The version 2 WIC commands are all identical this WIC just has an upgraded framer and some other hardware.
What exactly are you trying to do?? Dave Simmi Singh wrote: > Hi Dave > Thanx replying > is this in version 2 of WIC-1DSU-T1 these commands work fine or what I > could not get u. > May be somebody else who has worked on WIC-1DSU-T1,please do send your > valuable comments if u have any. > > > > MADMAN wrote: > >>The documentation is not very accurate on this as you have >>discovered. Thanks for pointing this out, I am beta testing >>a version >>2 of the WIC-1DSU-T1 and it is not optional, I will pass this >>on. >> >> Aside from testing though I have never needed to change the >>default >>in the real world. The defaults let you loop the CSU with a >>standard >>issue T-BERD. >> >> Dave >> >>Simmi Singh wrote: >> >>>I have 1 Port T1 CSU/DSU WAN Interface Card, >>>some more problems I am facing are >>>1) when I am trying to give >>>service-module t1 remote-loopback payload command with out >> >>any optional >> >>>parameter it does not work and gives that incomplete command >> >>error.where as >> >>>the V54 is optional parameter >>> >>>2) this combination of command also does not work and gives >> >>format error. >> >>>service-module t1 remote-loopback full alternate >>> >>>this both v54 and alternate are optional parameters as >> >>mentioned in the >> >>>documentation. >>> >>> >> > http://www.cisco.com/en/US/products/sw/iosswrel/ps1835/products_command_reference_chapter09186a00800874e6.html#1019309 > >>>Please refer this link that these are optional parameters(v54 >> >>and >> >>>alternate). >>>In my knowledge there could be 4 possible combinations but >> >>only two work >> >>>full >>>full with alternate(doesnot work) >>>payload(doesnot work) >>>payload with v54 >>> >>>Can anybody explain these also in additional to the previous >> >>doubts >> >>>mentioned below >>>--------------------------------------------------- >>> >>> >>>Simmi Singh wrote: >>> >>> >>>>Hi all, >>>>while configuring the T1 CSU DSU card we use service-module >>>>commands. >>>>Here when I have the following command >>>>service-module t1 remote-loopback {full | payload} [alternate >>> >>| >> >>>>v54] >>>>The default option is Full and payload loopbacks with >>>>standard-loopup codes. and its mentioned in documentation >>> >>also >> >>>>that by entering the service-module t1 remote-loopback >>> >>command >> >>>>without specifying any keywords, you enable the >>> >>standard-loopup >> >>>>codes, which use a 1-in-5 pattern for loopup and a 1-in-3 >>>>pattern for loopdown. >>>> >>>> >>>>The calrifications needed are that >>>>1) What is thedefault option for loopback.If I select the >>> >>full option from >> >>>the cli then want to switch >>> >>> >>>>back to the default option, do the above command without >>>>parameters will do that function >>>>example >>>>service-module t1 remote-loopback full alternate >>>> >>>> >>>>then if i want to switch to default option will this work >>>> >>>>service-module t1 remote-loopback >>>> >>>>But I tried this command doesnot work(incomplete command) >>>>so how to enable both payload and alternate with standard >>>>loopup codes. >>>>Just by negating the earlier command >>>>is their some command for this >>>> >>>>2) For what this default option used for >>>> >>>>any help will be appreciated >>> >>-- >>David Madland >>CCIE# 2016 >>Sr. Network Engineer >>Qwest Communications >>612-664-3367 >> >>"You don't make the poor richer by making the rich poorer." >>--Winston >>Churchill -- David Madland CCIE# 2016 Sr. Network Engineer Qwest Communications 612-664-3367 "You don't make the poor richer by making the rich poorer." --Winston Churchill Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=62580&t=62445 -------------------------------------------------- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
