Ooops, incomplete thought - so regarding changing your virtual machine console, assume your virtual machine console is presently at 009 (the default, issue CP Q V CONS to find out), change it to 0320: CP DEFINE 009 0320 Ask your DR provider to make the change permanently in the CP directory, so you don't have to remember to change it. -MC From: The IBM z/VM Operating System [mailto:IBMVM@LISTSERV.UARK.EDU] On Behalf Of Michael Coffin Sent: Monday, June 20, 2011 9:48 AM To: IBMVM@LISTSERV.UARK.EDU Subject: Re: Problems at DR test I think it's just LOADPARM ccuu, so if your consoles is at virtual address 0001: CP IPL xxxx LOADPARM 0001 Of course, you can avoid this all together by making your virtual machine console address the same as your Operator Console address (as specified in your SYSTEM CONFIG). So let's say you have a 3270 console at address 0320 at your production site, and it is listed in your SYSTEM CONFIG under OPERATOR_CONSOLES, when you IPL your RES pack it will find 0320 and write its messages there without manually specifying the console address on the IPL command. -Mike From: The IBM z/VM Operating System [mailto:IBMVM@LISTSERV.UARK.EDU] On Behalf Of Frank M. Ramaekers Sent: Monday, June 20, 2011 9:41 AM To: IBMVM@LISTSERV.UARK.EDU Subject: Re: Problems at DR test I'm getting 'HCPCLT1013E An invalid operand was supplied for LOADPARM - CONS-0001.
Frank M. Ramaekers Jr. _____ From: The IBM z/VM Operating System [mailto:IBMVM@LISTSERV.UARK.EDU] On Behalf Of Kris Buelens Sent: Monday, June 20, 2011 8:12 AM To: IBMVM@LISTSERV.UARK.EDU Subject: Re: Problems at DR test You z/VM system didn't find a 3270 console, so it is using the "System console" As you run second level, you an respond to VM questions using #CP VINPUT VMSG xxxx To make it easier: before you IPL, issue CP Q V CONS note the address, often 009 CP TERM CONMODE 3270 CP IPL xxxx LOADPARM CONS=yyyy (xxxx is the disk your VM resident is on; yyyy is the address you found in Q V CONS) 2011/6/20 Frank M. Ramaekers <framaek...@ailife.com> I'm attempting to bring up our VM system under 2nd level at the DR site. The problem that I'm running into is: 08:58:10 HCPZCO6718I Using parm disk 1 on volume 610RES (device 06F8) 08:58:10 HCPZCO6718I Parm disk resides on cylinders 39 through 158. 08:58:10 Start ((Warm|Force|COLD|CLEAN) (DRain) (DIsable) (NODIRect) 08:58:10 (NOAUTOlog)) or (SHUTDOWN) H HCPSED6013A A CP read is pending. The HCPSED6013A seems to be the problem. At our site, I have two VMs that I can IPL under our z/VM 5.4. One will IPL just fine (i.e. no HCPSED6013A) the other doesn't' and displays this message. Both VMs are configured (DIRECT) the same. I'm at a loss as to why this happens with one and not the other. We had no problems during the last DR, but we've applied z/VM 5.4 maintenance since then (1003). Ideas? Frank M. Ramaekers Jr. Systems Programmer MCP, MCP+I, MCSE & RHCE American Income Life Insurance Co. Phone: (254)761-6649 1200 Wooded Acres Dr. Fax: (254)741-5777 Waco, Texas 76701 _____________________________________________________ This message contains information which is privileged and confidential and is solely for the use of the intended recipient. If you are not the intended recipient, be aware that any review, disclosure, copying, distribution, or use of the contents of this message is strictly prohibited. If you have received this in error, please destroy it immediately and notify us at privacy...@ailife.com. -- Kris Buelens, IBM Belgium, VM customer support _____________________________________________________ This message contains information which is privileged and confidential and is solely for the use of the intended recipient. If you are not the intended recipient, be aware that any review, disclosure, copying, distribution, or use of the contents of this message is strictly prohibited. If you have received this in error, please destroy it immediately and notify us at privacy...@ailife.com.
