Well I knew my generic answer was not going to be enough. I'm not aware of a wiring diagram for the legacy drive system. It was all pre-wired and the manuals only showed where to and how to mount the components to the machine.
Since you are familiar with electronic, I'm not sure where you need help. I can't give you a wiring diagram for components that I don't know that you are using. Tim Sent from BlueMail On Jul 20, 2017, 4:46 AM, at 4:46 AM, Richard Ellis <rchrd.ell...@gmail.com> wrote: >Roger >I asked for a wiring diagram, No good looking at the wires -------I >HAVE >NONE-------- regards safety, I have an always do take note !! However I >do >not think a wiring diagram as used by legacy is going to kill me. I >have >been involved with electrics for many years, *A wiring diagram is what >I am >after* > >Richard > >On Thursday, July 20, 2017 at 9:23:37 AM UTC+1, ITwoodwork wrote: >> >> Hi Guys >> >> Given Tim's information any competent electrician should be able to >> investigate the wiring and draw a circuit diagram or schematic. >Otherwise >> leave the electrics alone, electricity can curl your hair if you get >a >> shock, it can burn and even kill you. Treat with respect, probably >more >> than you might give the wife or partner. >> >> Roger & out. >> >> >> PS I have had live demonstrations of electric shocks! >> >> >> Sent from TouchMail for Windows 10 <http://bit.ly/1PH8eIw> >> >> >> >> >> *From:* Bill Bulkeley >> *Received:* 20/07/2017 09:13:12 +01:00 >> *To:* legacy-orna...@googlegroups.com <javascript:> >> >> I don’t think i have ever seen a wiring diagram for the drive motor, >> controller and limit switches >> >> Be nice to have it hope someone does and posts it >> >> >> >> Bill >> >> >> >> >> >> *From:* legacy-orna...@googlegroups.com <javascript:> [mailto: >> legacy-ornamental-mills@googlegroups.com <javascript:>] *On Behalf Of >*Richard >> Ellis >> *Sent:* Thursday, 20 July 2017 5:24 PM >> *To:* Legacy Ornamental Mills >> *Subject:* Wiring diagram >> >> >> >> Hi All >> >> I have now got a motor for my Revo, Leadscrew---- but am a bit stuck >for a >> wiring diagram, I assume they are the same for other Legacy non CNC >models. >> >> If any one has one that shows the control box and limit switches etc. >Can >> you post it on here or email me >> >> Thanks >> >> Richard >> >> -- >> You received this message because you are subscribed to the Google >Groups >> "Legacy Ornamental Mills" group. >> To unsubscribe from this group and stop receiving emails from it, >send an >> email to legacy-ornamental-mills+unsubscr...@googlegroups.com >> <javascript:>. >> To post to this group, send email to legacy-orna...@googlegroups.com >> <javascript:>. >> Visit this group at >> https://groups.google.com/group/legacy-ornamental-mills. >> For more options, visit https://groups.google.com/d/optout. >> >> >> >> >> ><http://www.avg.com/email-signature?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=emailclient> >> >> Virus-free. www.avg.com >> ><http://www.avg.com/email-signature?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=emailclient> > >> >> >> >> -- >> You received this message because you are subscribed to the Google >Groups >> "Legacy Ornamental Mills" group. >> To unsubscribe from this group and stop receiving emails from it, >send an >> email to legacy-ornamental-mills+unsubscr...@googlegroups.com >> <javascript:>. >> To post to this group, send email to legacy-orna...@googlegroups.com >> <javascript:>. >> Visit this group at >> https://groups.google.com/group/legacy-ornamental-mills. >> For more options, visit https://groups.google.com/d/optout. >> > >-- >You received this message because you are subscribed to the Google >Groups "Legacy Ornamental Mills" group. >To unsubscribe from this group and stop receiving emails from it, send >an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. >To post to this group, send email to >legacy-ornamental-mills@googlegroups.com. >Visit this group at >https://groups.google.com/group/legacy-ornamental-mills. >For more options, visit https://groups.google.com/d/optout. -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout.
