On Tuesday 12 August 2014 11:04:46 Marius Liebenberg did opine
And Gene did reply:
> I connected my spindle cmd signal to an abs component. When I set the
> speed for any output positive or negative, I get absolutely no output.
> Nor does any of the polarity indicators function.
> The setup uses a
Well I knew it's there cause I added it :)
Such a common problem.
Chris M
- Reply message -
From: "Marius Liebenberg"
To:
Subject: [Emc-users] No output from abs component
Date: Tue, Aug 12, 2014 8:50 AM
This is a symptom of complacency. Once you have done something in a
specific mann
This is a symptom of complacency. Once you have done something in a
specific manner you dont ever explore other possibilities. Like always
ordering steak because you now you like it.
On 2014-08-12 17:37, Chris Morley wrote:
> Are you using g 2.6?
> 2.6 has spindle abdolute output, In rpm and rp
On 2014-08-12 17:37, Chris Morley wrote:
> Are you using g 2.6?
> 2.6 has spindle abdolute output, In rpm and rps, iirc
No I am on master with this machine. I did not realize there was such an
output. I will have a look at it.
>
> Chris M
>
> - Reply message -
> From: "Marius Liebenberg"
Are you using g 2.6?
2.6 has spindle abdolute output, In rpm and rps, iirc
Chris M
- Reply message -
From: "Marius Liebenberg"
To: "Enhanced Machine Controller (EMC)"
Subject: [Emc-users] No output from abs component
Date: Tue, Aug 12, 2014 8:05 AM
I connected my spindle cmd signal
Its loaded, but, it's never going to work without being tied to a thread.
On 08/12/2014 11:14 AM, Marius Liebenberg wrote:
> On 2014-08-12 17:08, Sebastian Kuzminsky wrote:
>> On 8/12/14 9:04 AM, Marius Liebenberg wrote:
>>> I connected my spindle cmd signal to an abs component. When I set the
>>>
On 2014-08-12 17:23, andy pugh wrote:
> On 12 August 2014 16:04, Marius Liebenberg wrote:
>
>> The setup uses a 5i25 with a 7i76 so I had to load EMCMOT with the base
>> thread enabled as the abs component takes a float for input and output.
>> Any ideas?
> This doesn't make sense.
> abs can't ru
Isn't there a abs pin already integrated into the spindle cmd so you don't have
to use the abs component now?
On 08/12/2014 11:08 AM, Sebastian Kuzminsky wrote:
> On 8/12/14 9:04 AM, Marius Liebenberg wrote:
>> I connected my spindle cmd signal to an abs component. When I set the
>> speed for any
On 2014-08-12 17:20, Sebastian Kuzminsky wrote:
> On 8/12/14 9:14 AM, Marius Liebenberg wrote:
>> On 2014-08-12 17:08, Sebastian Kuzminsky wrote:
>>> Did you addf the abs function to the proper place in the proper thread?
>>>
>> I get an error if I do addf so I left it out. I can see the function
On 12 August 2014 16:04, Marius Liebenberg wrote:
> The setup uses a 5i25 with a 7i76 so I had to load EMCMOT with the base
> thread enabled as the abs component takes a float for input and output.
> Any ideas?
This doesn't make sense.
abs can't run in an integer-only base thread, nor is there a
On 8/12/14 9:14 AM, Marius Liebenberg wrote:
>
> On 2014-08-12 17:08, Sebastian Kuzminsky wrote:
>>
>> Did you addf the abs function to the proper place in the proper thread?
>>
> I get an error if I do addf so I left it out. I can see the function in
> the list of halshow though. Does that mean it
On 2014-08-12 17:13, Philipp Burch wrote:
> Hi Marius!
>
> On 12.08.2014 17:04, Marius Liebenberg wrote:
>> I connected my spindle cmd signal to an abs component. When I set the
>> speed for any output positive or negative, I get absolutely no output.
>> Nor does any of the polarity indicators fun
On 2014-08-12 17:08, Sebastian Kuzminsky wrote:
> On 8/12/14 9:04 AM, Marius Liebenberg wrote:
>> I connected my spindle cmd signal to an abs component. When I set the
>> speed for any output positive or negative, I get absolutely no output.
>> Nor does any of the polarity indicators function.
>>
Hi Marius!
On 12.08.2014 17:04, Marius Liebenberg wrote:
> I connected my spindle cmd signal to an abs component. When I set the
> speed for any output positive or negative, I get absolutely no output.
> Nor does any of the polarity indicators function.
> The setup uses a 5i25 with a 7i76 so I h
On 8/12/14 9:04 AM, Marius Liebenberg wrote:
> I connected my spindle cmd signal to an abs component. When I set the
> speed for any output positive or negative, I get absolutely no output.
> Nor does any of the polarity indicators function.
> The setup uses a 5i25 with a 7i76 so I had to load EMCM
I connected my spindle cmd signal to an abs component. When I set the
speed for any output positive or negative, I get absolutely no output.
Nor does any of the polarity indicators function.
The setup uses a 5i25 with a 7i76 so I had to load EMCMOT with the base
thread enabled as the abs compone
16 matches
Mail list logo