You aren't doing anything wrong. But, per Howard at Elecraft, it was so
bug ridden that it and the .33 version were removed from public sight.
Use the current version, you'll be fine until they have the staff time
to put into the P3-ware.
Once I went back to the 1.29, all was well with the
replace where the . with what the
-Original Message-
From: Hank P
Sent: Wednesday, April 01, 2015 11:11 AM
To: elecraft@mailman.qth.net
Subject: Re: [Elecraft] P3 artifacts
Couple questions:
1.Can some Guru tell me where WHAT the little spikes at +/- 300 and 600 cycles
Couple questions:
1.Can some Guru tell me where the little spikes at +/- 300 and 600 cycles
from the CW carrier (down about 40 dB) are when looking at a -73 dBm from
a XG1 or XG2 ?
2. I am curious what you typically see for the delta in dB between the
average baseline say at 10 msec
The P3 is hard to see, takes up space, costs money, doesn't do all that much
Okay, have I convinced you to sell me yours???!!! More seriously, I am
looking for a good used P3...! Thanks!
Jim, N3JT
--
View this message in context:
Will a Remote Rig or similar interface fit inside a P3? It would save a bit
of desk space which might be useful for portable/remote operations. I
believe the P3 is not itself remotable except by camera but that's a start.
Similar thinking for K3/0. These are at each end of the remote link
You can increase the waterfall sensitivity by adjusting the REF LVL to
place the noise right at the bottom of the spectrum display and then
increasing the SCALE setting. The same REF LVL and SCALE settings are
applied to both the spectrum and the waterfall displays. For further
details, see
I recently purchased a new P3/SVGA unit, and am using it with my K3 (serial #
6999). I have a few questions. First, when I engage the Marker function and
use it in the waterfall window, it comes up on the P3 screen, but not on the
external monitor (although it does work on the upper
On Tue,3/24/2015 12:44 PM, Hunter Ellington via Elecraft wrote:
Is there a sensitivity adjustment on the P3 that I need to play with?
All of your concerns are answered in the manual. The P3 is a very
powerful and versatile product, and the SVGA board increases its
capabilities. It's scan
Any information on possible future availability of a blank housing,
P3-size, in the vein of an EC2?
Would like to build a switching power supply into one to match the K-line
Any information is appreciated
John
__
Elecraft mailing list
I'd buy one ... actually two ... P3-sized housings. Better
still ... with speakers in Elecraft-branded housings. Yes,
they'd need to be expensive, but they'd be worth it.
Now, that would be a complete K-Line ! (:-))
73!
Ken - K0PP
On Mon, Mar 23, 2015 at 6:18 PM, John Klewer
Displayport or HDMI output from the P3.
Recently I've seen the advantage of
Blu-Ray quality video compared to
conventional DVD quality video with my HD
TV. For those like me, the difference is
more than a little and the definition is
incredibly life-like and very desirable.
I looked at my
After a disappointing experience with trying to buy one of these from this
list, will post one last time. If I can¹t
find one used, I guess I¹ll have to knuckle under and spring for the factory
prices.
Looking for a used, but like-new condition P3 with/without the P3SVGA video
card. Card
I have a nice P3 Panadapter for sale. It is 100% cosmetically and functions
100%. Has the SVGA option installed.
Also included is a 7 external display. Non smoking enviorment. Purchased
assembled. Have all manuals and paperwork.
$820 shipped. Paypal OK.
Steve . . . KK9W
Steve,
Did you receive my email? I've had trouble with gmail lately.
73
Josh W6XU
Sent from my mobile device
On Mar 16, 2015, at 7:16 AM, Steve kk9wra...@gmail.com wrote:
I have a nice P3 Panadapter for sale. It is 100% cosmetically and functions
100%. Has the SVGA option installed.
I worked K1N on RTTY using my K3 using the sub rx to find holes. No
P3, although a may get one. The method I use is to run a second MMTTY
window fed by the sub rx output on the audio right channel, an easy set
up in MMTTY. While it only gives a 3 or 4 khz spectrum, it is helpful,
so I was
I am in full agreement. I feel blind without my P3. At a glance I can
tell if the band is active or not. For example, last weekend with the
DX contest and the wide open 20m, the scope was almost solid in certain
spectrums.
I find that I use the subRX if I am getting bored on the 75m net and
Don ‹
I agree with Dave. I have both - the SubRX from the beginning and the P3
a year or so later. I have become addicted to the P3; but can¹t remember
using the SubRX for anything other than chasing DX in pileups. Even in
contests, where operating a significant split is usually a no-no, the
I had the same problem trying to work K1N. I don't have the
subreceiver, and trying to identify the station being worked
gets really hard as you switch between frequencies with the
REVerse button. It doesn't help that the tuning knob for the
pileup changes when you hold REV. Jack, W6FB
I would agree that the P3 should probably take priority over the
Subreceiver for a new buy, mostly due to the many different things it
can do for you. But... my experience this weekend trying to work E30FB
on 20 CW sure made me glad I had the Sub. I would never have worked them
using just the
Randy, I can do the same thing by holding REV and dialing around with VFO A.
Certainly not as convenient as having a subRX but it works. To make sure I
don’t accidentally lose the DX's frequency, I lock VFO A first.
Yes, I am amazed and shocked at the horrible operating practices I now see. I
You're preachin to da choir son. Fine job though.
K1N was awful for DQRM, lids and untrained idiots. 3G0ZC the next week
wasn't quite as bad, nor as rare. E30FB is rough here on the West Coast
due to lack of signal strength, conditions and the same crowds. You
can't hear, what isn't
There was also a problem with the BNC cable feeding the P3. I
experienced that and merely changed to a mil spec cable. That cured the
problem. No idea what caused the problem, but that cured it.
Bill W2BLC K-Line
__
Elecraft mailing
Hi Ted,
Do an archive search for the string:
SVGA ribbon cable
Review the posts and see if they bear any similarity to what you are now
experiencing. I think the gist of the thread was that placement of the
ribbon cable could be the cause of spurious spikes.
73,
Mike K2MK
Dauer, Edward
Just installed the SVGA option in the P3 and have an odd spike appearing
on the screen. Any help would be appreciated. Here are the symptoms:
The spike appears at 11.8 KHz above the VFO A frequency, and stays at that
distance as VFO A is tuned - that is, it moves as VFO A moves. It appears
on
Has a non Beta firmware update been released which minimizes the time for the
SVGA display to unfreeze between CQ’s during a contest?
This made it difficult to find/observe a clear channel in the waterfall between
CQ’s or contacts.
73,
Bud W3LL
w...@arrl.net
Don't see that here at 100 WPM, with or without QSK.
Here are the settings I have on my P3:
AVERAGE = 5
Waterfall Averaging = OFF
Peak = OFF
Using a 15 yr old VGA
Amateur Radio Operator
N5GE
On Mon, 02 Mar 2015 10:57:05 -0500, you wrote:
Has a non Beta firmware update been released which
Hi Bud,
I believe it's still beta. I'm running 1.35 on my P3 and 1.22 on my SVGA.
The freezes have been far fewer but it's still not 100%. However, the fact
that it is beta should not prevent you from using it. Beyond the occasional
freezes I have not seen any other problems with the firmware.
Apparently, you can add black, blue, white, and gold to the list of poor
cursor color choices. :-)
73,
Fred K6DGW
- Northern California Contest Club
- CU in the 50th Running of the Cal QSO Party 3-4 Oct 2015
- www.cqp.org
__
Elecraft
Me too. For me, blue and yellow are like night and day, but red, green,
brown, etc. are encompassed by a concept that I call groun. I would
like an option to make the TX cursor yellow.
30-odd years ago I used to have a 4-year old daughter standing by to
read resistor color codes to me, and
I realize that the discussion about split operations have beenenough to tan the
hides of every bovine used for McDonald'shamburgers for the next century, but I
would like to add my voteto what Fred mentioned, as I'm one of those 10% or
so of maleswho suffer from the inability to distinguish
On 19 Feb 2015, at 15:02, Phil Anderson aldenmcduf...@sunflower.com wrote:
Use the third button down and the right side of the P3 front panel - called
SPAN and widen what you are looking at. You can go as wide as 200 kHz. That
should do it.
I always use the P3 in Tracking mode, and
It would be helpful to have an option in the P3 utility that allows
saving or restoring a desired configuration the same way as is done
in the K3 utility.
Thanks,
Gary
KA1J
---
This email has been checked for viruses by Avast antivirus software.
http://www.avast.com
On Fri,2/20/2015 6:52 AM, John Bastin wrote:
I always use the P3 in Tracking mode,
You're missing a LOT by not using Fixed Tune and Averaging. Averaging
greatly reduces the noise, and Fixed Tune is needed so that averaging
continues to work as you tune the main VFO (the average resets when
A rousing second of Jim's fixed tune recommendation. I much anticipate its
availability in my PX3 as well.
Phil -- Sent from my iPhone 5S
On Feb 20, 2015, at 09:18, Jim Brown j...@audiosystemsgroup.com wrote:
On Fri,2/20/2015 6:52 AM, John Bastin wrote:
I always use the P3 in Tracking
jsdroys...@nc.rr.com writes:
Normally the P3 uses the VFO A frequency as its center, but when a
DX wants stations to call in very far above or below his own
frequency (a very wide split, as used by K1N recently) then I need
to learn how to tune the P3 away from the VFO A
Hi Julie,
Use the third button down and the right side of the P3 front panel -
called SPAN and widen what you are looking at. You can go as wide as 200
kHz. That should do it.
I like to use 100 to 50 kHz span so can see more detail on the P3
screen. I also added a 19 inch monitor so I could
Hi Julie,
It sounds like you prefer to leave your P3 in Tracking mode. The procedure
I'll describe works best if you have the P3 set to Fixed Tune mode. I have a
Fn button set to flip back and forth between Fixed Tune and Tracking but if
you don't you can easily access it from the Menu under
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help support this email list:
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help support this email list:
Normally the P3 uses the VFO A frequency as its center, but when a DX wants
stations to call in very far above or below his own frequency (a very wide
split, as used by K1N recently) then I need to learn how to tune the P3 away
from the VFO A frequency or else the pileup does not show on the
One observation:
I too have found the newest firmware to be much better. But I had it freeze
once and it didn't seem like it was ever coming back. I didn't time it but
it must have been stuck for at least 10 or 15 seconds. I tapped my foot
switch to briefly flick the K3 in and out of transmit,
I have been 'fighting' P3 freezes for a long time. Mostly mine have seemed to
be RFI related. I recently implemented most of Jim Brown's RFI prevention
suggestions, bonding, ferrite chokes, interconnected earth grounds, pin-1
problems, etc. and they have made a big difference. The freezing is not
Hi Carl,
I too am still experiencing occasional freezes. Typically 1 to 2 seconds in
length. I'm going to guess that the improvement is on the order of 95%. I
think the problem was described as the way in which the K3 tells the P3 that
it is coming out of transmit. You would think that if the
Hi Tighe,
I was able to repeatedly duplicate what you described. I think you found a
bug.
First, we should get the nomenclature correct. You don't mean VFO A Marker
you mean VFO A Cursor. And the problem only occurs in Tracking mode. And
the problem is not just caused by pressing the Spot
I apologize for taking more bandwidth, but I think this video is worth
sharing with other Elecraft users. It is very similar to another video I
posted a couple days ago, but this one is much better, and really
demonstrates the capabilities of the KRX3 and P3 in a huge pileup.
Essentially, it's
I confirmed the error. It's on the bug list, thanks.
Alan N1AL
On 02/08/2015 07:26 AM, Mike K2MK wrote:
Hi Tighe,
I was able to repeatedly duplicate what you described. I think you found a
bug.
First, we should get the nomenclature correct. You don't mean VFO A Marker
you mean VFO A
elecraft@mailman.qth.net
Sent: Tuesday, February 3, 2015 8:28 AM
Subject: Re: [Elecraft] P3 Beta SVGA Inop
No doubt this is being carefully read by Elecraft! I just want to add my
'bug' that the NB setting is not 'sticky' on the external display.
Otherwise, for me at least, the latest beta
Just noticed something odd with the latest P3 SVGA code (1.35/1.22).
Am split on 80m. Held the P3 button for Center and rotated the knob
so VFO A was closer to the left side of the screen then tapped the
button again. All was fine until I tapped Spot on the K3. Then the VFO
A marker on the
I've discovered when I adjust the span to its narrowest setting, the
outer sides of the screen in both the P3 and SVGA output fade with
the center being the brightest. When I'm looking at the perimeters
for weak signals this becomes somewhat problematic. I don't see it in
wider settings.
I reloaded the current non-beta version. Not having P3 working is not worth
playing with betas.
jim ab3cv
On Tue, Feb 3, 2015 at 1:52 AM, Gerald Manthey kc6...@gmail.com wrote:
I could not use the latest beta either. I had to go one beta back.
Gerald KC6CNN
On Feb 2, 2015 7:46 PM, Jim Miller
No doubt this is being carefully read by Elecraft! I just want to add my
'bug' that the NB setting is not 'sticky' on the external display.
Otherwise, for me at least, the latest beta appears to do its job.
Clearly, YMMV!
73 Stephen G4SJP
On 3 February 2015 at 13:19, Jim Miller
I still have a SVGA board for sale. Only used about 5 hours.Sold the P3
without it. P3SVGA P3 Video/FFT adapter
$230.00 PLUS $5.00 shipping to lower 48 States Keith, KV5J, XE3/K5ENS
nelasat@yahoo.comke...@kathyandkeith.mx
__
Decided to try the latest beta P3 firmware. All loaded including FPGA.
SVGA output is frozen and P3 is updating very slowly.
When I turn the SVGA display enable off the P3 behaves normally with a
proper update rate.
I've removed power from the P3 completely and restarted it with no
improvement.
Yes, I noticed the Step Span on mine seemed to reset after a power
cycle. It also appears to be set on a per band basis. Is there is a
way to set the REF LVL on a per band basis as well?
Mike
KI0HA
On 2/2/2015 04:31, ANDY NEHAN wrote:
I have noticed that the Span Step function (which I
I have noticed that the Span Step function (which I like) is not sticky - in
that every time I recycle my radio the feature, if set, is lost. That means I
have to go into the menu and reset it. Surely it would be better if the feature
was sticky like the other features??
What do you think PaulS
Andy Mike,
The Step Span in not remembered through a power cycle on my P3.
I have different REF LVL adjustments for each band on my P3 and they stay
that way through band changes and through power cycles.
I power my P3 from the K3 and I do not use the P3 power button. Could that
be a factor
I could not use the latest beta either. I had to go one beta back.
Gerald KC6CNN
On Feb 2, 2015 7:46 PM, Jim Miller j...@jtmiller.com wrote:
Decided to try the latest beta P3 firmware. All loaded including FPGA.
SVGA output is frozen and P3 is updating very slowly.
When I turn the SVGA
I just checked on a newly upgraded P3/SVGA and stepped span is remembered
through a power cycle. (I also checked the code just to be sure). If I turn
on stepped span and then power cycle the unit and press the SPAN key, the
span is in stepped mode. If I press a key that I assigned to stepped
I tried out the P3 NB feature during the 160 meter contest and maybe what I
tested it on was not impulse noise. I had a general noise level at S3 with
periodic 1 or 2 second bursts to S4 or S5 covering the entire band. The NB
feature did not eliminate these short duration noise bursts. I tried NB
New BETA firmware for the P3/SVGA is available for download from: P3/SVGA
BETA FIRMWARE
ftp://ftp.elecraft.com/P3/firmware/beta/P30135SVGA0122_BETA.zip
This new BETA release fixes a couple of issues found in the previous release
on 1/14/2015 and also adds a few features which carry over from
I remember talk about the possibility of using P3 buttons to send macro
commands to the K3. Is there a plan to make this possible?
I need more buttons!
Vic K2VCO /4X6GP
__
Elecraft mailing list
Home:
Since I often use the P3 for chasing DX in a pileup, I don't need the
empty space to the left 1/2 of the screen, or rarely, the right 1/2
of the screen when I have the Dx Tx freq in the center.
I'd like to see the P3 allow you to pin the DX Tx frequency to the
far side and use the entire
I do this in Fixed Track mode. I set the left edge just a little lower
than the DX QRG [VFO A in split mode], and then set the span to a little
wider than the pile-up which then occupies most of the width of the
screen. The VFO B [my TX QRG] cursor is then a snap to move to where I
think he
Hi Gary,
You'll want to use the center frequency shift feature. Hold the Center
button on the P3 to activate the function and turn the P3 knob until the DX
station (VFO A) is wherever you want it to be. It works in Fixed Tune mode
or Tracking mode.
73,
Mike K2MK
Gary Smith-2 wrote
Since I
Hi Tighe,
Thank you for detailed steps for reproducing the problem. I was able to
find the bug quickly and fix it for the next beta/release.
73,
Paul
--
View this message in context:
http://elecraft.365791.n2.nabble.com/P3-SVGA-WaterFall-Marker-Issue-tp7597230p7597269.html
Sent from
Just loaded the latest P3 Beta to get WaterFall Markers. Thanks for the
feature.
But... I noticed a curious behavior. Using the button on my P3 which
is programmed for WfallMkrs I noticed it's not controlling the SVGA
marker as it does the P3 display marker.
If I start with VFO A Marker
Two more observations.
If I turn the Waterfall Marker on and have it displaying on both P3 and
SVGA then tap the assigned button to turn the Waterfall Mark off, it
stops displaying on the P3 but on the SVGA where the marker is
displaying the marker stays with the VFO frequency. If I turn the
So I reloaded the P3 beta and went thru some tests as follows to try to
reproduce the external screen freeze:
took the svga option and then selected and tried each entry in sequence with no
problems. Did NOT try the ubmp, urst, usav as I had no usb device attached.
RX data window size OK
TX
Paul,
Glad to see this. I look forward to trying it as soon as I can do it.
Glad to see the fix for missing characters. If replay of keyboard input
is what I think it is,
that will be greatly appreciated. It is often needed.
Thanks for all,
Dick, n0ce
On 1/14/2015 7:01 PM, Paul Saffren N6HZ
Hi Andy,
Thank you for the report. Actually the bug is simply that the external
SVGA screen cannot be enabled after disabling. This is a genuine bug
and I have a fix already in place.
73,
Paul
Paul Saffren - N6HZ
Project Manager
Elecraft Inc.
831-763-4211 x122
www.elecraft.com
On
New BETA firmware for the P3/SVGA is available for download from: P3/SVGA
BETA FIRMWARE ftp://ftp.elecraft.com/P3/firmware/beta/
Release notes:
*MCU 01.34 / 1-8-2015*
* Added support for the SVGA noise blanker.
* Fixed a bug that occasionally caused a hesitation in resuming the display
Yes, I went back and looked and I had it turned up too high
Thank you
From: Alan n...@sonic.net
To: elecraft@mailman.qth.net
Sent: Thursday, January 8, 2015 8:36 PM
Subject: Re: [Elecraft] P3 and the Nose Blanker an observation
Also it is important to set the noise blanker level
I noticed something on the P3 and maybe it's a known thing.
I turned on my Flex-1500 that had been sitting idle for nearly a year and
noticedthat the display looked far sharper than the P3's display (Signals more
distinct).
Then I discovered what I was seeing... I had the noise blanker on the P3
Also it is important to set the noise blanker level to the minimum that
eliminates the noise.
Alan N1AL
On 01/08/2015 04:00 PM, Harry Yingst via Elecraft wrote:
I noticed something on the P3 and maybe it's a known thing.
I turned on my Flex-1500 that had been sitting idle for nearly a year
Hmmm ... don't know, but generally speaking anything monochrome works
for me. Ansel Adams photos look great to me, monochrome TV is fine too.
My wife tells me the P3 spectrum display background is deep blue,
which is just barely distinguishable for me from the black WF background
in
Fred,
Thanks for the fascinating description of your monochromacy.
I have never come across anyone with this, though did know the condition
existed.
As a photographer I am conscious of colours and had an amusing incident when I
had a faulty iPad display where the colours were posterised in
Interesting. Would a straight monochrome spectrum take care of all of this?
Al. W6LX
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post:
I may be the only Elecraft customer with this problem, monochromacy is
extremely rare [poor choice of both Mom and Dad :-)], but other forms of
defective color vision are much more common, mainly in males and most
hams are male. Consequently I'll reply to Alan on the list so everyone
can help
The subject line says it all. Anyone have any experience with this
combination? Does it work? Any problems? Comments/advice appreciated.
73,
Phil/VE1BVD
--
Phil Anne Irons
Sydney, Nova Scotia
__
Elecraft mailing list
Home:
Hi guys,
It wouldn't be hard to add an option to change the color of the VFO A
cursor. But I want to make sure I understand the problem.
By the way, I also have typical male red-green color blindness but I
have no trouble distinguishing the VFO A and VFO B cursors. There are
several types
I have a similar, but different, problem. I see more colors than Fred,
but I am red/green colorblind and my problem is telling the difference
between the VFO A and VFO B cursors. So Fred's solution would work for
me too.
On 4 Jan 2015 03:12, Fred Jensen wrote:
ALAN: Thank you for the
Technically, I can *see* all the colors ... I just can't name them. I
suspected something was amiss when all the crayons in the box had
different names and many looked the same to me. :-)
I have a couple of friends with P3's who are normies and they use the
monochrome WF too so it may not be
ALAN: Thank you for the monochrome WF option.
I don't want to get too greedy, and I may be the only Elecraft customer
with this problem, but during a contest [like RTTY RU on now], my wife
tells me the VFO A cursor is green. The spectrum in which it is
embedded is yellow. They look similar
-Original Message-
From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of
Tom Blahovici
Sent: Thursday, January 01, 2015 4:15 PM
To: Harry Yingst via Elecraft
Cc: Dauer, Edward
Subject: Re: [Elecraft] P3 and Other Windows Simultaneously
Hi
If you have a pc with a spare
...@mailman.qth.net] On Behalf Of Tom
Blahovici
Sent: Thursday, January 01, 2015 4:15 PM
To: Harry Yingst via Elecraft
Cc: Dauer, Edward
Subject: Re: [Elecraft] P3 and Other Windows Simultaneously
Hi
If you have a pc with a spare pci express slot and you are running a 64bit
operating system you can
Cc: Dauer, Edward
Subject: Re: [Elecraft] P3 and Other Windows Simultaneously
Hi
If you have a pc with a spare pci express slot and you are running a 64bit
operating system you can buy the avermedia hd game broadcaster and use it to
display a resizable window on your PC monitors.
If you
Subject: Re: [Elecraft] P3 - Keyboard
Message-ID: 54a39aa0.3040...@embarqmail.com
Content-Type: text/plain; charset=windows-1252; format=flowed
Tony,
FYI, I use an A/B switch to share a monitor between my P3 and Computer.
I seldom use the computer while operating.
If I do, I can still use the P3
, 2015 2:01 PM
To: elecraft@mailman.qth.net
Subject: [Elecraft] P3 and Other Windows Simultaneously
Or get a dual monitor - two screens side-by-side on a single mount - if
space allows. Several of the manufacturers make them.
Interestingly, a fellow at the Apple store here told me that the older Macs
From: Dauer, Edward eda...@law.du.edu
To: elecraft@mailman.qth.net elecraft@mailman.qth.net
Sent: Thursday, January 1, 2015 2:00 PM
Subject: [Elecraft] P3 and Other Windows Simultaneously
Or get a dual monitor - two screens side-by-side on a single mount - if
space allows
What is an Internet signal and how would that help?
Fred, AE6QL
-Original Message-
From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Dauer,
Edward
Sent: Thursday, January 01, 2015 11:01 AM
To: elecraft@mailman.qth.net
Subject: [Elecraft] P3 and Other Windows
01, 2015 5:58 PM
To: elecraft@mailman.qth.net
Subject: Re: [Elecraft] P3 and Other Windows Simultaneously
Hi Tony,
I found 3 immediate advantages with an external monitor. The first of course
was relief for my old eyes.
Next, on the P3 I preferred a span width of 10KHz on CW and RTTY and 50KHz
Hi Tony,
I found 3 immediate advantages with an external monitor. The first of course
was relief for my old eyes.
Next, on the P3 I preferred a span width of 10KHz on CW and RTTY and 50KHz
on SSB. On the external monitor I was able to jump to 20KHz and 100KHz.
The third benefit was the larger
Hi
If you have a pc with a spare pci express slot and you are running a 64bit
operating system you can buy the avermedia hd game broadcaster and use it to
display a resizable window on your PC monitors.
If you are really ambitious, you can then use VLC, to stream the video to
where you want.
To: elecraft@mailman.qth.net
Subject: [Elecraft] P3 and Other Windows Simultaneously
Or get a dual monitor - two screens side-by-side on a single mount - if
space allows. Several of the manufacturers make them.
Interestingly, a fellow at the Apple store here told me that the older
Macs
could have
There are monitors on the market that have PbP (Picture beside Picture)
capability built-in. I just acquired a Planar Systems IX-2850 4K 28
display which can display two, three or four inputs on-screen at once.
Since it's a 4K display when four inputs are shown each one still gets
1920x1080
PM
To: elecraft@mailman.qth.net
Subject: Re: [Elecraft] P3 - Keyboard
Hi Tony,
Nothing has changed, you cannot view a windows screen from your PC and the
enlarged P3 image from the SVGA board on your external monitor
simultaneously. You can, however, switch between multiple inputs on most
modern
: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of
Richard Fjeld
Sent: Wednesday, December 31, 2014 1:42 AM
To: elecraft@mailman.qth.net
Subject: Re: [Elecraft] P3 - Keyboard
Tony,
FYI, I use an A/B switch to share a monitor between my P3 and Computer.
I seldom use the computer while
I tried with the SVGA disabled and it did NOT occur -- at least in a few
minutes of testing. I suspect the same symptom might result from
multiple causes.
Since Wayne has indicated that it is on their list, I will present my
test parameters and leave it alone from here on. I am sure that they
Is there a quick fix eg a button press that will unlock the freeze? Waiting
10s for it to unfreeze on its own would send me round the bend.
73
David
G3UNA
No, I do not have the SVGA board and I see exactly what has been
described. Last night I saw it on voice several times for extended
Well, I guess I will chime in as well. I have spent some time this
morning trying at various speeds etc. and I cannot for the life of me
get my P3 to hang. I spent most of my operating time on CW and RTTY
using HRD latest beta, and DM780 and Navigator interface which has a
built in K1EL
1301 - 1400 of 4853 matches
Mail list logo