Hi Mike,
unfortunately Chuck's jpeg diagram only comes over as a bunch of letters on
my Mac and I'm also computer illiterate and have no idea why it won't read
it.

I don't know if I am more or less confused by all this at the moment. I
think I'll wait and see what the PWT is like and check it out some and then
my questions may be able to be more specific.

I thought that Chuck was saying to get one new electrode to put in the glass
- not two -- but maybe I'm wrong. Chuck?? So if I get a multimeter I will
also have to get new wires/electrodes and plugs for the wire to attatch to
my silver pulser --- I think I need to look at a multimeter to even
understand how this will work -- when I look at things it's easier.

I doubt that the pulser is current limiting - but maybe I'm wrong.

Any guesses at all as to what will be a good reading on the PWT for my
distilled water?? So I have a jumping off point??

Thanks for trying to explain it -- it's funny what a huge gap there is
between those of us who are not at all technical and those who understand
it. I think what I need is someone to just very simply explain from scratch
what each meter does, how it reads out and how you make it work as if I was
a 10 yr old. Jeffrey care to try? Any takers?

Thanks so much.

Be well.
Katarina


> Katarina wrote:
>> What is the difference between a volt-ohm meter and a PWT? And what
>> is the practical difference in terms of keeping your CS manufacture
>> consistent? I've already ordered the PWT -- but I assumed it was
>> only useful for making sure my distilled water was okay -- from your
>> description it sounds like it will also help me tell approximately
>> where I am in the process as I make my cs so I know where to end my
>> run. So what would I need a voltage meter for?
>
> If you dig up Chuck's little jpeg diagram he attached to one of his
> messages earlier you'll see that he suggests using the pulser as a
> power supply and getting two new silver electrodes to actually go in
> the glass. Then you could easily put a current meter in series with
> one of the electrodes or measure the output voltage across the
> electrodes by repositioning the meter connections.
>
> The advantage of this is learning how much current your pulser
> actually pushes through the system. We know that too high a current
> tends to create larger particles.
>
> If the pulser just gives you a voltage regulated DC supply, with no
> built in current limiting other than the 20 milliamp max rating
> somebody mentioned for it, then you'll know not to push your
> generating time so far that you end up making big particles that
> don't really add to the effectiveness of your product.
>
>> And how do I tell if the water is good? If it is too conductive does
>> that mean there is too much stuff in it that I wouldn't want? And
>> since I gather it reads in Microseimens rather than ppm - what would
>> be too high of a reading?
>
> Others can give you their ideas, but the bottom line is if you have
> some water that makes good CS, that's at least one data point.
> Experience will show you what your limit should be.
>
>> It sounds rather complicated for me to use a voltage ohms meter with
>> my becks pulser since I would have to dismantle it in order to put
>> anything in series - so I'd just as soon not bother if I don't need
>> to. Also, from Chucks description I would have to get another silver
>> electrode and add it to the mix and I don't know how that would
>> effect the cs production.
>
> I'd still want some others' input, but I think that a PWT will give
> you a direct measurement of what you're really interested in. Still,
> being able to measure the current out put of the pulser, at least
> once, would tell you how long you can run things before the current
> takes off to unhappy levels.
>
> Please understand that all these measurements are really related.
>
> If you measure the voltage between the electrodes and the current
> flowing from one to the other, divide the voltage by the current,
> you'll get the resistance of the cell at that moment. (Literally, the
> water's resistance to the flow of current.)
>
> Conductance is just 1 divided by the resistance, and conductivity is
> just conductance normalized to a standard size of measurement cell
> (Bob Berger's probe with 2 one centimeter square plates one cm
> apart).
>
> (Boy I hope I got this part right. It's been a while since I actually
> *used* any of this conductance/conductivity stuff!)
>
> So you could convert your current and voltage readings to the same
> conductivity measurement made by the PWT by figuring out the
> conversion factor for your electrode spacing and surface area, plus
> fudge factors for temperature and god knows what else, that Hanna
> has already taken care of for you.
>
> So if all you wanted to know was if *this* batch had reached the same
> approximate conductivity as the last batch, either the PWT reading or
> the current reading would tell you, though they'd be very different
> actual numbers with different units of measure (milliamps vs.
> microSiemens). They would still need to be the same from batch to
> batch.
>
> I would still suggest you buy a cheap, $20 digital multimeter from
> Radio Shack or somewhere and learn to use it. It's damn useful for
> silly things like measuring battery voltage and you *can* rig it up
> to see what kind of current limiting the pulser does for you, if any.
> That will give you some ideas on limits for your process.
>
> Whew! I'm sure this isn't getting a whole lot simpler for you. Just
> remember that the stuff you're making is working. All of this
> other nonsense will just give you a *little* more control once you
> figure out how to use the tools.
>
> Keep asking questions. We'll get through it one way or another.
> <smile>
>
> Mike D.


--
The silver-list is a moderated forum for discussion of colloidal silver.

To join or quit silver-list or silver-digest send an e-mail message to: 
[email protected]  -or-  [email protected]
with the word subscribe or unsubscribe in the SUBJECT line.

To post, address your message to: [email protected]
Silver-list archive: http://escribe.com/health/thesilverlist/index.html
List maintainer: Mike Devour <[email protected]>