# wpa_cli -p/data/system/wpa_supplicant/ scan Selected interface 'wlan0' Failed to connect to wpa_supplicant - wpa_ctrl_open: No such file or directory
On 27 mrt, 12:15, Michael Trimarchi <trimar...@gandalf.sssup.it> wrote: > Hi, > > > > Androidphan wrote: > > This is the output when starting wpa_supplicant: > > > Initializing interface 'wlan0' conf '/system/etc/wifi/ > > wpa_supplicant.conf' > > drive > > r 'wext' ctrl_interface 'N/A' bridge 'N/A' > > Configuration file '/system/etc/wifi/wpa_supplicant.conf' -> '/system/ > > etc/wifi/ > > w > > pa_supplicant.conf' > > Reading configuration file '/system/etc/wifi/wpa_supplicant.conf' > > update_config=1 > > ctrl_interface='DIR=/data/system/wpa_supplicant/ GROUP=system' > > eapol_version=1 > > ap_scan=1 > > fast_reauth=1 > > Initializing interface (2) 'wlan0' > > EAPOL: SUPP_PAE entering state DISCONNECTED > > EAPOL: KEY_RX entering state NO_KEY_RECEIVE > > EAPOL: SUPP_BE entering state INITIALIZE > > EAP: EAP entering state DISABLED > > EAPOL: External notification - portEnabled=0 > > EAPOL: External notification - portValid=0 > > SIOCGIWRANGE: WE(compiled)=22 WE(source)=21 enc_capa=0xf > > capabilities: key_mgmt 0xf enc 0xf > > WEXT: Operstate: linkmode=1, operstate=5 > > Own MAC address: 00:22:43:2c:fa:a6 > > wpa_driver_wext_set_wpa > > wpa_driver_wext_set_key: alg=0 key_idx=0 set_tx=0 seq_len=0 key_len=0 > > wpa_driver_wext_set_key: alg=0 key_idx=1 set_tx=0 seq_len=0 key_len=0 > > wpa_driver_wext_set_key: alg=0 key_idx=2 set_tx=0 seq_len=0 key_len=0 > > wpa_driver_wext_set_key: alg=0 key_idx=3 set_tx=0 seq_len=0 key_len=0 > > wpa_driver_wext_set_countermeasures > > ioctl[SIOCSIWAUTH]: Operation not supported on transport endpoint > > WEXT auth param 4 value 0x0 - wpa_driver_wext_set_drop_unencrypted > > Setting scan request: 0 sec 100000 usec > > ctrl_interface_group=1000 (from group name 'system') > > Added interface wlan0 > > RTM_NEWLINK: operstate=0 ifi_flags=0x1002 () > > RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added > > Wireless event: cmd=0x8b06 len=8 > > Ignore event for foreign ifindex 4 > > RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP]) > > RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added > > State: DISCONNECTED -> SCANNING > > CTRL-EVENT-STATE-CHANGE id=-1 state=2 > > Starting AP scan (broadcast SSID) > > Trying to get current scan results first without requesting a new scan > > to > > speed > > up initial association > > Received 0 bytes of scan results (0 BSSes) > > Scan results: 0 > > CTRL-EVENT-SCAN-RESULTS Ready > > Hi, test you wifi connection using the wpa_cli program. The parse > function of the > scan result expect a - to the signal stregh (if I remember) to parse the > result, otherwise > fail. > > wpa_cli has an interractive mode to operate, and you can send command like: > scan and scan-results. > > > No suitable AP found. > > Setting scan request: 0 sec 0 usec > > No enabled networks - do not scan > > State: SCANNING -> INACTIVE > > CTRL-EVENT-STATE-CHANGE id=-1 state=1 > > > On 27 mrt, 11:39, Androidphan <niels.kee...@tass.nl> wrote: > > >> I'm getting the following error at the moment: > >> D/WifiHW ( 2325): Unable to open connection to supplicant on "/data/ > >> system/wpa_supplicant/wlan0": No such file or directory > > >> I got wpa_supplicant running. > > >> # ls -l /data/system/wpa_supplicant/ > >> srwxrwx--- root system 2009-03-27 11:39 wlan0 > > >> So it exists. > > >> Why is this?? > > Regards Michael --~--~---------~--~----~------------~-------~--~----~ unsubscribe: android-porting+unsubscr...@googlegroups.com website: http://groups.google.com/group/android-porting -~----------~----~----~----~------~----~------~--~---