RSSI?
4-7dBm
On 6/5/2016 1:17 PM, Jay Weekley wrote:
What was the average signal difference?
Jerry Head wrote:
It absolutely does perform worse on the same link, we just helped a
friend move an entire site from UBNT to epmp to make use of the sync
capabilities. We actually had to transfer about 15% of the customers
to 900 because they would not work at all on epmp.
On 6/2/2016 4:31 PM, Mathew Howard wrote:
But does it actually perform worse that UBNT 2.4ghz on the same
link, or is it maybe just differences in how they calculate signal
levels? It doesn't make any sense that two different radios running
on the same frequency putting the same amount of power into the same
antennas would give significantly different signal levels...
The closest thing I've done to a comparison was playing with a Force
200 2.4ghz in wifi mode... there didn't seem to be a significant
difference between it and a PowerBeam connecting to the same AP.
On Thu, Jun 2, 2016 at 4:10 PM, Josh Luthman
<j...@imaginenetworksllc.com <mailto:j...@imaginenetworksllc.com>>
wrote:
And I've tried IT Elite dual pol panels, Force 200 2.4,
integrated + reflector for CPEs. Continues to suck.
Josh Luthman
Office: 937-552-2340 <tel:937-552-2340>
Direct: 937-552-2343 <tel:937-552-2343>
1100 Wayne St
Suite 1337
Troy, OH 45373
On Thu, Jun 2, 2016 at 5:08 PM, Ken Hohhof <af...@kwisp.com> wrote:
I’m thinking more the CPE antennas.
*From:* CBB - Jay Fuller <mailto:par...@cyberbroadband.net>
*Sent:* Thursday, June 02, 2016 3:59 PM
*To:* af@afmug.com
*Subject:* Re: [AFMUG] PMP450 vs. ePMP
hmm, i will check into that. Pretty sure with ubnt we're
using kp performance. With epmp, i think it is bundled
antennas...
----- Original Message -----
*From:* Ken Hohhof <mailto:af...@kwisp.com>
*To:* af@afmug.com <mailto:af@afmug.com>
*Sent:* Thursday, June 02, 2016 3:50 PM
*Subject:* Re: [AFMUG] PMP450 vs. ePMP
Jay, I suspect the difference you are seeing may be
mainly in the antennas. 2.4 GHz from any vendor should
penetrate the same, the radio waves don’t care what brand
radio launched them. And I think the difference between
the platforms will be most evident in low interference
environment where they can achieve their full modulation
and throughput. With low SNR, I think it’s kind of like
arguing Ferrari vs Porsche for off road racing, neither
will be able to show off its capabilities. Receiver
sensitivity and bits/sec/Hz won’t matter.
*From:* CBB - Jay Fuller <mailto:par...@cyberbroadband.net>
*Sent:* Thursday, June 02, 2016 3:28 PM
*To:* af@afmug.com
*Subject:* Re: [AFMUG] PMP450 vs. ePMP
Also interested in interference rejection of the pmp450
- is there any (in 2.4)
we are getting better foliage penetration with ubnt 2.4
than epmp 2.4 - - and from the performance of
the epmp 2.4 i wish wish wish it penetrated better!
----- Original Message -----
*From:* Matt <mailto:matt.mailingli...@gmail.com>
*To:* af@afmug.com <mailto:af@afmug.com>
*Sent:* Thursday, June 02, 2016 2:25 PM
*Subject:* [AFMUG] PMP450 vs. ePMP
We have mostly PMP100 and PMP450 deployed. Some
Ubiquiti we tried and
some we inherited as well. Have some ePMP we have
tested but so far
have not deployed more then couple test links.
For those who have tried both ePMP and PMP450 what
are the differences
you have seen in performance? Interference tolerance
among others?
For those that have gone with PMP450 over ePMP what
was the reasoning?
