SAE_ZUR_NAT>sho int token 1
TokenRing1 is up, line protocol is up
Hardware is TMS380, address is 0000.3060.0e5b (bia 0000.3060.0e5b)
Description: Token-Ring to SITA
Internet address is 10.60.0.2/16
MTU 4464 bytes, BW 16000 Kbit, DLY 630 usec, rely 255/255, load 1/255
Encapsulation SNAP, loopback not set, keepalive set (10 sec)
ARP type: SNAP, ARP Timeout 04:00:00
Ring speed: 16 Mbps
Single ring node, Source Route Transparent Bridge capable
Group Address: 0x00000000, Functional Address: 0x08000000
Ethernet Transit OUI: 0x000000
Last input 00:00:02, output 00:00:00, output hang never
Last clearing of "show interface" counters never
Queueing strategy: fifo
Output queue 0/40, 0 drops; input queue 0/75, 0 drops
5 minute input rate 2000 bits/sec, 1 packets/sec
5 minute output rate 3000 bits/sec, 2 packets/sec
96719 packets input, 31535696 bytes, 0 no buffer
Received 71898 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
127859 packets output, 26608784 bytes, 0 underruns
0 output errors, 0 collisions, 2 interface resets
0 output buffer failures, 0 output buffers swapped out
6 transitions
SAE_ZUR_NAT>
-----Original Message-----
From: Sam LI [mailto:[EMAIL PROTECTED]]
Sent: 01 November 2000 18:40
To: Andrew Larkins; Cisco Mail List
Subject: Re: EIGRP Neighbour - keeps flapping
we need the output of
"show int tok 0"
and
check the "Keepalive" too
Sam Li
----- Original Message -----
From: Andrew Larkins <[EMAIL PROTECTED]>
To: Cisco Mail List <[EMAIL PROTECTED]>
Sent: Wednesday, November 01, 2000 4:18 PM
Subject: EIGRP Neighbour - keeps flapping
> HI all,
>
> I have to routers connected on a token ring segment. Every 120seconds
> exactly they lose the neighbourship. This is then established immediately
> but keeps flapping. There have been no changes to the default EIGRP config
> here in relation to timers.
>
> Any idea's????
>
>
> Andrew Larkins
> BCom, CCNA, CCDA
> Usko Communications
> Tel: +2711 800-9300
> Fax: +2711 800-9495/6/7/8/9
> Cell: +2783-656-7214
> Email: [EMAIL PROTECTED]
> OR [EMAIL PROTECTED]
>
>
> "This message may contain information which is confidential and subject to
> legal privilege. If you are not the intended recipient, you may not
peruse,
> use, disseminate, distribute or copy this message. If you have received
> this message in error, please notify the sender immediately by email,
> facsimile or telephone and return and/or destroy the original message."
>
>
> _________________________________
> FAQ, list archives, and subscription info:
http://www.groupstudy.com/list/cisco.html
> Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
_________________________________
FAQ, list archives, and subscription info:
http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
_________________________________
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
