oh - I think we are both running buster too... (it happens with just those to files (ini and hal) when spinning an encoder hooked to pin 10 and 11 of the printer port. (happens pretty quick)
sam On Thu, Sep 1, 2022 at 11:25 PM Sam Sokolik <samco...@gmail.com> wrote: > I can get it to do it in a freshly built 2.9.0~pre0 - doesn't seem to do > it in 2.8.2 > > rtapi_app: caught signal 8 - dumping core > > exiting linuxcnc gets you > Shutting down and cleaning up LinuxCNC... > task: 2145 cycles, min=0.000007, max=0.013650, avg=0.009993, 0 latency > excursions (> 10x expected cycle time of 0.010000s) > USRMOT: ERROR: command timeout > Waited 3 seconds for master. giving up. > Note: Using POSIX realtime > pwmgen: not loaded > <commandline>:0: exit value: 255 > <commandline>:0: rmmod failed, returned -1 > Note: Using POSIX realtime > lowpass: not loaded > <commandline>:0: exit value: 255 > <commandline>:0: rmmod failed, returned -1 > Note: Using POSIX realtime > scale: not loaded > <commandline>:0: exit value: 255 > <commandline>:0: rmmod failed, returned -1 > Note: Using POSIX realtime > abs: not loaded > <commandline>:0: exit value: 255 > <commandline>:0: rmmod failed, returned -1 > Note: Using POSIX realtime > encoder: not loaded > <commandline>:0: exit value: 255 > <commandline>:0: rmmod failed, returned -1 > Note: Using POSIX realtime > stepgen: not loaded > <commandline>:0: exit value: 255 > <commandline>:0: rmmod failed, returned -1 > Note: Using POSIX realtime > hal_parport: not loaded > <commandline>:0: exit value: 255 > <commandline>:0: rmmod failed, returned -1 > Note: Using POSIX realtime > motmod: not loaded > <commandline>:0: exit value: 255 > <commandline>:0: rmmod failed, returned -1 > Note: Using POSIX realtime > trivkins: not loaded > <commandline>:0: exit value: 255 > <commandline>:0: rmmod failed, returned -1 > Note: Using POSIX realtime > homemod: not loaded > <commandline>:0: exit value: 255 > <commandline>:0: rmmod failed, returned -1 > Note: Using POSIX realtime > tpmod: not loaded > <commandline>:0: exit value: 255 > <commandline>:0: rmmod failed, returned -1 > <commandline>:0: unloadrt failed > Note: Using POSIX realtime > > > > On Thu, Sep 1, 2022 at 10:42 PM Sam Sokolik <samco...@gmail.com> wrote: > >> Bary - Could we get all the files? >> custompanel.xml >> postgui_call_list.hal >> custom.hal >> >> I just built RIP on buster and ran the config (remarking out the missing >> files) >> I have an encoder in pin 10 and 11 and it seems to work with no crash. >> >> sam >> >> >> On Thu, Sep 1, 2022 at 9:45 PM Bari <bari00...@gmail.com> wrote: >> >>> Brand new setup using stepconf. if I spin the spindle encoder quickly >>> by hand I get: rtapi_app: caught signal 8 - dumping core >>> >>> Even if the machine is still in e-stop. Simple config using stepconf >>> LINUXCNC - 2.9.0~pre0 >>> >>> All default settings other than manual edit of LPT base address and >>> changed setp encoder.0.position-scale 4000.000000 Default is like >>> 100 vs 4000 >>> >>> Any ideas what causes this error? >>> >>> https://forum.linuxcnc.org/media/kunena/attachments/1324/simple.ini >>> >>> https://forum.linuxcnc.org/media/kunena/attachments/1324/simple.hal >>> >>> The only mention of a similar error: >>> forum.linuxcnc.org/24-hal-components/358...hercat-lcec?start=10 >>> >>> >>> >>> _______________________________________________ >>> Emc-users mailing list >>> Emc-users@lists.sourceforge.net >>> https://lists.sourceforge.net/lists/listinfo/emc-users >>> >> _______________________________________________ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users
