Hello kqt4at5v (what a name!)
this kind of collet is the standard tool holder on my Steinel vertical
mill, in size ER40 with a Morse taper 3 shank. Very reliable, just once,
with very large cutting force in cast iron, the 12 mm bit got pulled out
gradually, digging deeper and deeper. I noticed
On Tue, 1 Nov 2011, BRIAN GLACKIN wrote:
One thing to consider is that the power to cut with a 1/8 endmill is
dramatically less than needed for a 1/4 and 1/2 inch endmill. Why not
consider swapping out your router with a decent electric long shaft die
grinder - they give the collet size and
On 2 November 2011 09:03, kqt4a...@comcast.net wrote:
That is my other option but I have realign my work
For this project I start with 1/4 bit to remove a lot of material
Then switch to a 1/8 bit then to a 1/16 bit to finish
If I change routers I have to hope I get the alignment correct
Do
On Wed, 2 Nov 2011, andy pugh wrote:
On 2 November 2011 09:03, kqt4a...@comcast.net wrote:
That is my other option but I have realign my work
For this project I start with 1/4 bit to remove a lot of material
Then switch to a 1/8 bit then to a 1/16 bit to finish
If I change routers I have
On 2 November 2011 13:41, kqt4a...@comcast.net wrote:
I may have to make friends with a local machinist
Could get pricey
You probably already know one, where is local?
--
atp
Torque wrenches are for the obedience of fools and the guidance of wise men
On Wed, 2011-11-02 at 08:41 -0500, kqt4a...@comcast.net wrote:
On Wed, 2 Nov 2011, andy pugh wrote:
On 2 November 2011 09:03, kqt4a...@comcast.net wrote:
That is my other option but I have realign my work
For this project I start with 1/4 bit to remove a lot of material
Then switch
On Wed, 2 Nov 2011, Kirk Wallace wrote:
On Wed, 2011-11-02 at 08:41 -0500, kqt4a...@comcast.net wrote:
On Wed, 2 Nov 2011, andy pugh wrote:
On 2 November 2011 09:03, kqt4a...@comcast.net wrote:
That is my other option but I have realign my work
For this project I start with 1/4 bit to
On Wednesday, November 02, 2011 11:20:29 AM kqt4a...@comcast.net did opine:
On Wed, 2 Nov 2011, andy pugh wrote:
On 2 November 2011 09:03, kqt4a...@comcast.net wrote:
That is my other option but I have realign my work
For this project I start with 1/4 bit to remove a lot of material
On Wed, 2011-11-02 at 09:47 -0500, kqt4a...@comcast.net wrote:
On Wed, 2 Nov 2011, Kirk Wallace wrote:
... snip
This ER tool holder could be used with a couple of bearings, pulleys and
timing belt to your existing spindle motor.
Can you point me to a USA source for pillow-blocks good for
On Wed, 2 Nov 2011, Kirk Wallace wrote:
On Wed, 2011-11-02 at 08:41 -0500, kqt4a...@comcast.net wrote:
On Wed, 2 Nov 2011, andy pugh wrote:
On 2 November 2011 09:03, kqt4a...@comcast.net wrote:
That is my other option but I have realign my work
For this project I start with 1/4 bit to
On 2 November 2011 21:17, kqt4a...@comcast.net wrote:
Not being very machinist savvy hope y'all will not mind one more question
Is this what I am looking for
http://pdf.directindustry.com/pdf/hardinge-workholding/toolholder-collets-bushings-tool-holders/17884-13582-_19.html
Part number
That looks like it'll do it.
And what would I need to go with it
safety glasses :-)
also, it looks like the nut is a separate part number, so you'll need
that, and if it doesn't come with the collet you'll need an ER-11 1/8
collet, like this one:
I know this has nothing to do with emc but you people represent centuries of
experience
How's that for kissing up :)
I see lots of these 1/2 to 1/4 adapters
http://www.mlcswoodworking.com/shopsite_sc/store/html/smarthtml/pages/router_collet.html
but what about one for 1/4 router and 1/8 bits
I
I have used 1/4 X 1/8 collet adapters with good success. I cannot recall
the supplier, but they are one of the companies that specializes in
supplies woodworking tools to instrument makers - Stewart perhaps?
Brian
On Tue, Nov 1, 2011 at 4:35 PM, kqt4a...@comcast.net wrote:
I know this has
If you can find out what the existing collet is usually you can get a
replacement with a different inner diameter. For instance, if it's a
small router (like a rotozip) it might have an ER-11 collet. A bigger
router might have an ER-25 or something. Then you can go to Amazon
and type in ER-25
On Tue, 1 Nov 2011, BRIAN GLACKIN wrote:
I have used 1/4 X 1/8 collet adapters with good success. I cannot recall
the supplier, but they are one of the companies that specializes in
supplies woodworking tools to instrument makers - Stewart perhaps?
Brian
On Tue, Nov 1, 2011 at 4:35 PM,
One thing to consider is that the power to cut with a 1/8 endmill is
dramatically less than needed for a 1/4 and 1/2 inch endmill. Why not
consider swapping out your router with a decent electric long shaft die
grinder - they give the collet size and the extension. Milwalkee and Bosch
both make
17 matches
Mail list logo
