Yep you must tell VAC to allow 192000 in the control panel for VAC before it
will.
Sent from my Verizon Wireless Droid
-----Original message-----
From: "Tim Ellison, W4TME" <t...@flex-radio.com>
To: flexradio@flex-radio.biz
Sent: Tue, Mar 6, 2012 21:19:50 GMT+00:00
Subject: Re: [Flexradio] Problem with PSDR v2.3.5
Did you change the VAC cable parameters as suggested in the Release Notes?
Tim Ellison, W4TME
Product Management, Sales & Support
FlexRadio Systems^(TM)
4616 W Howard Ln, Suite 1-150
Austin, TX 78728
Phone: 512-535-4713 Ext. 223
Email: t...@flexradio.com <mailto:t...@flexradio.com>
Web: www.flexradio.com <http://www.flexradio.com>
logo
On 3/6/2012 4:08 PM, John Swink wrote:
Radio is a F5K+RX2+ATU+VU. I installed PSDR v2.3.5 yesterday and seemed
to
be functioning properly until a few minutes ago.
When I clicked on the 15m band button to move down the stack, I received
the
following error:
"AUDIO SUBSYSTEM ERROR: INVALID DEVICE
Whoops! Looks like something has gone wrong in the Audio section.
Go look in the Setup Form -> Audio Tab to verify the settings there.
Since VAC is enabled, make sure you look at these settings as well."
The panadapter froze up but audio was still heard. When I closed the
error
message, the start button went dark and the audio stopped. When I hit the
start button again, the error message returned.
With the start button dark, I hit the 12m band and hit start. The radio
came back on, but when I hit the 12m band button again, the error message
returned. I tried the 10& 20m bands with the same results. Now these
four
bands will not function. The problem did not occur on 6m.
These are my Audio Tab settings;
Primary:
Buffer-1024
Sample rate-192000
VAC 1:
Driver-WDM-KS
Input-Virtual cable 2
Output-Virtual cable 1
Buffer-1024
Sample rate-192000
Auto enable-checked
PTT override-checked
These are the same settings I used on v2.2.3 except Driver-MME and Sample
rate-48000
VAC 2:
Same settings as VAC 1 except Input-Virtual cable 4 and
Output-Virtual cable 3
Closing the software and rebooting does not correct the problem.
A solution to the problem would be appreciated.
John, N8WNA
_______________________________________________
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/ Homepage:
http://www.flexradio.com/
_______________________________________________
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/ Homepage:
http://www.flexradio.com/
_______________________________________________
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/ Homepage: http://www.flexradio.com/