It's my go to frequency coordinator. There are others like Comsearch (Tim).
http://www.intelpath.com/ As far as I know she doesn't do any cat videos. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Dec 5, 2014 at 11:44 AM, That One Guy via Af <af@afmug.com> wrote: > What do you mean? I assume the vendor we paid to do the FCC process > handled that based on what the FCC says, we had to do a different polarity > because there is another 11ghz link in a similar path. What does this liz > lady do, is she the one who puts up all the cat videos on the internet? Im > always suspicious of women named liz. > > On Fri, Dec 5, 2014 at 10:39 AM, Josh Luthman via Af <af@afmug.com> wrote: > >> Who is responsible for figuring out your frequencies? While a vendor can >> do it, I'd suggest calling Liz @ IntelPath. >> >> >> Josh Luthman >> Office: 937-552-2340 >> Direct: 937-552-2343 >> 1100 Wayne St >> Suite 1337 >> Troy, OH 45373 >> >> On Fri, Dec 5, 2014 at 11:35 AM, That One Guy via Af <af@afmug.com> >> wrote: >> >>> I know the vendor sent me documentation on cabling/grounding, but I cant >>> find it anywhere. We are using the SAF POE injector/splitter. Both >>> components have surge suppression, but we also have an ALPU surge >>> suppressor and a DC surge suppressor, Im not sure where in the mix these >>> go, top/bottom etc. >>> >>> We did the expedited FCC approval, but dont have a PCN, does that come >>> directly to us or to the vendor that did it and is relayed to us. I dont >>> recall providing our FRN, so where will this license be applied? Is there a >>> way to get it into our FRN portal (the one for managing the 3.65 stuff) or >>> is that a separate type of license? >>> >>> On Fri, Dec 5, 2014 at 10:16 AM, Josh Luthman via Af <af@afmug.com> >>> wrote: >>> >>>> 35 miles since we're in 'merica. >>>> >>>> >>>> Josh Luthman >>>> Office: 937-552-2340 >>>> Direct: 937-552-2343 >>>> 1100 Wayne St >>>> Suite 1337 >>>> Troy, OH 45373 >>>> >>>> On Fri, Dec 5, 2014 at 11:14 AM, Hardy, Tim via Af <af@afmug.com> >>>> wrote: >>>> >>>>> Also, make sure that FCC Applications have been filed before turning >>>>> these on in the field (even for alignment or testing). The PCN does not >>>>> provide authorization to transmit, but you can operate under Conditional >>>>> Authority as long as the FCC Applications have been accepted for filing at >>>>> the FCC, the applications did not request a waiver, you are not located in >>>>> a quiet zone, and you are not located within 56.3 kilometers of an >>>>> international border. >>>>> >>>>> >>>>> >>>>> *From:* Af [mailto:af-boun...@afmug.com] *On Behalf Of *Mathew Howard >>>>> via Af >>>>> *Sent:* Friday, December 05, 2014 11:07 AM >>>>> *To:* af@afmug.com >>>>> *Subject:* Re: [AFMUG] SAF CFIP Lumina 11ghz setup >>>>> >>>>> >>>>> >>>>> Yes, you are going to want to have the PCN in hand for configuring to >>>>> make sure you get frequencies on the right side, TX power, polarity and >>>>> all >>>>> that right... I would think it would be pretty safe to assume you're >>>>> licensed for full power since you had to go with 4' dishes, but I'd still >>>>> want to check what the PCN says. >>>>> >>>>> I don't remember running into any particular problems setting ours up, >>>>> but it's been a few years. >>>>> >>>>> I do not recommend strapping the dish to your back to carry it up the >>>>> tower... >>>>> ------------------------------ >>>>> >>>>> *From:* Af [af-boun...@afmug.com] on behalf of Jeremy via Af [ >>>>> af@afmug.com] >>>>> *Sent:* Friday, December 05, 2014 10:01 AM >>>>> *To:* af@afmug.com >>>>> *Subject:* Re: [AFMUG] SAF CFIP Lumina 11ghz setup >>>>> >>>>> Also, all of the details, including transmit power, should be on the >>>>> PCN. You should have the PCN in hand. If you don't I would print it out. >>>>> You should also have a path analysis with expected signal strengths, and >>>>> those come in really handy when you are aligning. If you are not where >>>>> the >>>>> path calc says that you should be then you could be on a side lobe >>>>> >>>>> >>>>> >>>>> On Fri, Dec 5, 2014 at 8:59 AM, Jeremy <jeremysmi...@gmail.com> wrote: >>>>> >>>>> I haven't used SAF before but I generally set the radios across the >>>>> room from each other (with no dish) to test the link. They will link up >>>>> without being next to each other. >>>>> >>>>> >>>>> >>>>> On Fri, Dec 5, 2014 at 8:42 AM, That One Guy via Af <af@afmug.com> >>>>> wrote: >>>>> >>>>> We havent used SAF or done licensed before >>>>> >>>>> >>>>> >>>>> Im getting ready to bench configure this link, are there any caveats >>>>> to it? >>>>> >>>>> As I understand it from the manual, these ship with transmit turned >>>>> off, so powering them up wont hurt anything, I just set them side by side >>>>> with the flanges facing upward and turn the power on to the minimum tx >>>>> power, this wont hurt them to be transmitting with no antenna load >>>>> attached? If I leave them on for an extended timeframe will it harm them >>>>> in >>>>> this fashion? >>>>> >>>>> >>>>> >>>>> Im assuming the license gives use permission to install these at >>>>> maximum radio power? we dont have anything in hand from FCC so I dont >>>>> know, >>>>> all I know is we have approval on the link. >>>>> >>>>> >>>>> >>>>> Any gotchas to setting these up or installing them, beyond figuring >>>>> out how to get a 4 foot antenna to the top of the grain elevator without >>>>> denting it >>>>> >>>>> >>>>> >>>>> -- >>>>> >>>>> All parts should go together without forcing. You must remember that >>>>> the parts you are reassembling were disassembled by you. Therefore, if you >>>>> can't get them together again, there must be a reason. By all means, do >>>>> not >>>>> use a hammer. -- IBM maintenance manual, 1925 >>>>> >>>>> >>>>> >>>>> >>>>> >>>> >>>> >>> >>> >>> -- >>> All parts should go together without forcing. You must remember that the >>> parts you are reassembling were disassembled by you. Therefore, if you >>> can't get them together again, there must be a reason. By all means, do not >>> use a hammer. -- IBM maintenance manual, 1925 >>> >> >> > > > -- > All parts should go together without forcing. You must remember that the > parts you are reassembling were disassembled by you. Therefore, if you > can't get them together again, there must be a reason. By all means, do not > use a hammer. -- IBM maintenance manual, 1925 >