Tim Thanks for the answer, If there has been no wiring diagram for the Legacy, that is all I needed to know. I was a little surprised that no one asked what power voltage I was thinking of using, could have been 12 or 24 volt dc as i;e Windscreen wiper motors,.I don't think that would kill me ! ! !?? I did smile to myself re the safety lessons, all good knowledge and I do not get offended, so thanks to the others who responded. NOW ! Yesterday I started changing the Drive unit from the old Woodchuck to the Revo. It is 110 volt of course and runs through the transformer 240 volt The end of the leadscrew had been just cut off and the collar complete with grub screw fastened,---------- not good engineering in my book,-----hit and miss as to where the grub screw grips?? More about it later Richard
On Thursday, July 20, 2017 at 11:29:19 PM UTC+1, Tim wrote: > > Well I knew my generic answer was not going to be enough. I'm not aware > of a wiring diagram for the legacy drive system. It was all pre-wired and > the manuals only showed where to and how to mount the components to the > machine. > > Since you are familiar with electronic, I'm not sure where you need help. > I can't give you a wiring diagram for components that I don't know that you > are using. > > Tim > > > Sent from BlueMail <http://www.bluemail.me/r?b=10066> > On Jul 20, 2017, at 4:46 AM, Richard Ellis <rchrd....@gmail.com > <javascript:>> wrote: >> >> Roger >> I asked for a wiring diagram, No good looking at the wires -------I HAVE >> NONE-------- regards safety, I have an always do take note !! However I do >> not think a wiring diagram as used by legacy is going to kill me. I have >> been involved with electrics for many years, *A wiring diagram is what I >> am after* >> >> Richard >> >> On Thursday, July 20, 2017 at 9:23:37 AM UTC+1, ITwoodwork wrote: >>> >>> Hi Guys >>> >>> Given Tim's information any competent electrician should be able to >>> investigate the wiring and draw a circuit diagram or schematic. Otherwise >>> leave the electrics alone, electricity can curl your hair if you get a >>> shock, it can burn and even kill you. Treat with respect, probably more >>> than you might give the wife or partner. >>> >>> Roger & out. >>> >>> >>> PS I have had live demonstrations of electric shocks! >>> >>> >>> Sent from TouchMail for Windows 10 <http://bit.ly/1PH8eIw> >>> >>> >>> >>> >>> *From:* Bill Bulkeley >>> *Received:* 20/07/2017 09:13:12 +01:00 >>> *To:* legacy-orna...@googlegroups.com >>> >>> I don’t think i have ever seen a wiring diagram for the drive motor, >>> controller and limit switches >>> >>> Be nice to have it hope someone does and posts it >>> >>> >>> >>> Bill >>> >>> >>> >>> >>> >>> *From:* legacy-orna...@googlegroups.com [mailto: >>> legacy-ornamental-mills@googlegroups.com] *On Behalf Of *Richard Ellis >>> *Sent:* Thursday, 20 July 2017 5:24 PM >>> *To:* Legacy Ornamental Mills >>> *Subject:* Wiring diagram >>> >>> >>> >>> Hi All >>> >>> I have now got a motor for my Revo, Leadscrew---- but am a bit stuck for >>> a wiring diagram, I assume they are the same for other Legacy non CNC >>> models. >>> >>> If any one has one that shows the control box and limit switches etc. >>> Can you post it on here or email me >>> >>> Thanks >>> >>> Richard >>> >>> -- >>> You received this message because you are subscribed to the Google >>> Groups "Legacy Ornamental Mills" group. >>> To unsubscribe from this group and stop receiving emails from it, send >>> an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. >>> To post to this group, send email to legacy-orna...@googlegroups.com. >>> Visit this group at >>> https://groups.google.com/group/legacy-ornamental-mills. >>> For more options, visit https://groups.google.com/d/optout. >>> >>> >>> >>> >>> <http://www.avg.com/email-signature?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=emailclient> >>> >>> Virus-free. www.avg.com >>> <http://www.avg.com/email-signature?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=emailclient> >>> >>> >>> >>> >>> -- >>> You received this message because you are subscribed to the Google >>> Groups "Legacy Ornamental Mills" group. >>> To unsubscribe from this group and stop receiving emails from it, send >>> an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. >>> To post to this group, send email to legacy-orna...@googlegroups.com. >>> Visit this group at >>> https://groups.google.com/group/legacy-ornamental-mills. >>> For more options, visit https://groups.google.com/d/optout. >>> >> -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. Visit this group at https://groups.google.com/group/legacy-ornamental-mills. For more options, visit https://groups.google.com/d/optout.
