Lonnie, These tips helped me make a lot of progress. On the remote system with the TDM card, "dahdi show status" is recognizing the card. However, my local system with the Sangoma board is still a problem. My concern is the message "wanpipe1: Error: TDM VOICE prot not compiled" reported by dmesg (see below). Is it possible that there is some required component of wanpipe that was left out of the 0.7 build I am testing?
pbx ~ # dmesg | grep wanpipe wanpipe1: Running post initialization... wanpipe1: Remora config done! wanpipe1: AFT Data Mux Bit Map: 0x01234567 wanpipe1: Front End Interface Ready 0x00000000 wanpipe1: Register EC interface wanec1 (usage 1, max ec chans 32)! wanpipe1: Configuring Device :wanpipe1 FrmVr=11 wanpipe1: Global MTU = 1500 wanpipe1: Global MRU = 1500 wanpipe1: Data Mux Map = 0x01234567 wanpipe1: Rx CRC Bytes = 0 wanpipe1: Global TDM Int = Disabled wanpipe1: Global TDM Ring = Disabled wanpipe1: TDMV HW DTMF/FAX = Enabled/Disabled(0) wanpipe1: TDMV Span = 1 : Enabled wanpipe1: RTP TAP = Disabled wanpipe1: Error: TDM VOICE prot not compiled wanpipe1: during installation process! wanpipe1: Shutting Down! wanpipe1: TASKQ Not Running wanpipe1: Unconfiguring FXS/FXO Front End... wanpipe1: AFT communications disabled! (Dev Cnt: 1 Cause: Device Down) wanpipe1: Unregister interface from wanec1 (usage 1)! wanpipe1: AFT communications disabled! (Dev Cnt: 1 Cause: Device Down) wanpipe1: Global Chip Shutdown Usage=1 wanpipe1: Unconfiguring FXS/FXO Front End... wanpipe1: Master shutting down af_wanpipe: Unregistering Wanpipe API Socket Module wanpipe: WANPIPE Modules Unloaded. pbx ~ # -----Original Message----- From: Lonnie Abelbeck [mailto:[email protected]] Sent: Sunday, November 15, 2009 2:51 PM To: AstLinux Users Mailing List Subject: Re: [Astlinux-users] Astlinux-0.7 Upgrade? Tom, DAHDI files should be located as /mnt/kd/dahdi/*.conf A reboot is required for DAHDI to see them. Also, after such files are created, they may be edited via the Edit tab. While this is painful, clearly DAHDI is the future, and the transition from ZAPTEL needs to occur. Lonnie On Nov 15, 2009, at 1:28 PM, Tom Mazzotta wrote: > Correction to my last post, I copied zapata.conf to chan_dahdi.conf. > > I also tested my remote system which contains a TDM400P and it logs the same > dahdi warnings/errors, which leads me to believe that my problem has more to > do with the dahdi configuration. In doing more Google searching, it seems > like I need a system.conf under a dahdi directory. Apparently the recommended > technique to create this file is via dahdi_genconf, which I believe will not > run because it requires a full Perl implementation. I did find a sample > online which I should be able to mod for my config, however, on my box this > file is located under /stat/etc/dahdi. Now I typically have only edited files > under /mnt/kd, so I hesitate to modify this file. Should I configure the > system.conf in /stat/etc/dahdi or should it be put in another place? Or am I > on the wrong track here?? > > And since this is the first time that I am configuring dahdi, what are the > files (and their locations) that need to be configured? > > Lastly, my sincere apologies for rambling on with this post. And I very much > appreciate everyone's support with this issue. > > -----Original Message----- > From: Tom Mazzotta [mailto:[email protected]] > Sent: Sunday, November 15, 2009 1:03 PM > To: AstLinux Users Mailing List > Subject: Re: [Astlinux-users] Astlinux-0.7 Upgrade? > > I thought that was the case. One thing I did try doing was to cp my > zaptel.conf to chan_dahdi.conf. I'm sure that at least part of the problem > was that I didn't have dahdi configured. However, after doing that dahdi is > still not functional so I'm back on 0.6.8: > > Nov 15 12:46:57 pbx local0.warn asterisk[1979]: WARNING[1979]: > chan_dahdi.c:1233 in dahdi_open: Unable to specify channel 1: No such device > or address > Nov 15 12:46:57 pbx local0.err asterisk[1979]: ERROR[1979]: chan_dahdi.c:7669 > in mkintf: Unable to open channel 1: No such device or address here = 0, > tmp->channel = 1, channel = 1 > Nov 15 12:46:57 pbx local0.err asterisk[1979]: ERROR[1979]: > chan_dahdi.c:11298 in build_channels: Unable to register channel '1' > > -----Original Message----- > From: Darrick Hartman [mailto:[email protected]] > Sent: Sunday, November 15, 2009 11:06 AM > To: AstLinux Users Mailing List > Subject: Re: [Astlinux-users] Astlinux-0.7 Upgrade? > > As I recall wancfg requires several perl modules. The config files must > be hand-generated as it's not feasible for us to include more than > 'mini-perl' in AstLinux. > > > > Tom Mazzotta wrote: >> This may be the problem. However with my original 0.6 system I needed to >> prepare the wanpipe1.conf file off line because wancfg wouldn't run with >> astlinux. The sangoma site says to run /usr/sbin/wancfg_dahdi, will I have >> the same problems with wancfg under 0.7, or has that problem been fixed? As >> I mentioned previously, my zaptel version of wanpipe1 was produced when I >> ran FreeBSD on the net5501 (which I have since abandoned for various >> reasons). How can I produce a dahdi version if 0.7 hasn't resolved the >> issues running wancfg? Granted, this info is only a text file, so if I knew >> what needed to be in the file for it to work, I'm happy to hand edit it. >> >> -tm >> >> -----Original Message----- >> From: Lonnie Abelbeck [mailto:[email protected]] >> Sent: Sunday, November 15, 2009 7:28 AM >> To: AstLinux Users Mailing List >> Subject: Re: [Astlinux-users] Astlinux-0.7 Upgrade? >> >> Anyone? could Tom's Sangoma issue be a wanpipe - DAHDI issue, since 0.7 is >> built using DAHDI ? >> >> Tom, possibly your wanpipe1.conf needs to be changed reconfigured for DAHDI ? >> >> 0.7 uses wanpipe version 3.4.4 >> >> Lonnie >> >> >> On Nov 14, 2009, at 11:26 PM, Darrick Hartman wrote: >> >>> Tom, >>> >>> Do you happen to have a spare Sangoma board and a spare system that we >>> could get someone to connect in to? There are some changes between 0.6 >>> and 0.7 with the Sangoma code. I really haven't used any of their >>> hardware, but second hand from Philip, their package is a bit >>> 'convoluted' compared to most. >>> >>> I'm swamped this weekend with a server migration, but perhaps some of >>> the other users who actually have Sangoma boards would be able to >>> provide some additional information. >>> >>> Darrick >>> >>> Tom Mazzotta wrote: >>>> After reverting back to 0.6.8 I can confirm that 0.7 definitely has a >>>> problem with Sangoma support. Now "wanrouter status" reports the board as >>>> "connected" and I see a "wag1" i/f using ifconfig. And most importantly, >>>> my FXO/FXS based channels all appear to be working normally again. >>>> >>>> Let me know if there is something you would like me to test to help >>>> resolve the problem. I'm assuming that if I "revert to previous" the >>>> firmware will go back to 0.7. >>>> >>>> -----Original Message----- >>>> From: Tom Mazzotta [mailto:[email protected]] >>>> Sent: Saturday, November 14, 2009 6:21 PM >>>> To: AstLinux Users Mailing List >>>> Subject: Re: [Astlinux-users] Astlinux-0.7 Upgrade? >>>> >>>> Lonnie, >>>> >>>> [I'm taking the thread back onto the list] >>>> >>>> Correcting the NAT rules fixed the problem w/ Arno, at least for my local >>>> system. I will trouble shoot the remote box next. >>>> >>>> Even after correcting the f/w problem and rebooting, my Sangoma board is >>>> still disconnected: >>>> >>>> pbx ~ # wanrouter status >>>> >>>> Devices currently active: >>>> wanpipe1 >>>> >>>> >>>> Wanpipe Config: >>>> >>>> Device name | Protocol Map | Adapter | IRQ | Slot/IO | If's | CLK | Baud >>>> rate | >>>> wanpipe1 | N/A | A200/400/600| 10 | 14 | 0 | N/A | 0 >>>> | >>>> >>>> Wanrouter Status: >>>> >>>> Device name | Protocol | Station | Status | >>>> wanpipe1 | A-ANALOG | N/A | Disconnected | >>>> >>>> I should also see a wag i/f via ifconfig and I don't. Any ideas? >>>> Especially if this is a legit problem w/ the beta release, I'd like to >>>> help out anyway I can, but I do need to get the phones online in my house >>>> by tomorrow. >>>> >>>> -tm > > ------------------------------------------------------------------------------ > Let Crystal Reports handle the reporting - Free Crystal Reports 2008 30-Day > trial. Simplify your report design, integration and deployment - and focus on > what you do best, core application coding. Discover what's new with > Crystal Reports now. http://p.sf.net/sfu/bobj-july > _______________________________________________ > Astlinux-users mailing list > [email protected] > https://lists.sourceforge.net/lists/listinfo/astlinux-users > > Donations to support AstLinux are graciously accepted via PayPal to > [email protected]. > > > ------------------------------------------------------------------------------ > Let Crystal Reports handle the reporting - Free Crystal Reports 2008 30-Day > trial. Simplify your report design, integration and deployment - and focus on > what you do best, core application coding. Discover what's new with > Crystal Reports now. http://p.sf.net/sfu/bobj-july > _______________________________________________ > Astlinux-users mailing list > [email protected] > https://lists.sourceforge.net/lists/listinfo/astlinux-users > > Donations to support AstLinux are graciously accepted via PayPal to > [email protected]. > > > ------------------------------------------------------------------------------ > Let Crystal Reports handle the reporting - Free Crystal Reports 2008 30-Day > trial. Simplify your report design, integration and deployment - and focus on > what you do best, core application coding. Discover what's new with > Crystal Reports now. http://p.sf.net/sfu/bobj-july > _______________________________________________ > Astlinux-users mailing list > [email protected] > https://lists.sourceforge.net/lists/listinfo/astlinux-users > > Donations to support AstLinux are graciously accepted via PayPal to > [email protected]. > > ------------------------------------------------------------------------------ Let Crystal Reports handle the reporting - Free Crystal Reports 2008 30-Day trial. Simplify your report design, integration and deployment - and focus on what you do best, core application coding. Discover what's new with Crystal Reports now. http://p.sf.net/sfu/bobj-july _______________________________________________ Astlinux-users mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/astlinux-users Donations to support AstLinux are graciously accepted via PayPal to [email protected]. ------------------------------------------------------------------------------ Let Crystal Reports handle the reporting - Free Crystal Reports 2008 30-Day trial. Simplify your report design, integration and deployment - and focus on what you do best, core application coding. Discover what's new with Crystal Reports now. http://p.sf.net/sfu/bobj-july _______________________________________________ Astlinux-users mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/astlinux-users Donations to support AstLinux are graciously accepted via PayPal to [email protected].
