Not necessarily the case for basic-net3 switch type. I have seen basic rate ETSI interfaces actuallly appear to be dead - at L1 as well as L2. Put a call through and up it comes. Pain in the neck, because you can't tell if the service is cactus without actually making a call. If anyone has any solutions do let me know :-)
JMcL Troy Leliard wrote: > > You should definatley be getting output from debug isdn Q921 . > This in effect is the D=Channel connectivity to the ISDN > switch, and should always be up. If you are not getting SPI's > when you debug this, then there is definatley a connectivity > issue between your router and the ISDN switch? You also didn't > mention where you are ? This could have an impact on the > requirement of specifying your SPID's ? > > > > > > > > have u generated interesting traffic? ping to remote site. > > > > ----- Original Message ----- > > From: "Johan Bornman" > > To: > > Sent: Thursday, March 13, 2003 11:52 PM > > Subject: ISDN Config Problem? [7:65315] > > > > > > > I am having difficulty getting my Cisco 803 to dial out the > > BRI interface. > > > If I run the debug > > > commands: isdn q921 and q931 with the debug ppp > > authentication commands, > > > nothing happens. I have > > > also tried different configurations but I get the same from > > the > > > router.....nothing. Term mon is > > > enabled! The isdn status command shows the line as active or > > activated, so > > > there is no problem with > > > the line. I have tried the router on different ISDN lines to > > be sure. > > > > > > How do I check if my BRI interface is working? > > > > > > Any feedback/suggestions will be appreciated. > > > > > > Regards > > > > > > Johan > > > > > > > > > > > > Here is my config: (I have x'd out the username, password > and > > dialer > > string > > > number) > > > > > > CSTM#sh run > > > Building configuration... > > > > > > Current configuration : 1020 bytes > > > ! > > > version 12.1 > > > no service pad > > > service timestamps debug uptime > > > service timestamps log uptime > > > no service password-encryption > > > ! > > > hostname CSTM > > > ! > > > enable secret 5 $1$9Y0j$fCPvbvNR8L37mwYBtD66K0 > > > ! > > > ip subnet-zero > > > ! > > > no ip domain-lookup > > > no ip finger > > > isdn switch-type basic-net3 > > > ! > > > interface Ethernet0 > > > ip address 192.168.3.250 255.255.255.0 > > > ip nat inside > > > ! > > > interface BRI0 > > > no ip address > > > ip nat outside > > > encapsulation ppp > > > dialer pool-member 1 > > > isdn switch-type basic-net3 > > > no cdp enable > > > ! > > > interface Dialer0 > > > ip address negotiated > > > encapsulation ppp > > > dialer pool 1 > > > dialer idle-timeout 300 > > > dialer string XXXXXXXXXXX > > > dialer load-threshold 128 outbound > > > dialer-group 1 > > > ppp pap sent-username XXXXXXXXXX password 7 XXXXXXXXXXXXX > > > ! > > > ip nat inside source list 1 interface BRI0 overload > > > no ip http server > > > ip classless > > > ip route 0.0.0.0 0.0.0.0 Dialer0 > > > ! > > > access-list 1 permit 0.0.0.0 255.255.255.0 > > > dialer-list 1 protocol ip permit > > > ! > > > line con 0 > > > transport input none > > > stopbits 1 > > > line vty 0 4 > > > password cstm > > > login > > > ! > > > > Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=65618&t=65315 -------------------------------------------------- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
