the stock Elecraft
microphone.
Can someone please provide me with some decent microphone settings to
get started? (ALC, CMP, Monitor, etc.) I have no idea what to set these
to and I was hoping that some of you have already
Greetings everyone,
I'll be receiving my K3 tomorrow afternoon and I had a question in regards
to cabling for firmware updates. I ordered the KUSB as I don't have a
serial
port on my laptop. Does the KUSB adapter include a cable and if not, what
kind of cable will I need? (standard
] On Behalf Of KB1PXD
Sent: Sunday, July 13, 2008 3:30 PM
To: elecraft@mailman.qth.net
Subject: [Elecraft] KUSB question
Greetings everyone,
I'll be receiving my K3 tomorrow afternoon and I had a question in regards
to cabling for firmware updates. I ordered the KUSB as I don't have
,
- Bill
KB1PXD wrote:
Greetings,
My K3 will be shipped out any day now! (woo-hoo)
I've decided to pickup a Heil headset, but I'm not sure if I should
go with the Elecraft proset-k2, or just run out to HRO and grab
a proset-4, etc. Questions:
1.) If I decide to pick one up at at HRO
that's pinned out for Kenwood radios? (8-pin)
2.) Does the Elecraft proset-k2 come already wired for the K3 with
no soldering required?
** I'm trying to avoid any soldering if possible.
Any pros/cons of either of these choices?
Thanks!
Bill
kb1pxd
--
View this message in context:
http
would be negligible, then
I'll just stick with what I have.
Thanks!
- Bill, kb1pxd
--
View this message in context:
http://www.nabble.com/Microphone-recommendation--tp16824607p16824607.html
Sent from the Elecraft mailing list archive at Nabble.com
-in ATU in my TS-850 has difficulties
with
certain frequency ranges within a couple of bands. Should I go with the
built-in
K3 ATU, or remove that from my order and just pickup an a decent external
LDG tuner? Any advice would be greatly appreciated.
Thanks!
- Bill, kb1pxd
--
View this message
Does anyone know if there's a Rigblaster or Signalink product
that supports the K3? I'm looking for a plug n' play canned solution
to support the digital modes.
Thanks,
- Bill, KB1PXD
--
View this message in context:
http://www.nabble.com/Rigblaster-Signalink-for-K3--tp16236271p16236271.html
, G4AON
K3/100 #80
Does anyone know if there's a Rigblaster or Signalink product
that supports the K3? I'm looking for a plug n' play canned solution
to support the digital modes.
Thanks,
- Bill, KB1PXD
___
Elecraft mailing
Thanks Simon. I couldn't have said it better myself.
Those my sentiments exactly.
- Bill
Simon Brown (HB9DRV) wrote:
The nice thing about an 'all-in-one' solution:
1) Just one USB cable connected to your radio.
2) Very high quality soundcard.
3) Winkeyer built-in.
4) Extra COM
:
SignaLink USB.
Simon Brown, HB9DRV
--
From: KB1PXD [EMAIL PROTECTED]
I too plan to use DM780 but have no interest in controlling
the K3 (changing freq., etc.) from HRD. I'm looking for the
simplest solution to support PSK31
,
- Bill
kb1pxd
--
View this message in context:
http://www.nabble.com/Is-the-K3-shipping-estimate-really-accurate--tp16037721p16037721.html
Sent from the Elecraft mailing list archive at Nabble.com.
___
Elecraft mailing list
Post to: Elecraft
back 4-6 months down the road
when my K3 is ready. I'll also be exploring used rigs as well. If anyone
has a K1 that they'd be interested in selling, please email me. I thought
about ordering one but I'm not confident enough to perform the assembly.
- Bill, KB1PXD
--
View this message in context
Also, if anyone is interested in selling their K2, please email me.
It'll probably be 1-2 weeks however until I'm ready to make the
purchase, but I'm definitely interested.
Thanks,
- Bill, KB1PXD
--
View this message in context:
http://www.nabble.com/Is-the-K3-shipping-estimate-really
28 matches
Mail list logo
