Where are you pinging from and to? Post the other PE/CE router configs from the other end.
Jeff On Friday, February 1, 2013, Bodnar, Edward wrote: > Routes end to end look ok. > > -----Original Message----- > From: Jeff Andiorio [mailto:[email protected] <javascript:;>] > Sent: Friday, February 01, 2013 7:15 PM > To: Bodnar, Edward > Cc: [email protected]; [email protected] > Subject: Re: [OSL | CCIE_RS] BGP PE - CE configuration > > Same AS at the two cust sites? > Routes on CE or not? > > J > > Sent from my iPhone > > On Feb 1, 2013, at 6:51 PM, "Bodnar, Edward" <[email protected]> > wrote: > > > If I change things up and use EIGRP RIP or OSPF it works just fine. So > I > was thinking it was something with BGP. > > > > > > > > From: Steve Di Bias [mailto: <[email protected]>[email protected]] > > Sent: Friday, February 01, 2013 6:48 PM > > To: Bodnar, Edward > > Cc: [email protected] > > Subject: Re: [OSL | CCIE_RS] BGP PE - CE configuration > > > > > > > > Make sure you are advertising the loopbacks on your CE's, do you see > these > in the routing table of the other CE's? Now try pinging again but source > your packets from the loopback. > > > > > > > > From CE -"ping x.x.x.x source y.y.y.y" > > > > > > > > If you are seeing the routes on your CE's that means the RT's are > importing just fine. If that doesn't work we will dig deeper. > > > > > > > > > > > > > > > > On Fri, Feb 1, 2013 at 2:24 PM, Bodnar, Edward > <[email protected]<mailto: <[email protected]> > Edward.Bodnar@unisys. > <[email protected]>com<[email protected]>>> > wrote: > > > > I can never seem to get this to work. I can See routes end to end but I > am missing something when I use BGP as the PE - CE protocol. I thought BGP > was supposed to be the easy one J > > > > > > > > > > > > I have full connectivity. And I can see routes Just can't ping. > > > > > > > > RT4: > > > > router bgp 1 > > > > no bgp default ipv4-unicast > > > > bgp log-neighbor-changes > > > > neighbor 1.1.1.1 remote-as 1 > > > > neighbor 1.1.1.1 update-source Loopback0 > > > > neighbor 10.10.45.5 remote-as 5 > > > > ! > > > > address-family ipv4 > > > > neighbor 1.1.1.1 activate > > > > neighbor 10.10.45.5 activate > > > > no auto-summary > > > > no synchronization > > > > exit-address-family > > > > ! > > > > address-family vpnv4 > > > > neighbor 1.1.1.1 activate > > > > neighbor 1.1.1.1 send-community both > > > > exit-address-family > > > > ! > > > > address-family ipv4 vrf B > > > > neighbor 10.10.45.5 remote-as 5 > > > > neighbor 10.10.45.5 activate > > > > no synchronization > > > > exit-address-family > > > > > > > > > > > > > > > > > > > > > > > > R5(config-router)#do sh run | s bgp > > > > router bgp 5 > > > > no synchronization > > > > bgp log-neighbor-changes > > > > network 55.55.55.55 mask 255.255.255.255 > > > > neighbor 10.10.45.4 remote-as 1 > > > > no auto-summary > > > > > > > > > > > > _______________________________________________ > > For more information regarding industry leading CCIE Lab training, please > visit www.ipexpert.com<http://www.ipexpert.com> > > > > Are you a CCNP or CCIE and looking for a job? Check out > www.PlatinumPlacement.com<http://www.PlatinumPlacement.com> > > > > http://onlinestudylist.com/mailman/listinfo/ccie_rs > > > > > > > > > > > > > > > > -- > > > > Thank you, > > > > > > > > Steve Di Bias > > > > CCIE #32840 > > > > _______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com http://onlinestudylist.com/mailman/listinfo/ccie_rs
