Tim, That was the problem. A couple of the parameters did not get changed correctly. All is now right with the world, at least my world. Thanks.
John, N8WNA -----Original Message----- From: flexradio-boun...@flex-radio.biz [mailto:flexradio-boun...@flex-radio.biz] On Behalf Of Tim Ellison, W4TME Sent: Tuesday, March 06, 2012 4:20 PM To: flexradio@flex-radio.biz Subject: Re: [Flexradio] Problem with PSDR v2.3.5 Did you change the VAC cable parameters as suggested in the Release Notes? Tim Ellison, W4TME Product Management, Sales & Support FlexRadio Systems^(TM) 4616 W Howard Ln, Suite 1-150 Austin, TX 78728 Phone: 512-535-4713 Ext. 223 Email: t...@flexradio.com <mailto:t...@flexradio.com> Web: www.flexradio.com <http://www.flexradio.com> logo On 3/6/2012 4:08 PM, John Swink wrote: > Radio is a F5K+RX2+ATU+VU. I installed PSDR v2.3.5 yesterday and > seemed to be functioning properly until a few minutes ago. > > > > When I clicked on the 15m band button to move down the stack, I > received the following error: > > > > "AUDIO SUBSYSTEM ERROR: INVALID DEVICE > > Whoops! Looks like something has gone wrong in the Audio section. > > Go look in the Setup Form -> Audio Tab to verify the settings there. > > Since VAC is enabled, make sure you look at these settings as well." > > > > The panadapter froze up but audio was still heard. When I closed the > error message, the start button went dark and the audio stopped. When > I hit the start button again, the error message returned. > > > > With the start button dark, I hit the 12m band and hit start. The > radio came back on, but when I hit the 12m band button again, the > error message returned. I tried the 10& 20m bands with the same > results. Now these four bands will not function. The problem did not occur on 6m. > > > > These are my Audio Tab settings; > > > > Primary: > > Buffer-1024 > > Sample rate-192000 > > > > VAC 1: > > Driver-WDM-KS > > Input-Virtual cable 2 > > Output-Virtual cable 1 > > Buffer-1024 > > Sample rate-192000 > > Auto enable-checked > > PTT override-checked > > > > These are the same settings I used on v2.2.3 except Driver-MME and > Sample > rate-48000 > > > > VAC 2: > > Same settings as VAC 1 except Input-Virtual cable 4 > and Output-Virtual cable 3 > > > > Closing the software and rebooting does not correct the problem. > > A solution to the problem would be appreciated. > > > > John, N8WNA > > _______________________________________________ > FlexRadio Systems Mailing List > FlexRadio@flex-radio.biz > http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz > Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ > Knowledge Base: http://kc.flexradio.com/ Homepage: > http://www.flexradio.com/ _______________________________________________ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kc.flexradio.com/ Homepage: http://www.flexradio.com/ _______________________________________________ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge Base: http://kc.flexradio.com/ Homepage: http://www.flexradio.com/