Katarina wrote:
> What is the difference between a volt-ohm meter and a PWT? And what
> is the practical difference in terms of keeping your CS manufacture
> consistent? I've already ordered the PWT -- but I assumed it was
> only useful for making sure my distilled water was okay -- from your
> description it sounds like it will also help me tell approximately
> where I am in the process as I make my cs so I know where to end my
> run. So what would I need a voltage meter for?

If you dig up Chuck's little jpeg diagram he attached to one of his
messages earlier you'll see that he suggests using the pulser as a
power supply and getting two new silver electrodes to actually go in
the glass. Then you could easily put a current meter in series with
one of the electrodes or measure the output voltage across the
electrodes by repositioning the meter connections.

The advantage of this is learning how much current your pulser
actually pushes through the system. We know that too high a current
tends to create larger particles.

If the pulser just gives you a voltage regulated DC supply, with no
built in current limiting other than the 20 milliamp max rating
somebody mentioned for it, then you'll know not to push your
generating time so far that you end up making big particles that 
don't really add to the effectiveness of your product.

> And how do I tell if the water is good? If it is too conductive does
> that mean there is too much stuff in it that I wouldn't want? And
> since I gather it reads in Microseimens rather than ppm - what would
> be too high of a reading?

Others can give you their ideas, but the bottom line is if you have
some water that makes good CS, that's at least one data point.
Experience will show you what your limit should be.

> It sounds rather complicated for me to use a voltage ohms meter with
> my becks pulser since I would have to dismantle it in order to put
> anything in series - so I'd just as soon not bother if I don't need
> to. Also, from Chucks description I would have to get another silver
> electrode and add it to the mix and I don't know how that would
> effect the cs production.

I'd still want some others' input, but I think that a PWT will give 
you a direct measurement of what you're really interested in. Still, 
being able to measure the current out put of the pulser, at least 
once, would tell you how long you can run things before the current 
takes off to unhappy levels.

Please understand that all these measurements are really related. 

If you measure the voltage between the electrodes and the current
flowing from one to the other, divide the voltage by the current,
you'll get the resistance of the cell at that moment. (Literally, the 
water's resistance to the flow of current.)

Conductance is just 1 divided by the resistance, and conductivity is 
just conductance normalized to a standard size of measurement cell 
(Bob Berger's probe with 2 one centimeter square plates one cm 
apart). 

(Boy I hope I got this part right. It's been a while since I actually
*used* any of this conductance/conductivity stuff!)

So you could convert your current and voltage readings to the same 
conductivity measurement made by the PWT by figuring out the 
conversion factor for your electrode spacing and surface area, plus 
fudge factors for temperature and god knows what else, that Hanna 
has already taken care of for you. 

So if all you wanted to know was if *this* batch had reached the same 
approximate conductivity as the last batch, either the PWT reading or 
the current reading would tell you, though they'd be very different 
actual numbers with different units of measure (milliamps vs. 
microSiemens). They would still need to be the same from batch to 
batch.

I would still suggest you buy a cheap, $20 digital multimeter from 
Radio Shack or somewhere and learn to use it. It's damn useful for 
silly things like measuring battery voltage and you *can* rig it up 
to see what kind of current limiting the pulser does for you, if any. 
That will give you some ideas on limits for your process.

Whew! I'm sure this isn't getting a whole lot simpler for you. Just 
remember that the stuff you're making is working. All of this 
other nonsense will just give you a *little* more control once you 
figure out how to use the tools.

Keep asking questions. We'll get through it one way or another. 
<smile>

Mike D.

[Mike Devour, Citizen, Patriot, Libertarian]
[[email protected]                       ]
[Speaking only for myself...              ]


--
The silver-list is a moderated forum for discussion of colloidal silver.

To join or quit silver-list or silver-digest send an e-mail message to: 
[email protected]  -or-  [email protected]
with the word subscribe or unsubscribe in the SUBJECT line.

To post, address your message to: [email protected]
Silver-list archive: http://escribe.com/health/thesilverlist/index.html
List maintainer: Mike Devour <[email protected]>