Hi,
I have the following problem:
Linuxcnc 2.9 pre xxx
MESA 7i90HD + 7i33 + 3 analog servo (ELMO ISP)
If I am running a code and I press ESC button to stop the execute, then
after pressing the button, the axes move again for approx. 15-20 mm.
The enable signal is not removed from the servo
I am grateful to everyone for helping me.
The solution axis.L.jogaccelfraction IN FLOAT
from Peter C. Wallace
Regards Csaba
___
Emc-users mailing list
Emc-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/emc-users
Dear Everyone,
I have a milling machine. To this machine I connected a WXHC-HB04 MPG. I
need help for the configuration.
I operate the machine through MESA 7i92+7i33 control card. (Linuxcnc 2.9
pre)
I set up everything. Also the MPG is operating. But if I operate it
through MPG, the axes are j
Hi All,
If You have Gildemaister lathe width EPL2 controller, please help me!
Can someone take a photo about the inside of EPL2 rack. It would be
could if the IC label (74HC02, HC04, ICM7556, etc.) would be visible.
Someone has repaired the machine before me, and it is possible that
someone
Hi Everebody,
I just bought a 7i92 card.
It works well but I don't know how can I remap the pin allocation. Right
now there is a G540x2D firmware uploaded on the card.
I would like to remap the pin allocation of the firmware.
Can you help me?
Regards,
Csaba
If I only configured the first port, there is no failure.
(First port on mainboard 0x378, I didn't take away the netmos9835 on the
mainboard.)
sorry my bad english
2016. 02. 14. 17:53 keltezéssel, Jon Elson írta:
> On 02/14/2016 04:10 AM, Horváth Csaba wrote:
>> Is it possible to
Is it possible to use netmos9835 (1LPT/2Serial port) card to Linuxcnc? I
would like to use it as a second port, but when I start the Linuxcnc
program, the program gives failure after giving of I/O setup and portadress.
For the Iscpci -v command I receive the following information:
portadress 0x1
*would like to realize the set-up of the CNC mill You can find it in the
attachement.*
*Please help me to select which MESA controller cards would be the best
for this function.*
*The computer will be PC. In this PC there are 2 qty PCI expansion ports
and 2 qty PCIE 1x slot. Also ethernet connecti
Hello Sebastian,
I try v2.6.6-1-g8679f71 and work fine!
Thanks!
2015.02.21. 2:58 keltezéssel, Sebastian Kuzminsky írta:
> I just pushed fixed this in the 2.6 branch, i think. Can you try
> v2.6.6-1-g8679f71 from git or from the buildbot?
>
---
Ezt az e-mailt az Avast víruskereső szoftver
I use the gantrykins.
2015.02.20. 18:37 keltezéssel, Sebastian Kuzminsky írta:
> Which kinematics are you using?
---
Ezt az e-mailt az Avast víruskereső szoftver átvizsgálta.
http://www.avast.com
--
Download BIRT iHub
Hi,
I updated from Linuxcnc 2.6.5 for 2.6.6.
I find with gantry style (XYZX) machine the following problem:
After homing of every axis it can't be switched over teleop mode. The
X-X axle connection doesn't come about during jog mode, but with MDI
function for G0 X1500 command the axes are movin
Hi Jon and Viesturs,
This maschine is flame cutting with semiautomatic Z high control.
The stepper motor is driven in all axis.
Where can I find the mistake?
PC latency time: 20287.
langvago.hal file:
loadrt gantrykins
setp gantrykins.joint-0 0
setp gantrykins.joint-1 1
setp gantrykins.joint-
Hi,
This is the first time I try to set the gantry mode on a machine (XYZX).
I cast a lot on the object related to these following errors, but I
couldn't find any solution.
I have 2 major problems with the gantry machine:
1. In World mode I get the error ""joint 2 following error". This error
a
13 matches
Mail list logo