Re: [wsjt-devel] v2.1.2 Radio On/Off CAT Problem?

Hi, I've just checked my Kenwood: * Turned the rig on and changed the frequency from that last used with WSJT-X 2.2.1 * Turned rig off at it's power button but leaving PSU on * Started WSJT-X 2.2.1 * Rig turned on and WSJT-X changed to the new frequency, rig beeped * Closed WSJT-X, rig st

Re: [wsjt-devel] v2.1.2 Radio On/Off CAT Problem?

Omitted to add that with my tests below, no I don't have that box set either. Alan G0TLK On 09/06/2020 09:36, Alan Groups wrote: Hi, I've just checked my Kenwood: * Turned the rig on and changed the frequency from that last used with WSJT-X 2.2.1 * Turned rig off at it's power button

Re: [wsjt-devel] wsjt-devel Digest, Vol 76, Issue 93

Hi Bill – The 2.1.x versions of wsjt-x decoding works well, both fast and normal decode. The fast decode is a little quicker on 2.1.x, but both can be used without an issue. Using a 2.2.x version, decoding on a busy band has the following behavior: first decode in cycle picks up a few messa

Re: [wsjt-devel] wsjt-devel Digest, Vol 76, Issue 93

Hi Tony, > Using a 2.2.x version, decoding on a busy band has the following behavior: > first decode in cycle picks up a few messages, second decode a few, then the > third decode runs a long time (well into the next cycle) and the majority of > messages get decoded on that third decode. What

Re: [wsjt-devel] Drop down band-selector list problem

Hello Reino, For some reason my screen capture program would not work with the drop down menu, so I photographed the before and after menus. This is the menu before adding another FT8 frequency: http://aa4m.com/Pic1.jpg And this is the menu after adding 7.071, FT8, All regions: http://aa4m.

Re: [wsjt-devel] Drop down band-selector list problem

Hi Bill, does restarting WSJT-X sort out the band/frequency drop down list? The 'S' in the circle to the left of the frequency display indicates that one of the "Settings->Radio->Split Operating" options has been selected. 73 Bill G4WJS. On 09/06/2020 14:38, Bill Mullin wrote: Hello Reino,

[wsjt-devel] WSJT-X Action on shutdown

"I'm the hamlib primary developer right now and not inclined to turn off the rig when closing the client.?" In my opinion WSJT-X should not make any change to the rig state when it shuts down. Several times I transitioned from working FT8 to attempting to work CW DX. If I shutdown WSJT-X whil

Re: [wsjt-devel] wsjt-devel Digest, Vol 76, Issue 93

> On Jun 9, 2020, at 07:39, Steven Franke via wsjt-devel > wrote: > > What are your typical DT values, i.e. what is the median DT value for a cycle > that has a good number of decodes? Normally, we expect to see the bulk of > the decodes produced by the first decoding segment (say, 80%) and

Re: [wsjt-devel] Drop down band-selector list problem

My settings are Arial, Regular, Bold, 8.  Your settings also caused the truncation on my WSJT display. My full display is set for 1600x900, I tried a number of different display modes but none made any difference.  So I reset Arial, Bold, 8 to Arial, Regular, 8 with no difference.  So then I t

Re: [wsjt-devel] Drop down band-selector list problem

Hey Reino, I've tried dragging the border to the right with no luck.  Being able to enlarge the window such as you have done would solve the problem forever! :-) 73, Bill On 06/09/2020 08:14:29, Reino Talarmo wrote: Hello Bill, Thanks for the pictures. I myself use Windows PrtSc key take

Re: [wsjt-devel] Drop down band-selector list problem

On 09/06/2020 16:14, Bill Mullin wrote: Here's something to think about.  When I added 7.071 to the menu, this should have made no difference to the drop down menu since the characters "7.071" are the same width or even smaller than many of the other lines in the menu.  It makes no sense that t

Re: [wsjt-devel] Drop down band-selector list problem

Hello Bill, I'm not sure what you're talking about?  Here's the list without the 7.071: http://aa4m.com/Pic1.jpg And here it is with the 7.071: http://aa4m.com/Pic2.jpg 73, Bill  AA4M Tucson, AZ On 06/09/2020 08:30:04, Bill Somerville wrote: On 09/06/2020 16:14, B

Re: [wsjt-devel] Drop down band-selector list problem

Oops, I'll try again, sorry! Hello Bill, I'm not sure what you're talking about?  Here's the list without the 7.071: http://aa4m.com/Pic1.jpg And here it is with the 7.071: http://aa4m.com/Pic2.jpg 73, Bill  AA4M Tucson, AZ On 06/09/2020 08:30:04, Bill Somerville wrote: On 09/06/2020 16:14

Re: [wsjt-devel] Drop down band-selector list problem

Hi Bill, OK, now I see two. Is there another mistyped one further down the list? 73 Bill G4WJS. On 09/06/2020 17:15, Bill Mullin wrote: Oops, I'll try again, sorry! Hello Bill, I'm not sure what you're talking about?  Here's the list without the 7.071: http://aa4m.com/Pic1.jpg And here i

Re: [wsjt-devel] Drop down band-selector list problem

Bill, that doesn't tell me much, but I was assuming that you *added* 7.071 MHz, rather than replaced 7.074 MHz,  since you said in you OP "I tried adding the new frequencies". I would expect to see two 7MHz frequencies on the drop down list, but you image only shows one. If you had inadverten

[wsjt-devel] How can I determine the version number of the installed 'wsprd' from the Linux command line?

I want sites running my 'wsprdaemon' to benefit from the improved decoding performance of the V2.2 wsprd decoder, but I am not sure how to determine which version of wsprd is installed. wsprd 2.1.x added '-o ...' to the help printout, but there is no such difference between 2.1.x and 2.2.x. Othe

Re: [wsjt-devel] How can I determine the version number of the installed 'wsprd' from the Linux command line?

On 09/06/2020 16:51, Rob Robinett wrote: I want sites running my 'wsprdaemon' to benefit from the improved decoding performance of the V2.2 wsprd decoder, but I am not sure how to determine which version of wsprd is installed. wsprd 2.1.x added '-o ...' to the help printout, but there is no su

Re: [wsjt-devel] How can I determine the version number of the installed 'wsprd' from the Linux command line?

> On Jun 9, 2020, at 12:09 PM, Bill Somerville wrote: > > On 09/06/2020 16:51, Rob Robinett wrote: >> I want sites running my 'wsprdaemon' to benefit from the improved decoding >> performance of the V2.2 wsprd decoder, but I am not sure how to determine >> which version of wsprd is installed. >

Re: [wsjt-devel] How can I determine the version number of the installed 'wsprd' from the Linux command line?

Thanks Bill and Steve, I noticed the change in format of ALL_WSPR.TXT and so I now know to use the field count of existing ALL_WSPR.TXT files to trigger a WSJT-x upgrade. However this seems a very awkward way to determine the version of wsprd, so if there is another wsprd upgrade, could you add a

Re: [wsjt-devel] WSJT-X 2.2.x decode performance on RigPi

On 2020-06-09 10:21 a.m., Tony wrote: Hi Bill – The 2.1.x versions of wsjt-x decoding works well, both fast and normal decode. The fast decode is a little quicker on 2.1.x, but both can be used without an issue. Using a 2.2.x version, decoding on a busy band has the following behavior: fi

Re: [wsjt-devel] WSJT-X 2.2.1 GA Release

I was able to test with a friend that has an IC-7300 and we could duplicate this problem -- but it's not easily reproducible. Has nothing to do with WSJT-X or hamlib.  Appears to be some sort of bug in the IC-7300 where changing bands and quickly transmitting is causing some sort of burp that tu

Re: [wsjt-devel] wsjt-devel Digest, Vol 76, Issue 93

On 6/9/20 3:39 PM, Steven Franke via wsjt-devel wrote: Hi Steven, Using a 2.2.x version, decoding on a busy band has the following behavior: first decode in cycle picks up a few messages, second decode a few, then the third decode runs a long time (well into the next cycle) and the majority of

[wsjt-devel] WSJT-X 2.2.1 GA, Hamlib error with FTdx3000 and Microham II router

Starting WSJT-X with FTdx3000 and using 2nd CAT port in MicroHams device router gives Hamlib error. de OH6VDA TOM ___ wsjt-devel mailing list wsjt-devel@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/wsjt-devel