Was the issue resolved? Any update on the state of the investigation and
whether a firmware defect was confirmed?
Thanks and 73,
Andy, k3wyc
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help:
Bill,
Please post your results between the two KAT tuners. If it is a
software issue, perhaps going back one version might be on the table.
73, and thanks,
Dave (NK7Z)
https://www.nk7z.net
ARRL Volunteer Examiner
ARRL Technical Specialist, RFI
ARRL Asst. Director, NW Division, Technical
"Also, which should be obvious, the KAT500 is trained on each band and acts
appropriately with V1.75. Why it doesn't with V2.05 is currently a mystery. "
No, it was not obvious to me that you had trained all of each band. I had the
impression that you had trained only the FT8 frequencies in
Bill -
The good news is you're working with The Best.
Dick, K6KR, is The KAT500 Guru in my book. He's the one who steered me to
v2.05 when it was still Beta and together we figured out how to adjust it to
solve the very problem you're experiencing. As I said, v2.05 is even less
interested
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Bill Mader
Sent: Tuesday, August 23, 2022 3:33 PM
To: Elecraft E-mail Reflector
Subject: Re: [Elecraft] Problem with KAT500 firmware v. 2.05
While this may be an old thread, I have an input which could be int
While this may be an old thread, I have an input which could be interesting
to some. I recently noticed the KAT500 I am currently using had V1.75 of
the firmware installed. I use it with an IC-7610 and trained it on each HF
band, placed the MODE switch in MAN and tuned it for the FT8
I’ve been following this topic for a couple of days. Here are my observations:
I don’t use 80 metres much, mainly due to horrendous local noise. On Christmas
Eve, I wanted to join a Santa Claus net and checked the tuning solution for my
antenna (which is not very good for 80 metres) and it
I thought I had upgraded the firmware last month but somehow I must have
forgotten the KAT500. I just upgraded to the new firmware, and while I
think the tuning process is a bit slower than previous versions, I have
no problem tuning any of my wire antennae. My 160m and 80m antennae
still tune
, W0LEN
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Bob McGraw
Sent: Monday, January 03, 2022 11:24 AM
To: elecraft@mailman.qth.net
Subject: Re: [Elecraft] Problem with KAT500 firmware v. 2.05
Oh I intended to add, I run
Oh I intended to add, I run 20 watts as my TUNE power.
Also my other wire antenna, 240 ft center fed with 85 ft of 400 ohm
window line terminating to a hybrid 4:1 Guanella current balun and 1:1
Guanella current balun will match every frequency between 160M and 10M.
On 6M I bypass the tuner
"for my antennas, the new version found better matches than 1.75"
I realize now that could have been misunderstood. I intended - the new
firmware version found better matches than firmware version 1.75.
Anyway, good to hear that Dick is investigating. We had exchanged several
emails on the
On 1/2/2022 9:46 AM, Bart Campbell wrote:
Any ideas?
Where is it resonant? How high? What feedline?
73, Jim K9YC
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Hi Andy,
Thanks for your interest. Just FYI, Dick, K6KR, from Elecraft responded to
my initial email and is assisting me (on a Sunday during a holiday weekend
- one of the great things about Elecraft!). He had me send him traces from
both versions of the firmware. He has not had time to look
I have had issues with the new FW not finding solutions as well. I haven't
really investigated beyond discovering that the input attenuator is not the same
topography as the schematic and the resistor value isn't either. I don't know
whether this is a component failure or not. On a band or
14 matches
Mail list logo
