I talked With a DE and they are aware of the documentation error and I was told that it has been corrected in the V2 docs. When that will be reflected online is anybodys guess!!
Dave Simmi Singh wrote: > Hi Dave, > I was just trying installing and confguring T1 card and I found the > commands wrong & not working as per documentation. > Thats why i was confuse and i thought I was wrong somewhere. > thanx for clarification > But has no body else observed what me and dave observed about t1 card. > (The commands which are not working) > > MADMAN wrote: > >>The version 2 WIC commands are all identical this WIC just has >>an >>upgraded framer and some other hardware. >> >> What exactly are you trying to do?? >> >> Dave >> >>Simmi Singh wrote: >> >>>Hi Dave >>>Thanx replying >>>is this in version 2 of WIC-1DSU-T1 these commands work fine >> >>or what I >> >>>could not get u. >>>May be somebody else who has worked on WIC-1DSU-T1,please do >> >>send your >> >>>valuable comments if u have any. >>> >>> >>> >>>MADMAN wrote: >>> >>> >>>>The documentation is not very accurate on this as you have >>>>discovered. Thanks for pointing this out, I am beta testing >>>>a version >>>>2 of the WIC-1DSU-T1 and it is not optional, I will pass this >>>>on. >>>> >>>> Aside from testing though I have never needed to change the >>>>default >>>>in the real world. The defaults let you loop the CSU with a >>>>standard >>>>issue T-BERD. >>>> >>>> Dave >>>> >>>>Simmi Singh wrote: >>>> >>>> >>>>>I have 1 Port T1 CSU/DSU WAN Interface Card, >>>>>some more problems I am facing are >>>>>1) when I am trying to give >>>>>service-module t1 remote-loopback payload command with out >>>> >>>>any optional >>>> >>>> >>>>>parameter it does not work and gives that incomplete command >>>> >>>>error.where as >>>> >>>> >>>>>the V54 is optional parameter >>>>> >>>>>2) this combination of command also does not work and gives >>>> >>>>format error. >>>> >>>> >>>>>service-module t1 remote-loopback full alternate >>>>> >>>>>this both v54 and alternate are optional parameters as >>>> >>>>mentioned in the >>>> >>>> >>>>>documentation. >>>>> >>>>> >>>> > http://www.cisco.com/en/US/products/sw/iosswrel/ps1835/products_command_reference_chapter09186a00800874e6.html#1019309 > >>>>>Please refer this link that these are optional parameters(v54 >>>> >>>>and >>>> >>>> >>>>>alternate). >>>>>In my knowledge there could be 4 possible combinations but >>>> >>>>only two work >>>> >>>> >>>>>full >>>>>full with alternate(doesnot work) >>>>>payload(doesnot work) >>>>>payload with v54 >>>>> >>>>>Can anybody explain these also in additional to the previous >>>> >>>>doubts >>>> >>>> >>>>>mentioned below >>>>>--------------------------------------------------- >>>>> >>>>> >>>>>Simmi Singh wrote: >>>>> >>>>> >>>>> >>>>>>Hi all, >>>>>>while configuring the T1 CSU DSU card we use service-module >>>>>>commands. >>>>>>Here when I have the following command >>>>>>service-module t1 remote-loopback {full | payload} >>>>> >>[alternate >> >>>>| >>>> >>>> >>>>>>v54] >>>>>>The default option is Full and payload loopbacks with >>>>>>standard-loopup codes. and its mentioned in documentation >>>>> >>>>also >>>> >>>> >>>>>>that by entering the service-module t1 remote-loopback >>>>> >>>>command >>>> >>>> >>>>>>without specifying any keywords, you enable the >>>>> >>>>standard-loopup >>>> >>>> >>>>>>codes, which use a 1-in-5 pattern for loopup and a 1-in-3 >>>>>>pattern for loopdown. >>>>>> >>>>>> >>>>>>The calrifications needed are that >>>>>>1) What is thedefault option for loopback.If I select the >>>>> >>>>full option from >>>> >>>> >>>>>the cli then want to switch >>>>> >>>>> >>>>> >>>>>>back to the default option, do the above command without >>>>>>parameters will do that function >>>>>>example >>>>>>service-module t1 remote-loopback full alternate >>>>>> >>>>>> >>>>>>then if i want to switch to default option will this work >>>>>> >>>>>>service-module t1 remote-loopback >>>>>> >>>>>>But I tried this command doesnot work(incomplete command) >>>>>>so how to enable both payload and alternate with standard >>>>>>loopup codes. >>>>>>Just by negating the earlier command >>>>>>is their some command for this >>>>>> >>>>>>2) For what this default option used for >>>>>> >>>>>>any help will be appreciated >>>>> >>>>-- >>>>David Madland >>>>CCIE# 2016 >>>>Sr. Network Engineer >>>>Qwest Communications >>>>612-664-3367 >>>> >>>>"You don't make the poor richer by making the rich poorer." >>>>--Winston >>>>Churchill >>> >>-- >>David Madland >>CCIE# 2016 >>Sr. Network Engineer >>Qwest Communications >>612-664-3367 >> >>"You don't make the poor richer by making the rich poorer." >>--Winston >>Churchill -- David Madland CCIE# 2016 Sr. Network Engineer Qwest Communications 612-664-3367 "You don't make the poor richer by making the rich poorer." --Winston Churchill Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=62638&t=62445 -------------------------------------------------- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]