What else you got laying around? Deluxe pipe? Rev F/G/H will work fine
with 12-56VDC.
On 6/15/2017 10:34 AM, Paul McCall wrote:
That’s what it appears. Am wondering if Forrest has a different
voltage range for input since he built it himself
Paul
*From:*Af [mailto:af-boun...@afmug.com] *On Behalf Of *George Skorup
*Sent:* Thursday, June 15, 2017 11:29 AM
*To:* af@afmug.com
*Subject:* Re: [AFMUG] Powering a Syncbox Junior without a uGPS type
device
I'm about 63.48% sure that UGPS power is like 5-7VDC which is on one
of the serial lines, IIRC.
On 6/15/2017 10:15 AM, Paul McCall wrote:
Soooo… can I power it off an S16 somehow, with the right cable?
(24v?)
Paul
*From:* Af [mailto:af-boun...@afmug.com] *On Behalf Of *Forrest
Christian (List Account)
*Sent:* Thursday, June 15, 2017 11:04 AM
*To:* af <af@afmug.com> <mailto:af@afmug.com>
*Subject:* Re: [AFMUG] Powering a Syncbox Junior without a uGPS
type device
OK found a short .pdf manual. Looks like the 100 series may not
support this.
The timing port model needs ugps power.
On Jun 15, 2017 9:46 AM, "Forrest Christian (List Account)"
<li...@packetflux.com <mailto:li...@packetflux.com>> wrote:
Hmm. ... odd. I know it's in the 450, but I thought it was
in the older radios too.
I'm traveling, so can't look it up, but what does the uGPS
manual say about FSK radios?
On Jun 15, 2017 9:42 AM, "George Skorup"
<george.sko...@cbcast.com <mailto:george.sko...@cbcast.com>>
wrote:
I don't have a single P10 or P11 FSK AP that has UGPS
power control on the config page. Perhaps it's just always on?
On 6/15/2017 9:35 AM, Forrest Christian (List Account) wrote:
AFAIK All semi-modern fsk radios provide uGPS power.
Just connect the radio and box together and turn on
uGPS power in the radio. Use whatever cable cambium
recommends for a uGPS probably just a 6p6c straight
through cable, although it might make sense to skip
the factory reset pin.
On Jun 15, 2017 9:19 AM, "Paul McCall"
<pa...@pdmnet.net <mailto:pa...@pdmnet.net>> wrote:
Hmmmm….. let me try again.
I have a single FSK AP that is getting
powered/ethernet successfully connected to a UBNT
S16. I need to get sync to that radio. I want to
power the SB Junior Timing Port Version by making
a cable that I can connect to the S16 that will
connect to one of the SBJTP timing ports to power
it up.
Unless that ALL FSKs timing ports actually would
provide the power needed to power up the SBJTV ?
with a “standard” cable whatever that means 😊
Paul
*From:* Af [mailto:af-boun...@afmug.com
<mailto:af-boun...@afmug.com>] *On Behalf Of
*Forrest Christian (List Account)
*Sent:* Thursday, June 15, 2017 10:08 AM
*To:* af <af@afmug.com <mailto:af@afmug.com>>
*Subject:* Re: [AFMUG] Powering a Syncbox Junior
without a uGPS type device
What type of fsk radio do you gave that doesn't do
ups power?
On Jun 15, 2017 9:04 AM, "Paul McCall"
<pa...@pdmnet.net <mailto:pa...@pdmnet.net>> wrote:
Syncbox Junior Timing Port Version
*From:* Af [mailto:af-boun...@afmug.com
<mailto:af-boun...@afmug.com>] *On Behalf Of
*Forrest Christian (List Account)
*Sent:* Thursday, June 15, 2017 10:03 AM
*To:* af <af@afmug.com <mailto:af@afmug.com>>
*Subject:* Re: [AFMUG] Powering a Syncbox
Junior without a uGPS type device
Which syncbox?
On Jun 15, 2017 8:51 AM, "Paul McCall"
<pa...@pdmnet.net <mailto:pa...@pdmnet.net>>
wrote:
Guys,
We need to providing timing on a single
FSK AP and it is fed up the tower through
fiber to a UBNT S16. (so its powering off
the S16). I want to use one timing port
to output timing to the FSK (as normal)
and one port to receive power from the S16
and need to figure out the pinout (wiring
diagram) to make that happen.
Paul
Paul McCall, President
PDMNet, Inc. / Florida Broadband, Inc.
658 Old Dixie Highway
Vero Beach, FL 32962
772-564-6800 <tel:%28772%29%20564-6800>
pa...@pdmnet.net <mailto:pa...@pdmnet.net>
www.pdmnet.com <http://www.pdmnet.com>
www.floridabroadband.com
<http://www.floridabroadband.com>