This would imply that the define "CONFIG_PRODUCT_WANPIPE_TDM_VOICE" is not set when wanpipe is build.
This is definitely a Philip question... Lonnie On Nov 15, 2009, at 3:35 PM, Tom Mazzotta wrote: > Lonnie, > > These tips helped me make a lot of progress. On the remote system with the > TDM card, "dahdi show status" is recognizing the card. However, my local > system with the Sangoma board is still a problem. My concern is the message > "wanpipe1: Error: TDM VOICE prot not compiled" reported by dmesg (see below). > Is it possible that there is some required component of wanpipe that was left > out of the 0.7 build I am testing? > > pbx ~ # dmesg | grep wanpipe > wanpipe1: Running post initialization... > wanpipe1: Remora config done! > wanpipe1: AFT Data Mux Bit Map: 0x01234567 > wanpipe1: Front End Interface Ready 0x00000000 > wanpipe1: Register EC interface wanec1 (usage 1, max ec chans 32)! > wanpipe1: Configuring Device :wanpipe1 FrmVr=11 > wanpipe1: Global MTU = 1500 > wanpipe1: Global MRU = 1500 > wanpipe1: Data Mux Map = 0x01234567 > wanpipe1: Rx CRC Bytes = 0 > wanpipe1: Global TDM Int = Disabled > wanpipe1: Global TDM Ring = Disabled > wanpipe1: TDMV HW DTMF/FAX = Enabled/Disabled(0) > wanpipe1: TDMV Span = 1 : Enabled > wanpipe1: RTP TAP = Disabled > wanpipe1: Error: TDM VOICE prot not compiled > wanpipe1: during installation process! > wanpipe1: Shutting Down! > wanpipe1: TASKQ Not Running > wanpipe1: Unconfiguring FXS/FXO Front End... > wanpipe1: AFT communications disabled! (Dev Cnt: 1 Cause: Device Down) > wanpipe1: Unregister interface from wanec1 (usage 1)! > wanpipe1: AFT communications disabled! (Dev Cnt: 1 Cause: Device Down) > wanpipe1: Global Chip Shutdown Usage=1 > wanpipe1: Unconfiguring FXS/FXO Front End... > wanpipe1: Master shutting down > af_wanpipe: Unregistering Wanpipe API Socket Module > wanpipe: WANPIPE Modules Unloaded. > pbx ~ # > > -----Original Message----- > From: Lonnie Abelbeck [mailto:[email protected]] > Sent: Sunday, November 15, 2009 2:51 PM > To: AstLinux Users Mailing List > Subject: Re: [Astlinux-users] Astlinux-0.7 Upgrade? > > Tom, > > DAHDI files should be located as /mnt/kd/dahdi/*.conf > > A reboot is required for DAHDI to see them. Also, after such files are > created, they may be edited via the Edit tab. > > While this is painful, clearly DAHDI is the future, and the transition from > ZAPTEL needs to occur. > > Lonnie ------------------------------------------------------------------------------ Let Crystal Reports handle the reporting - Free Crystal Reports 2008 30-Day trial. Simplify your report design, integration and deployment - and focus on what you do best, core application coding. Discover what's new with Crystal Reports now. http://p.sf.net/sfu/bobj-july _______________________________________________ Astlinux-users mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/astlinux-users Donations to support AstLinux are graciously accepted via PayPal to [email protected].
