On Fri, 23 May 2014, a k wrote: > Date: Fri, 23 May 2014 04:16:59 -0700 > From: a k <pccncmach...@gmail.com> > Reply-To: "Enhanced Machine Controller (EMC)" > <emc-users@lists.sourceforge.net> > To: "Enhanced Machine Controller (EMC)" <emc-users@lists.sourceforge.net> > Subject: Re: [Emc-users] emc2--2.5 > > hi > i think that the situation where i am now - controller that does not work- > is good answer to question why i avoid to update to new releases of emc2. > > > why data for 5i20 was change during evaluation from 2.25 to 2.5? -it was > working on emc2 2.25 just keep it same. > > so my board 5i20 is useless now - garbage? > i have 2 of them!
The 5I20 is unchanged and you can go back to 2.2.5 easily if you saved you 2.2.5 installation The 5I20s that you have are old enough that they may need to have their EEPROM data updated to the current to be able to rum Hostmot2 firmware, but this is not clear because At one point you showed an error that indicated a card access problem (FPGA reset issue) but then you said that you were able to launch linuxCNC What is the curret situation with running linuxcnc 2.5? Q > > > > On Thu, May 22, 2014 at 2:23 PM, a k <pccncmach...@gmail.com> wrote: > >> what should i do now? >> there was reason that i like emc2.2 >> >> >> On Thu, May 22, 2014 at 12:15 PM, Peter C. Wallace <p...@mesanet.com>wrote: >> >>> On Thu, 22 May 2014, a k wrote: >>> >>>> Date: Thu, 22 May 2014 11:32:08 -0700 >>>> From: a k <pccncmach...@gmail.com> >>>> Reply-To: "Enhanced Machine Controller (EMC)" >>>> <emc-users@lists.sourceforge.net> >>>> To: "Enhanced Machine Controller (EMC)" < >>> emc-users@lists.sourceforge.net> >>>> Subject: Re: [Emc-users] emc2--2.5 >>>> >>>> i think i know >>>> >>>> >>>> On Thu, May 22, 2014 at 11:29 AM, a k <pccncmach...@gmail.com> wrote: >>>> >>>>> who is PCW? >>>>> >>>>> >>>>> On Thu, May 22, 2014 at 11:18 AM, andy pugh <bodge...@gmail.com> >>> wrote: >>>>> >>>>>> On 22 May 2014 19:06, a k <pccncmach...@gmail.com> wrote: >>>>>>> [11380.125103] hm2_5i20.0: firmware: requesting hm2/5i20/SVST8_4.BIT >>>>>>> [11380.127460] hm2_5i20.0: FPGA did not reset: /INIT = 1, DONE = 1 >>>>>> >>>>>> OK, so you seem to have a config updated for the new driver, which is >>>>>> a good start. >>>>>> I think we might need PCW to explain the problem above. >>>>>> >>> >>> >>> Not sure (especialliy if linuxCNC does load with drivers disabled) >>> >>> that error by itself may indicate very old EEPROM data on the 5I20 >>> >>> >>>>>> >>>>>> -- >>>>>> atp >>>>>> If you can't fix it, you don't own it. >>>>>> http://www.ifixit.com/Manifesto >>>>>> >>>>>> >>>>>> >>> ------------------------------------------------------------------------------ >>>>>> "Accelerate Dev Cycles with Automated Cross-Browser Testing - For FREE >>>>>> Instantly run your Selenium tests across 300+ browser/OS combos. >>>>>> Get unparalleled scalability from the best Selenium testing platform >>>>>> available >>>>>> Simple to use. Nothing to install. Get started now for free." >>>>>> http://p.sf.net/sfu/SauceLabs >>>>>> _______________________________________________ >>>>>> Emc-users mailing list >>>>>> Emc-users@lists.sourceforge.net >>>>>> https://lists.sourceforge.net/lists/listinfo/emc-users >>>>>> >>>>> >>>>> >>>> >>> ------------------------------------------------------------------------------ >>>> "Accelerate Dev Cycles with Automated Cross-Browser Testing - For FREE >>>> Instantly run your Selenium tests across 300+ browser/OS combos. >>>> Get unparalleled scalability from the best Selenium testing platform >>> available >>>> Simple to use. Nothing to install. Get started now for free." >>>> http://p.sf.net/sfu/SauceLabs >>>> _______________________________________________ >>>> Emc-users mailing list >>>> Emc-users@lists.sourceforge.net >>>> https://lists.sourceforge.net/lists/listinfo/emc-users >>>> >>> >>> Peter Wallace >>> Mesa Electronics >>> >>> (\__/) >>> (='.'=) This is Bunny. Copy and paste bunny into your >>> (")_(") signature to help him gain world domination. >>> >>> >>> >>> ------------------------------------------------------------------------------ >>> "Accelerate Dev Cycles with Automated Cross-Browser Testing - For FREE >>> Instantly run your Selenium tests across 300+ browser/OS combos. >>> Get unparalleled scalability from the best Selenium testing platform >>> available >>> Simple to use. Nothing to install. Get started now for free." >>> http://p.sf.net/sfu/SauceLabs >>> _______________________________________________ >>> Emc-users mailing list >>> Emc-users@lists.sourceforge.net >>> https://lists.sourceforge.net/lists/listinfo/emc-users >>> >> >> > ------------------------------------------------------------------------------ > "Accelerate Dev Cycles with Automated Cross-Browser Testing - For FREE > Instantly run your Selenium tests across 300+ browser/OS combos. > Get unparalleled scalability from the best Selenium testing platform available > Simple to use. Nothing to install. Get started now for free." > http://p.sf.net/sfu/SauceLabs > _______________________________________________ > Emc-users mailing list > Emc-users@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/emc-users > Peter Wallace Mesa Electronics (\__/) (='.'=) This is Bunny. Copy and paste bunny into your (")_(") signature to help him gain world domination. ------------------------------------------------------------------------------ "Accelerate Dev Cycles with Automated Cross-Browser Testing - For FREE Instantly run your Selenium tests across 300+ browser/OS combos. Get unparalleled scalability from the best Selenium testing platform available Simple to use. Nothing to install. Get started now for free." http://p.sf.net/sfu/SauceLabs _______________________________________________ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users
