I can get it to do it in a freshly built 2.9.0~pre0 - doesn't seem to do it in 2.8.2
rtapi_app: caught signal 8 - dumping core exiting linuxcnc gets you Shutting down and cleaning up LinuxCNC... task: 2145 cycles, min=0.000007, max=0.013650, avg=0.009993, 0 latency excursions (> 10x expected cycle time of 0.010000s) USRMOT: ERROR: command timeout Waited 3 seconds for master. giving up. Note: Using POSIX realtime pwmgen: not loaded <commandline>:0: exit value: 255 <commandline>:0: rmmod failed, returned -1 Note: Using POSIX realtime lowpass: not loaded <commandline>:0: exit value: 255 <commandline>:0: rmmod failed, returned -1 Note: Using POSIX realtime scale: not loaded <commandline>:0: exit value: 255 <commandline>:0: rmmod failed, returned -1 Note: Using POSIX realtime abs: not loaded <commandline>:0: exit value: 255 <commandline>:0: rmmod failed, returned -1 Note: Using POSIX realtime encoder: not loaded <commandline>:0: exit value: 255 <commandline>:0: rmmod failed, returned -1 Note: Using POSIX realtime stepgen: not loaded <commandline>:0: exit value: 255 <commandline>:0: rmmod failed, returned -1 Note: Using POSIX realtime hal_parport: not loaded <commandline>:0: exit value: 255 <commandline>:0: rmmod failed, returned -1 Note: Using POSIX realtime motmod: not loaded <commandline>:0: exit value: 255 <commandline>:0: rmmod failed, returned -1 Note: Using POSIX realtime trivkins: not loaded <commandline>:0: exit value: 255 <commandline>:0: rmmod failed, returned -1 Note: Using POSIX realtime homemod: not loaded <commandline>:0: exit value: 255 <commandline>:0: rmmod failed, returned -1 Note: Using POSIX realtime tpmod: not loaded <commandline>:0: exit value: 255 <commandline>:0: rmmod failed, returned -1 <commandline>:0: unloadrt failed Note: Using POSIX realtime On Thu, Sep 1, 2022 at 10:42 PM Sam Sokolik <samco...@gmail.com> wrote: > Bary - Could we get all the files? > custompanel.xml > postgui_call_list.hal > custom.hal > > I just built RIP on buster and ran the config (remarking out the missing > files) > I have an encoder in pin 10 and 11 and it seems to work with no crash. > > sam > > > On Thu, Sep 1, 2022 at 9:45 PM Bari <bari00...@gmail.com> wrote: > >> Brand new setup using stepconf. if I spin the spindle encoder quickly >> by hand I get: rtapi_app: caught signal 8 - dumping core >> >> Even if the machine is still in e-stop. Simple config using stepconf >> LINUXCNC - 2.9.0~pre0 >> >> All default settings other than manual edit of LPT base address and >> changed setp encoder.0.position-scale 4000.000000 Default is like >> 100 vs 4000 >> >> Any ideas what causes this error? >> >> https://forum.linuxcnc.org/media/kunena/attachments/1324/simple.ini >> >> https://forum.linuxcnc.org/media/kunena/attachments/1324/simple.hal >> >> The only mention of a similar error: >> forum.linuxcnc.org/24-hal-components/358...hercat-lcec?start=10 >> >> >> >> _______________________________________________ >> Emc-users mailing list >> Emc-users@lists.sourceforge.net >> https://lists.sourceforge.net/lists/listinfo/emc-users >> > _______________________________________________ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users
