Hi Louie
I like to make sure if I understand your solution.
The reason why it didn't make difference is that you
didn't configure in the interface configuration mode.
is that your reason?
I will appreciate your reply.
jeongwoo
--- Louie Belt <[EMAIL PROTECTED]> wrote:
> Thanks! That would explain why it never made a
> difference. Cisco's info on
> it is a bit vague. I got this from the Cisco CD:
>
> dialer enable-timeout
> To set the length of time an interface stays down
> after a call has completed
> or failed and before it is available to dial again,
> use the dialer
> enable-timeout interface configuration command. To
> return to the default
> value, use the no form of this command.
>
> dialer enable-timeout seconds
> no dialer enable-timeout
>
> Syntax Description
> seconds
> Time in seconds that the Cisco IOS software waits
> before the next call can
> occur on the specific interface. Acceptable values
> are positive, nonzero
> integers.
>
> This value must be greater than the serial pulse
> interval for this
> interface, set via the pulse-time command.
>
> Default
> 15 seconds
>
> Command Mode
> Interface configuration
>
> Usage Guidelines
> This command first appeared in Cisco IOS Release
> 10.0.
>
> This command applies to inbound and outbound calls.
>
> If your phone lines are often busy or down, you
> might want to enforce a
> certain period of time before the system repeats an
> attempt to make a
> connection with a remote site. Configuring this
> timeout can prevent outgoing
> lines and switching equipment from being needlessly
> overloaded.
>
>
> Louie
>
>
>
> -----Original Message-----
> From: [EMAIL PROTECTED]
> [mailto:[EMAIL PROTECTED]]On Behalf Of
> Mark Vicuna
> Sent: Wednesday, October 25, 2000 3:09 AM
> To: Louie Belt; [EMAIL PROTECTED]
> Subject: Re: OSPF Demand Circuit...
>
>
> Louie,
>
> dialer enable-timeout is used for callback.
>
>
> hth,
> Mark.
>
> At 12:03 AM 10/25/00 -0500, Louie Belt wrote:
> >While configuring and OSPF demand circuit over
> ISDN, I noticed that the
> ISDN
> >link would disconnected and immediately reconnect -
> because the change in
> >ospf topology was triggering and LSA flood -
> forcing the ISDN line to
> >reconnect. However, the dialer enable-timeout
> setting was at it's default
> >of 15 seconds so the ISDN link should have been
> forced to wait 15 seconds
> >before attempting to reconnect (and thereby giving
> the LSA flood time to
> >pass). However, this did not happen. No matter
> what I set the dialer
> >enable-timeout to, the redial happened immediately.
> >
> >Question: What am I missing? (or
> mis-understanding)
> >
> >Thanks in advance!
> >
> >Louie
> >
> >
> >
> >
> >
> >
> >_________________________________
> >FAQ, list archives, and subscription info:
> >http://www.groupstudy.com/list/cisco.html
> >Report misconduct and Nondisclosure violations to
> [EMAIL PROTECTED]
>
> _________________________________
> FAQ, list archives, and subscription info:
> http://www.groupstudy.com/list/cisco.html
> Report misconduct and Nondisclosure violations to
> [EMAIL PROTECTED]
>
> _________________________________
> FAQ, list archives, and subscription info:
> http://www.groupstudy.com/list/cisco.html
> Report misconduct and Nondisclosure violations to
[EMAIL PROTECTED]
__________________________________________________
Do You Yahoo!?
Yahoo! Messenger - Talk while you surf! It's FREE.
http://im.yahoo.com/
_________________________________
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
