Hi, Androidphan wrote: > This is the output when starting wpa_supplicant: > > Initializing interface 'wlan0' conf '/system/etc/wifi/ > wpa_supplicant.conf' > drive > r 'wext' ctrl_interface 'N/A' bridge 'N/A' > Configuration file '/system/etc/wifi/wpa_supplicant.conf' -> '/system/ > etc/wifi/ > w > pa_supplicant.conf' > Reading configuration file '/system/etc/wifi/wpa_supplicant.conf' > update_config=1 > ctrl_interface='DIR=/data/system/wpa_supplicant/ GROUP=system' > eapol_version=1 > ap_scan=1 > fast_reauth=1 > Initializing interface (2) 'wlan0' > EAPOL: SUPP_PAE entering state DISCONNECTED > EAPOL: KEY_RX entering state NO_KEY_RECEIVE > EAPOL: SUPP_BE entering state INITIALIZE > EAP: EAP entering state DISABLED > EAPOL: External notification - portEnabled=0 > EAPOL: External notification - portValid=0 > SIOCGIWRANGE: WE(compiled)=22 WE(source)=21 enc_capa=0xf > capabilities: key_mgmt 0xf enc 0xf > WEXT: Operstate: linkmode=1, operstate=5 > Own MAC address: 00:22:43:2c:fa:a6 > wpa_driver_wext_set_wpa > wpa_driver_wext_set_key: alg=0 key_idx=0 set_tx=0 seq_len=0 key_len=0 > wpa_driver_wext_set_key: alg=0 key_idx=1 set_tx=0 seq_len=0 key_len=0 > wpa_driver_wext_set_key: alg=0 key_idx=2 set_tx=0 seq_len=0 key_len=0 > wpa_driver_wext_set_key: alg=0 key_idx=3 set_tx=0 seq_len=0 key_len=0 > wpa_driver_wext_set_countermeasures > ioctl[SIOCSIWAUTH]: Operation not supported on transport endpoint > WEXT auth param 4 value 0x0 - wpa_driver_wext_set_drop_unencrypted > Setting scan request: 0 sec 100000 usec > ctrl_interface_group=1000 (from group name 'system') > Added interface wlan0 > RTM_NEWLINK: operstate=0 ifi_flags=0x1002 () > RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added > Wireless event: cmd=0x8b06 len=8 > Ignore event for foreign ifindex 4 > RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP]) > RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added > State: DISCONNECTED -> SCANNING > CTRL-EVENT-STATE-CHANGE id=-1 state=2 > Starting AP scan (broadcast SSID) > Trying to get current scan results first without requesting a new scan > to > speed > up initial association > Received 0 bytes of scan results (0 BSSes) > Scan results: 0 > CTRL-EVENT-SCAN-RESULTS Ready > Hi, test you wifi connection using the wpa_cli program. The parse function of the scan result expect a - to the signal stregh (if I remember) to parse the result, otherwise fail.
wpa_cli has an interractive mode to operate, and you can send command like: scan and scan-results. > No suitable AP found. > Setting scan request: 0 sec 0 usec > No enabled networks - do not scan > State: SCANNING -> INACTIVE > CTRL-EVENT-STATE-CHANGE id=-1 state=1 > > > On 27 mrt, 11:39, Androidphan <niels.kee...@tass.nl> wrote: > >> I'm getting the following error at the moment: >> D/WifiHW ( 2325): Unable to open connection to supplicant on "/data/ >> system/wpa_supplicant/wlan0": No such file or directory >> >> I got wpa_supplicant running. >> >> # ls -l /data/system/wpa_supplicant/ >> srwxrwx--- root system 2009-03-27 11:39 wlan0 >> >> So it exists. >> >> Why is this?? >> > > > > Regards Michael --~--~---------~--~----~------------~-------~--~----~ unsubscribe: android-porting+unsubscr...@googlegroups.com website: http://groups.google.com/group/android-porting -~----------~----~----~----~------~----~------~--~---