With a pair of pipe stands,It's easily a one man task. Mark at Aero Sent from my iPhone
> On Apr 9, 2014, at 10:42 AM, "rongreenman ." <[email protected]> wrote: > > Too bad, I was liking the 2 1/2" plastic pipe caps idea a lot. The removing > the entire test header is Ok but that has to be at least two and probably > three guys on anything bigger that a couple of three valves. > > > On Wed, Apr 9, 2014 at 10:20 AM, Bobby McCullough < > [email protected]> wrote: > >> My mistake. The 2.5" plastic caps are hose threads & installed on the >> valve where only the caps were stolen, which is common. I only have a >> few projects with valves stolen & there we used threaded ductile caps on >> the nipples & locked the valves in the pump room. >> >> -----Original Message----- >> From: [email protected] >> [mailto:[email protected]] On Behalf Of Ben >> Young >> Sent: Wednesday, April 09, 2014 12:05 PM >> To: [email protected] >> Subject: Re: pump test header valves >> >> Bobby, >> >> Do you mean screw-on PVC caps, or the plastic break caps for FDC snoots? >> >> Thanks for the feeback everyone, I didn't realize this was so common. >> I'll have to start recommending this to some of our clients in high >> theft areas from now on. >> >> >> Benjamin Young >> >> >> On Wed, Apr 9, 2014 at 9:50 AM, Bobby McCullough >> <[email protected] >>> wrote: >> >>> We use 2.5" plastic caps. Not much value at the scrap yard. Take the >> >>> valves in the pump room and use a bicycle cable & lock to keep them >>> from wandering off. >>> >>> Bobby McCullough >>> Atlanta Sprinkler >>> >>> >>> -----Original Message----- >>> From: [email protected] >>> [mailto:[email protected]] On Behalf Of >>> Morey, Mike >>> Sent: Wednesday, April 09, 2014 8:49 AM >>> To: [email protected] >>> Subject: RE: pump test header valves >>> >>> They make test header outlets with male threaded outlets (basically >>> the opposite of an FDC) with hose caps that you remove and then screw >>> on hose valves that have a female swivel on the inlet side. Of course >> >>> there's still the risk of someone stealing the hose caps and/or brass >>> adapteer fittings that provide the male hose thread, but at least the >>> valves aren't sitting out there too. >>> >>> Mike Morey, CFPS, SET >>> Planner Scheduler/Designer >>> BMWC Constructors, Inc. >>> 1740 W. Michigan St, Indianapolis, IN 46222 >>> O: 317.651.0596 | C: 317.586.8111 >>> [email protected] | www.bmwc.com >>> >>> ________________________________________ >>> From: [email protected] >>> <[email protected]> on behalf of Ben >>> Young <[email protected]> >>> Sent: Wednesday, April 09, 2014 8:40 AM >>> To: [email protected] >>> Subject: pump test header valves >>> >>> Last week I was at an ASCET meeting where a pump presentation was >> given. >>> >>> Someone asked the presenter if it was allowed to remove the test >>> header valves and keep them in the pump room to stop them from being >> stolen. >>> >>> The presenter and few other attendees chimed in that this was ok, and >>> nothing in 20 or 25 said the valves had to be constantly in place. >>> >>> I didn't think of it at the time, but now I'm asking myself how then >>> do you keep debris out of the test header? The only thing I can think >> >>> of is that you would have to cap the nipples or if you remove the >>> nipples, plug the holes in the test header. This sounds like it will >>> cause problems down the road to me. >>> >>> Have you guys ever seen this done before? >>> >>> Benjamin Young >>> _______________________________________________ >>> Sprinklerforum mailing list >>> [email protected] >>> http://lists.firesprinkler.org/listinfo.cgi/sprinklerforum-firesprinkl >>> er >>> .org >>> _______________________________________________ >>> Sprinklerforum mailing list >>> [email protected] >>> http://lists.firesprinkler.org/listinfo.cgi/sprinklerforum-firesprinkl >>> er >>> .org >>> _______________________________________________ >>> Sprinklerforum mailing list >>> [email protected] >>> >>> http://lists.firesprinkler.org/listinfo.cgi/sprinklerforum-firesprinkl >>> er.org >> _______________________________________________ >> Sprinklerforum mailing list >> [email protected] >> http://lists.firesprinkler.org/listinfo.cgi/sprinklerforum-firesprinkler >> .org >> _______________________________________________ >> Sprinklerforum mailing list >> [email protected] >> >> http://lists.firesprinkler.org/listinfo.cgi/sprinklerforum-firesprinkler.org > > > > -- > Ron Greenman > Instructor > Fire Protection Engineering Technology > Bates Technical College > 1101 So. Yakima Ave. > Tacoma, WA 98405 > > [email protected] > > http://www.bates.ctc.edu/fireprotection/ > > 253.680.7346 > 253.576.9700 (cell) > > Member: > ASEE, SFPE, ASCET, NFPA, AFSA, NFSA, AFAA, NIBS, WSAFM, WFC, WFSC > > They are happy men whose natures sort with their vocations. -Francis Bacon, > essayist, philosopher, and statesman (1561-1626) > > A problem well stated is a problem half solved. -Charles F. Kettering, > inventor and engineer (1876-1958) > _______________________________________________ > Sprinklerforum mailing list > [email protected] > http://lists.firesprinkler.org/listinfo.cgi/sprinklerforum-firesprinkler.org > _______________________________________________ Sprinklerforum mailing list [email protected] http://lists.firesprinkler.org/listinfo.cgi/sprinklerforum-firesprinkler.org
