collect2: error: ld returned 1 exit status
make: *** [/usr/share/linuxcnc/Makefile.modinc:125: userkfuncs.so] Error 1
This happens for the RIP and the debs installation.
Any suggestions please?
Regards
Marius
Ok got it sorted out. I had problems with my branch. I reloaded and
recompiled it and working is working now.
On 2023/10/10 13:05, Marius wrote:
On 2023/10/10 12:20, andy pugh wrote:
On Tue, 10 Oct 2023 at 10:48, Marius wrote:
It seems that halcompile has issues in master. it does not
On 2023/10/10 12:20, andy pugh wrote:
On Tue, 10 Oct 2023 at 10:48, Marius wrote:
It seems that halcompile has issues in master. it does not recognize a
.c file as legitimate and if you rename that to .comp it gets an error
ValueError: not enough values to unpack ( expected 2, got 1)
That
On 2023/10/10 12:20, andy pugh wrote:
On Tue, 10 Oct 2023 at 10:48, Marius wrote:
It seems that halcompile has issues in master. it does not recognize a
.c file as legitimate and if you rename that to .comp it gets an error
ValueError: not enough values to unpack ( expected 2, got 1
nuxcnc-dev/bin/halcompile", line 1366, in process
a, b = parse(filename)
File "/home/plasma/linuxcnc-dev/bin/halcompile", line 441, in parse
a, b = f.split("\n;;\n", 1)
ValueError: not enough values to unpack (expected 2, got 1)
On 2023/10/10 11:41, Marius wrote:
Hi
Hi
It seems that halcompile has issues in master. it does not recognize a
.c file as legitimate and if you rename that to .comp it gets an error
ValueError: not enough values to unpack ( expected 2, got 1)
Anyone know about this?
Regards
Marius
Hi
Is the server down? I cannot see the buildbot or the forum.
___
Emc-users mailing list
Emc-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/emc-users
And a problem with linuxcnc-doc-es. Takes over an hour to down load.
On 2023/08/08 10:02, Robin Szemeti via Emc-users wrote:
Works fine here ...
On Tue, 8 Aug 2023 at 08:59, Marius wrote:
Hi
I am trying to install and upgrade but all the files that are downloaded
from the linuxcnc.org
Definitely a problem with Linuxcnc-doc-en. I have been trying to update
from yesterday and every time we get stuck on that file. At least it is
one that I noticed.
On 2023/08/08 10:02, Robin Szemeti via Emc-users wrote:
Works fine here ...
On Tue, 8 Aug 2023 at 08:59, Marius wrote:
Hi
I
Hi
I am trying to install and upgrade but all the files that are downloaded
from the linuxcnc.org server seem to take forever and eventually time
out. Is there a problem or must I look elsewhere?
___
Emc-users mailing list
Emc-users@lists.sourcef
AM, Marius wrote:
Have a look at this forum thread where all the testing was done and the
problem discussed as it was encountered. Everything that you mentioned here was
tested and the results are not always as expected.
https://forum.linuxcnc.org/plasmac/49293-qtplasmac-with-fourth-axis
ular moves 25.4 times faster.
Todd Zuercher
P. Graham Dunn Inc.
630 Henry Street
Dalton, Ohio 44618
Phone: (330)828-2105ext. 2031
-Original Message-----
From: Marius
Sent: Friday, July 07, 2023 4:17 AM
To: emc-users@lists.sourceforge.net
Subject: Re: [Emc-users] [Emc-developers] Tra
4 Jul 2023 at 18:34, Marius wrote:
The problem seems to be that our trajectory planner lack the ability to
look ahead for any rotary axis. This means that a coordinated move that
includes a rotary move will be dysfunctional at best.
It's not as bad as that.
There is a 9-axis blending planner
On 2023/07/06 18:48, Chris Albertson wrote:
On Jul 6, 2023, at 9:22 AM, Roland Jollivet wrote:
The small 4-axis CNC machine,'Pocket Nc' uses LinuxCNC as far as I can
tell, and it seems to run just fine. Or does it?
Does this device move all four axes at the same time while cutting? Or doe
would
stand to benefit from this and other users that I have spoken to has
indicated that they would gladly contribute.
I would at least want to start a discussion around the idea.
Regards
Marius
___
Emc-users mailing list
Emc-users
Hi all,
@Phill, this question was asked on the forum. Can anyone shed some light
please?
Does anyone know how QTPlasmaC handles referencing when keep-z-motion = 1?
Regards
Marius
___
Emc-users mailing list
Emc-users@lists.sourceforge.net
https
2022-10-07 14:06, stjohn gold rašė:
Hi,
I need 2 stmbl drives. Does anyone have some they are not using or wish to
sell? Just tell me how much you want and I can arrange to get them picked
up and shipped to me. Send me mail and I will answer!
many thanks,
St.john
I would also be interested in
2022-09-12 04:18, Ed rašė:
I have a 5i25 card that needs to be used but late model PC's do not seem
to use PCI anymore. Does anyone know if the PCI-E to PCI adapters that
are on ebay and such will drive a 5i25?
TIA, Ed.
Yes, I can confirm they work.
__
Gene,
how about setting min and max limits to zero (or other initial value),
maybe also not enabling B drive?
This can be done in a bash script like:
halcmd unlinkp io-board-going-to-b-servo-drive.enable-pin
halcmd setp ini.4.min_limit 0
halcmd setp ini.4.max_limit 0
halcmd setp ini.b.min_limit
On 2022/04/16 08:55, Marius wrote:
On 2022/04/15 18:58, Andy Pugh wrote:
On 15 Apr 2022, at 12:52, Marius wrote:
Just wondering why is it not possible to have a standard three axis
trivkins setup with a possibility to slave a stepgen to any one of
the axis.
You can do that. In fact it
On 2022/04/14 18:58, Peter C. Wallace wrote:
I suspect that you are right. For the sake of time running out I
just slaved the X stepgen in the bit file. I am using a simple
trivkins with no slave axis defined. The only issue now is that
the DIR signal on the slave has to be inverted somehow.
Hi
Just wondering why is it not possible to have a standard three axis
trivkins setup with a possibility to slave a stepgen to any one of the axis.
So it is not part of the kinematics just slaved to the command signal of
any axis?
It is done in Mach3 and I have installed many machines that
On 2022/04/14 18:58, Peter C. Wallace wrote:
I suspect that you are right. For the sake of time running out I
just slaved the X stepgen in the bit file. I am using a simple
trivkins with no slave axis defined. The only issue now is that
the DIR signal on the slave has to be inverted somehow.
On 2022/04/14 18:51, Peter C. Wallace wrote:
On Thu, 14 Apr 2022, Marius wrote:
Date: Thu, 14 Apr 2022 18:42:53 +0200
From: Marius
Reply-To: "Enhanced Machine Controller (EMC)"
To: "Enhanced Machine Controller (EMC)"
Subject: Re: [Emc-users] Looking for 7i92 bit
On 2022/04/14 18:26, Peter C. Wallace wrote:
On Thu, 14 Apr 2022, Marius wrote:
Date: Thu, 14 Apr 2022 17:56:53 +0200
From: Marius
Reply-To: "Enhanced Machine Controller (EMC)"
To: "Enhanced Machine Controller (EMC)"
Subject: Re: [Emc-users] Looking for 7i92 bit
This what I done in the bit file
-- the X stepgen is slaved to pins 4 and 5
constant PinDesc : PinDescType :=(
-- Base func sec unit sec func sec pin -- external DB25
IOPortTag & x"00" & PWMTag & PWMAOutPin, -- I/O
00 PIN 1 Spindle DAC PWM
On 2022/04/14 17:25, Peter C. Wallace wrote:
I suspect that you are right. For the sake of time running out I just
slaved the X stepgen in the bit file. I am using a simple trivkins
with no slave axis defined. The only issue now is that the DIR signal
on the slave has to be inverted somehow
On 2022/04/14 16:35, Peter C. Wallace wrote:
On Thu, 14 Apr 2022, Marius wrote:
Date: Thu, 14 Apr 2022 16:18:43 +0200
From: Marius
Reply-To: "Enhanced Machine Controller (EMC)"
To: "Enhanced Machine Controller (EMC)"
Subject: Re: [Emc-users] Looking for 7i92 bit
Correct. It's not an issue. Just noted it. I looked at the source and it
does not assign a stepgen to the 16/17 pins of port 2. I might want to
change that for the next conversion where the Z axis will be used.
Did you setup the slave axis as X2?
It does but it deliberately sets it to stepgen
On 2022/04/13 18:52, Peter C. Wallace wrote:
On Wed, 13 Apr 2022, Marius wrote:
Date: Wed, 13 Apr 2022 18:40:15 +0200
From: Marius
Reply-To: "Enhanced Machine Controller (EMC)"
To: Peter C. Wallace
Subject: Re: [Emc-users] Looking for 7i92 bit file
I redid the c
Apr 2022, Marius wrote:
Date: Tue, 12 Apr 2022 16:22:37 +0200
From: Marius
Reply-To: "Enhanced Machine Controller (EMC)"
To: "Enhanced Machine Controller (EMC)"
Subject: Re: [Emc-users] Looking for 7i92 bit file
I attached a picture. Don't remember if that
on at all.
On 2022/04/12 16:35, Peter C. Wallace wrote:
On Tue, 12 Apr 2022, Marius wrote:
Date: Tue, 12 Apr 2022 16:22:37 +0200
From: Marius
Reply-To: "Enhanced Machine Controller (EMC)"
To: "Enhanced Machine Controller (EMC)"
Subject: Re: [Emc-users] Loo
wrote:
On Tue, 12 Apr 2022, Marius wrote:
Date: Tue, 12 Apr 2022 16:22:37 +0200
From: Marius
Reply-To: "Enhanced Machine Controller (EMC)"
To: "Enhanced Machine Controller (EMC)"
Subject: Re: [Emc-users] Looking for 7i92 bit file
I attached a picture. Don't rem
On 2022/04/13 16:44, Peter C. Wallace wrote:
On Wed, 13 Apr 2022, Marius wrote:
Date: Wed, 13 Apr 2022 13:16:06 +0200
From: Marius
Reply-To: "Enhanced Machine Controller (EMC)"
To: "Enhanced Machine Controller (EMC)"
Subject: Re: [Emc-users] Looking for 7i9
C. Wallace wrote:
On Tue, 12 Apr 2022, Marius wrote:
Date: Tue, 12 Apr 2022 16:22:37 +0200
From: Marius
Reply-To: "Enhanced Machine Controller (EMC)"
To: "Enhanced Machine Controller (EMC)"
Subject: Re: [Emc-users] Looking for 7i92 bit file
I attached a picture. Do
:
On Tue, 12 Apr 2022 at 13:48, Marius wrote:
The config I have to replicate is this.
Seems to be coming through blank.
--
___
Emc-users mailing list
Emc-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/emc-users
some numbers on the left side but they make no sense.
XSTEP - 2 : XDIR -3
X2STEP - 4 : X2DIR - 5
YSTEP - 6 : YDIR - 7
NO Z (or 16 and 17)
ASTEP - 8 : ADIR 9
On 2022/04/12 15:50, andy pugh wrote:
On Tue, 12 Apr 2022 at 13:48, Marius wrote:
The config I have to replicate is this.
Seems
Hi
I am looking for a bit file for the 7i92e that will replicate the
parallel port to suit a standard BOB. In particular the Greg Paxton BOB.
The config I have to replicate is this.
Motor pin allocations
Regards
Marius
___
Emc-users mailing
productId=0xeb93,
will continue in 0s
lsusb reports this:
Bus 001 Device 007: ID 10ce:eb70 Silicon Labs
The product ID is not the same. Could this be a problem?
Regards
Marius
___
Emc-users mailing list
Emc-users@lists.sourceforge.net
https
respectively.. it sets those positions but
doesn't then move anywhere else.
On Tue, Aug 31, 2021, 2:04 AM Marius wrote:
On 2021/08/31 03:25, Leonardo Marsaglia wrote:
Hi Marius,
Are you driving your A axis with steppers or servos? What are you
using
as
the physical home switch?
You c
On 2021/08/31 03:25, Leonardo Marsaglia wrote:
Hi Marius,
Are you driving your A axis with steppers or servos? What are you using as
the physical home switch?
You can always fool the homing sequence at least into some extent. I wanted
to use servos in open loop but that was incompatible with
Hi
I am trying to create my own homing sequence on the A axis in Gmoccapy.
Is there a way to set the "homed" signal to true once I have done my
sequence?
Regards
Marius
___
Emc-users mailing list
Emc-users@lists.sourceforge
I think I solved that problem in Emcoturn 220 integration and went even
further. I added a protection of lost steps with the sensor. Here is my
config:
https://drive.google.com/drive/folders/1tjU-i8v7iAPqDlRHX5l45pFpincPqneS?usp=sharing
Hope this helps.
On 2021-03-01 06:21, Feral Engineer wrot
On 2020/09/03 10:06, andy pugh wrote:
On Thu, 3 Sep 2020 at 02:27, James Reed wrote:
Evidently, I'm not accustomed to the usual NPN proxes. We have some NPN
devices at work that have the collector tied to supply, with the emitter as the
output.
I suspect that the nomenclature is mis-appli
On 2020/09/02 20:34, Peter C. Wallace wrote:
On Wed, 2 Sep 2020, Marius wrote:
Date: Wed, 2 Sep 2020 20:07:40 +0200
From: Marius
Reply-To: "Enhanced Machine Controller (EMC)"
To: emc-users@lists.sourceforge.net
Subject: [Emc-users] 7i76 input with NPN NO
I am using a 7i76e
I am using a 7i76e which has sinking inputs. The machine was built using
NPN N/O proximity sensors. Am I correct in saying that I have to pull
the sensor output up with a resistor and then connect that junction to
the 7i76 input?
Regards
Marius
some development and
testing later
On Tue, Sep 1, 2020 at 8:23 PM Frank Tkalcevic
wrote:
I use VMWare player on Windows 10 without any issues.
-Original Message-
From: Marius [mailto:mar...@mastercut.co.za]
Sent: Wednesday, 2 September 2020 1:58 AM
To: emc-users@lists.sourceforg
Hi Rafael
Thanks for the feedback
On 2020/09/02 05:24, Rafael Skodlar wrote:
Hi Marius,
On 9/1/20 9:29 AM, Marius wrote:
Hi Todd
I just need to run a simuation to show some GUI's and fucntionality.
Thanks I will try VitrualBox.
My test with 2 different version of LinuxCNC in Virtu
se VMs are incapable of realtime.
I have only used Virtualbox myself and it works fine for simulations.
Todd Zuercher
P. Graham Dunn Inc.
630 Henry Street
Dalton, Ohio 44618
Phone: (330)828-2105ext. 2031
-Original Message-----
From: Marius
Sent: Tuesday, September 01, 2020 11:58 AM
To:
What would the VM users say that the best free version of VM would be to
run LinuxCnc in. I have to do a demo for a client and I dont have a
working machine to do so with.
Regards
Marius
___
Emc-users mailing list
Emc-users@lists.sourceforge.net
I am going to get one and report back
On 2020/07/23 17:41, Dave Matthews wrote:
A link to a video for this thing showed up in my facecrap feed. It
looks like a UC-100 only for LinuxCNC 2.9. They are demoing on a Pi
4. Has anyone got any experience with the Linumeric-LPT v1? Price
and orderin
I am making some latency-tests on different PCs. I would like to publish
some results..
I am trying to log-in to
http://wiki.linuxcnc.org/cgi-bin/wiki.pl?Latency-Test, while I forgot
the secret name of our mascot.
___
Emc-users mailing list
Emc-
Don't forget the simplest and most economic all-in-one solution like
Mesa 7i96
https://mesaus.com/product-category/ethernet-cards/
___
Emc-users mailing list
Emc-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/emc-users
On 2019/12/04 18:41, Mark Johnsen wrote:
Marius,
You need to see what kind of encoder the Yaskawa motor has on it. I recall
many of them were serial w/ a proprietary Yaskawa protocol, which would
make it hard to run the encoder directly back to the mesa.
Possibly, the servo pack has an
controller. My
question is: Is it ok to use the STEP/DIR feature of this servo pack
with encoder feedback to LCNC or should I go the Analog route and redo
the complete system making use of the 7I97.
Regards
Marius
___
Emc-users mailing list
Emc-users
://lists.sourceforge.net/lists/listinfo/emc-users
--
Regards / Groete
Marius D. Liebenberg
082 698 3251
___
Emc-users mailing list
Emc-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/emc-users
On 9/4/2019 9:09 PM, Peter C. Wallace wrote:
On Wed, 4 Sep 2019, Marius Liebenberg wrote:
Date: Wed, 4 Sep 2019 21:03:10 +0200
From: Marius Liebenberg
Reply-To: "Enhanced Machine Controller (EMC)"
To: "Enhanced Machine Controller (EMC)"
Subject: [Emc-users] Mesa
Hi all
Does anyone know of a document or a description somewhere that explains
the contents, structure and possibilities of the Mesa PIN file?
--
Regards / Groete
Marius D. Liebenberg
082 698 3251
___
Emc-users mailing list
Emc-users
ogic;
TP : out std_logic_vector(1 downto 0);
OPTS : in std_logic_vector(1 downto 0)
);
end TopEthernetHostMot2;
Any advice please?
--
Regards / Groete
Marius D. Liebenberg
082 698 3251
___
Emc-users mailing list
Emc-use
named sslbp. I take it that I have to compile that
somehow but I have no idea how. Any suggestions?
P.S. I am compiling the code for hm2pci project
--
Regards / Groete
Marius D. Liebenberg
082 698 3251
___
Emc-users mailing list
Emc-
On 8/27/2019 1:36 PM, Marius Liebenberg wrote:
Hi all
I need to set a 5i25 up as a dual lpt port. I want to replace my
mill installation with Path Pilot and I need the pin and bit
files to do that.
Does anyone know where I can go look for the files please?
http://freeby.mesanet.com
On 8/27/2019 8:48 PM, Marius Liebenberg wrote:
On 8/27/2019 1:36 PM, Marius Liebenberg wrote:
Hi all
I need to set a 5i25 up as a dual lpt port. I want to replace my
mill installation with Path Pilot and I need the pin and bit files
to do that.
Does anyone know where I can go look
On 8/27/2019 1:36 PM, Marius Liebenberg wrote:
Hi all
I need to set a 5i25 up as a dual lpt port. I want to replace my
mill installation with Path Pilot and I need the pin and bit files
to do that.
Does anyone know where I can go look for the files please?
http://freeby.mesanet.com
On 8/27/2019 1:36 PM, Marius Liebenberg wrote:
Hi all
I need to set a 5i25 up as a dual lpt port. I want to replace my mill
installation with Path Pilot and I need the pin and bit files to do that.
Does anyone know where I can go look for the files please?
--
Regards / Groete
Marius D
Hi all
I need to set a 5i25 up as a dual lpt port. I want to replace my mill
installation with Path Pilot and I need the pin and bit files to do that.
--
Regards / Groete
Marius D. Liebenberg
082 698 3251
___
Emc-users mailing list
Emc-users
Very interesting! I am impressed of what he does.
One comment calls him Дмитрий or Dmitrij, here are some of his posts:
http://www.cnc-club.ru/forum/viewtopic.php?f=41&t=12087&p=437308&hilit=sscnet%40yurtaev.com#p437308
This is his website, I think: http://www.yurtaev.com/
On 2019-02-03 05:32,
Subject: Re: [Emc-users] mach3(winderz) vs LCNC bob useage diffs
On Wednesday 02 January 2019 08:58:27 Marius Liebenberg wrote:
Gene
You can configure Mach3 to drive anything on any output pin. It is up
to the creator of the machine and the BOB that is used.
You can dump the enable
Gene
You can configure Mach3 to drive anything on any output pin. It is up to
the creator of the machine and the BOB that is used.
You can dump the enable signals and hard wire them to be on all the
time. The last thing you want is for the machine to have the steppers
switched of and some axis
Andy, sofar I know the Master must pull the bus high with a pull-up
resistor
-- Original Message --
From: "andy pugh"
To: "Enhanced Machine Controller (EMC)"
Sent: 2018-12-17 13:09:51
Subject: [Emc-users] SPI
Not as on-topic as I would like, but I suspect that some of you here
migh
Hi Jeff
Andy already fixed it so you probably removed the fixed text.
-- Original Message --
From: "Jeff Epler"
To: "Marius Liebenberg" ; "Enhanced Machine
Controller (EMC)"
Sent: 2018-11-21 21:52:11
Subject: Re: [Emc-users] Details change on forum
I
Done all that. I did read up on the forum software website that it is a
setting that the administrator has to set in the CB module. Or something
like that.
My info is outdated and I need to change it or delete it
-- Original Message --
From: "andy pugh"
To: "Ma
Hi
Does anyone know how to change profile details on the forum.
Specifically the signature. It used to be there but has since
disappeared.
___
Emc-users mailing list
Emc-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/emc-us
.
Remember this is crisis recovery and not the norm.
-- Original Message --
From: "Thaddeus Waldner"
To: "Marius Liebenberg" ; "Enhanced Machine
Controller (EMC)"
Sent: 2018-11-20 18:50:26
Subject: Re: [Emc-users] UPS on controller
I’m intrigued by the “record
I agree with Andy. I put my controllers on a UPS and then have a signal
that is wired through a drop-out relay that is also connected to the
emergency stop switch. So when the power fails the machine is stopped
and you can record line numbers at least and then shut down.
-- Original Messag
.
-
Regards / Groete
Marius D. Liebenberg
+27 82 698 3251
+27 12 743 6064
___
Emc-users mailing list
Emc-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/emc-users
The machine "works", as in they've made a half dozen ugly test cuts.
But they have not figured out how to make the THC work right and some
other finer points of perfection still need fixing. Things like
squaring the gantry are currently done by grabbing the bridge and
pulling it forward ag
I have done many plasma machines over the years and I found that if the
customer is not capable of his own software or has no understanding of
LinuxCnc, then I just install Mach3.
Mach works very well for plasma.
Actually, a customer that is capable of fiddling the software is
normally your wo
only.
-- Original Message --
From: "Chris Albertson"
To: "Marius Liebenberg" ; "Enhanced Machine
Controller (EMC)"
Sent: 2018-04-05 18:54:35
Subject: Re: [Emc-users] One servo system
The comment to use psocketbeagle and MK if Linux is required is good.
I
"
To: "Marius Liebenberg"
Sent: 2018-04-04 13:37:56
Subject: Re: [Emc-users] One servo system
I think a simple real-time component should also do the trick in case
the ladder logic component (it's also RT right?) does not work for your
application.
The PocketBeagle also has
Controller (EMC)"
Cc: "Marius Liebenberg"
Sent: 2018-04-04 09:24:43
Subject: Re: [Emc-users] One servo system
Machinekit + PocketBeagle is good combo if you are looking for
something
running Linux.
Chris Albertson writes:
Of course. Write a PID based control loop and put it
t from the start
that you are not wasting your money on another failed attempt at
building a special machine.
-- Original Message --
From: "andy pugh"
To: "Marius Liebenberg" ; "Enhanced Machine
Controller (EMC)"
Sent: 2018-04-02 21:44:36
Subject
Probably about 25mm shaft. So as I need 1000 to 1500 RPM for the
plastics it seems doable then.
-- Original Message --
From: "Ed"
To: emc-users@lists.sourceforge.net
Sent: 2018-04-02 16:58:56
Subject: Re: [Emc-users] What RPM
On 04/02/2018 09:23 AM, Marius Liebenberg wr
e.net
Sent: 2018-04-02 17:33:21
Subject: Re: [Emc-users] What RPM
On Monday 02 April 2018 10:23:33 Marius Liebenberg wrote:
Hi
I have had this piece of machine in the store for a long time. I
think
it was used to decant fishing line to the smaller plastic reels.
I have a need for a small dedic
It looks like the bearings were submerged in oil on the the machine as
both are sitting in a sump with oil drain each. The top bearing has
large feed groove for the oil. That will only work if submerged.
-- Original Message --
From: "jeremy youngs"
To: "Enhanced Machine Controller (EM
question is what are
the other options if any.
-
Regards / Groete
Marius D. Liebenberg
+27 82 698 3251
+27 12 743 6064
--
Check out the vibrant tech community on one of the world's most
eng
-- Original Message --
From: "andy pugh"
To: "Marius Liebenberg" ; "Enhanced Machine
Controller (EMC)"
Sent: 2017-11-28 12:11:59
Subject: Re: [Emc-users] How to setup a system for Uspace
On 28 November 2017 at 07:01, Marius Liebenberg
wrote:
So
.
-
Regards / Groete
Marius D. Liebenberg
+27 82 698 3251
+27 12 743 6064
---
This email has been checked for viruses by Avast antivirus software.
https://www.avast.com/antivirus
--
Check out the vibrant tech community on
Not sure what the conditions are but I dont remember any restrictions.
Please PM me for the link.
-- Original Message --
From: "Chris Albertson"
To: "Marius Liebenberg" ; "Enhanced Machine
Controller (EMC)"
Sent: 2017-10-13 20:52:23
Subject: Re: [Emc
I have a source code CD that I paid $10 for to cover shipping and other
costs.
Tormach says they don't support path pilot on 3rd party equipment. It
likely
depends on specialized hardware so it would not run without
modification
and I don't think they have source code available.
As
On 11 September 2017 at 04:44, Marius Liebenberg
wrote:
I Is there anyone out there that
has some examples that I can look at to get started please?
Or some advise will do as well thanks.
Take a look at:
https://github.com/LinuxCNC/linuxcnc/blob/master/src/hal/drivers/mesa_uart.comp
.
-- Original Message --
From: "Erik Christiansen"
To: emc-users@lists.sourceforge.net
Sent: 2017-09-11 14:40:15
Subject: Re: [Emc-users] Mesa RS-422 examples
TL;DR: Potted solutions are at the end.
On 11.09.17 11:44, Marius Liebenberg wrote:
Hi
I need to write a custom RS-422 protocol
hat I can look at to get started please?
Or some advise will do as well thanks.
-
Regards / Groete
Marius D. Liebenberg
+27 82 698 3251
+27 12 743 6064
---
This email has been checked for viruses by Avast antivirus software.
https://www.avast.com/anti
Hi Johan
You will have to provide a bit more detail in order to get assistance.
Please explain what you mean by "does not hold size at all"
Explain how:
1) you discovered the problem and
2) how you measured the result and
3) what you done to solve it thus far.
Also give details on the controller
input
for velocity mode.
The question is what mode is better to use with LCNC and Mesa cards,
velocity or position?
I will use one of the Ethernet solutions from Mesa with a panel PC.
-
Regards / Groete
Marius D. Liebenberg
+27 82 698 3251
+27 12 743
,
velocity or position?
I will use one of the Ethernet solutions from Mesa with a panel PC.
-
Regards / Groete
Marius D. Liebenberg
+27 82 698 3251
+27 12 743 6064
---
This email has been checked for viruses by Avast antivirus software.
https://www.avast.com/antivirus
On 16 July 2017 at 14:33, Gene Heskett wrote:
Is there a clever way to drive this with with 7i76.
Possibly with a DC boost converter. Do you have 10V anywhere else?
No not at all. I was wondering if I could use a voltage divider to bring
the 24v down to 12v at least as the 7i76 spindle
Hi
I have to replace my lathe drive and the one I have does not have a 10v
source for the 7i76 card produce the 0 - 10v signal.
Is there a clever way to drive this with with 7i76.
-
Regards / Groete
Marius D. Liebenberg
+27 82 698 3251
+27 12 743 6064
---
This
Sorry, latest news: the same happens with other 7i77.
05/29/2017 10:15 AM, Marius Alksnys rašė:
Peter, can you repair or help me to repair this 7i77 board? Maybe I
could diagnose more or let you connect to the system remotely.
I also can replace PCB components like PIC...
I issued a RMA
.
05/16/2017 09:35 PM, Peter C. Wallace rašė:
On Tue, 16 May 2017, Marius Alksnys wrote:
Date: Tue, 16 May 2017 21:02:29 +0200
From: Marius Alksnys
Reply-To: "Enhanced Machine Controller (EMC)"
To: emc-users@lists.sourceforge.net
Subject: Re: [Emc-users] Had to re-flash Mesa 7i77
We replaced 7i77 with a spare one and the machine is working without a
glitch for two weeks.
04/24/2017 06:17 PM, Peter C. Wallace rašė:
>
> This is most likely to be a PCI issue
>
> (those errors are what you would get if the 5I25 card suddenly disappeared and
> you read all FFs from the registe
1 - 100 of 838 matches
Mail list logo