Dave Sherman <[EMAIL PROTECTED]> write:

>Could you post the output of 'ifconfig' and 'route -n'?

Bill Kenworthy <[EMAIL PROTECTED]> wrote:

> Have you installed/enabled a firewall?  Check
> /etc/Bastille/bastille-firewall.conf and the Drak firewall tools .  For
> me, running tinyfirewall (Drak tools)  set up masquerading through the
> box, but prevented any connection to the box at all.

civileme <[EMAIL PROTECTED]> wrote:
>What IRQ is it on?
>cat /etc/sysconfig/network*
>cat /etc/resolv.conf


Thanks for the rapid response !!!

No firewall on this unit. Being on a small home network
with a firewal/server being in place I went for the
"welcome to crackers" configuration  to try and KISS but
of course it fooled me !

ifconfig
eth0      Link encap:Ethernet  HWaddr 00:40:05:E3:39:94  
          inet addr:192.168.0.12  Bcast:192.168.0.255  Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:6 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:100 
          RX bytes:0 (0.0b)  TX bytes:780 (700.0 b)

lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:105 errors:0 dropped:0 overruns:0 frame:0
          TX packets:105 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:7700 (7.5 Kb)  TX bytes:7700 (7.5 Kb)



[root@home233]# route -n         (The non-working client machine)
Kernel IP routing table
Destination    Gateway        Genmask        Flags Metric Ref    UseIface
192.168.0.0    0.0.0.0        255.255.255.0   U     0      0        0 eth0
127.0.0.0      0.0.0.0         255.0.0.0      U     0      0        0 lo
0.0.0.0       192.168.0.10    0.0.0.0         UG    0      0        0 eth0


[root@home2]# route -n          (The working client machine)
Kernel IP routing table
Destination    Gateway        Genmask        Flags Metric Ref    UseIface
192.168.0.0    0.0.0.0        255.255.255.0   U     0      0        0 eth0
127.0.0.0      0.0.0.0         255.0.0.0      U     0      0        0 lo
0.0.0.0       192.168.0.10    0.0.0.0         UG    0      0        0 eth0

/etc/sysconfig/network
NETWORKING=yes
FORWARD_IPV4=false
HOSTNAME=home2.suslositna.org
DOMAINNAME=suslositna.org
GATEWAY=192.168.0.10
GATEWAYDEV=eth0
(this is exactly the same as the working client machine!)

/etc/resolv.conf
search mtaonline.net
nameserver 12.6.42.1 
nameserver 12.6.42.2
(exactly the same as working client machine)

Looks like maybe its time for ....!!!???

Thanks again to Everyone


> On Sat, 2001-12-01 at 05:12, William Bouterse wrote:
> > This could of course be strickly "bad timing"
> > However ;
> > generic ne 200 clone card has worked through LM6.x,7.x's-
> > 8.0freq now it doesn't..Worked before install of LM8.1....
> > 
> > card is recognized by install and even autoprobe works
> > without having to manually configure specs.
> >  (this is a "client" machine on small network)
> > 
> > ifconfig shows eth0 active with proper init address
> > The card can be "ping'd" internally and localhoast too .
> > Cannot ping outside machine. 
> > Can ping Bcast #
> > 
> > route shouws exact Ip routing as another working machine.....
> > 
> > I have used draknet as well as manually altering
> > the config files....
> > 
> > I have taken out this card and put it back in.
> > 
> > Before I actually replace it I was wondering if there was something
> > obvious I was missing here.?


-- 
William Bouterse
Talkeetna, Ak.

Want to buy your Pack or Services from MandrakeSoft? 
Go to http://www.mandrakestore.com

Reply via email to