Keep on working with it Richard, you are doing a good job! The wave attachment, is something that is uniquely OURS, that is the LOM group's, No one else can easily make the same type of designs, Ive had wood turners ask me how I made that? even Guys with OT machines can not do a wave, THAT is Cool (in my book/ a feather in my cap, so to speak !) ;-) Have a GREAT DAY. C.A.G. On Friday, August 23, 2019, 04:53:09 AM EDT, Richard Ellis <rchrd.ell...@gmail.com> wrote: Hi CurtI am nearly sure how I did it,, but will make sure later today. It certainly wasn't just by moving one hole on/in the 40 hole alloy plate.Richard
On Thursday, August 22, 2019 at 1:25:22 PM UTC+1, Curt George wrote: RichardI like it, I hope you are able to repeat the process again? that is a neat cut! C.A.G. On Thursday, August 22, 2019, 07:15:38 AM EDT, Richard Ellis <rchrd...@gmail.com> wrote: Well Tim you are rightWhat I did was to keep my finger in place on the pin of the TK ( pressing gently in one direction )The cut was done, by putting the pin in the next hole to where it should have been.. I:E I made it make a mistake like I did. All trial and error on my part. The question is ---shall I be able to do it again ??Richard On Thursday, August 22, 2019 at 11:44:06 AM UTC+1, Tim wrote: That's something I have not seen. You might want to add a light return spring to prevent any loss of time issues in the extended sine wave. Sent from Samsung tablet -------- Original message --------From: Richard Ellis <rchrd...@gmail.com> Date: 8/22/19 3:16 AM (GMT-08:00) To: Legacy Ornamental Mills <legacy-orna...@ googlegroups.com> Subject: Re: TK Reciprocater long curves Tim & othersHere are a couple of pics of the same bit of wood.Richard On Thursday, August 22, 2019 at 8:33:28 AM UTC+1, Richard Ellis wrote: Thanks for the info Curt & Bill I have printed it of to study and then it will go into my folder for other s who end up with my RevoRichard On Sunday, August 18, 2019 at 10:46:40 AM UTC+1, Richard Ellis wrote: Hi all you LOM expertsI am trying to do a long (approx ) 6 inch flute with the TK at present with the standard index gear I get a 2 inch point to point curve If I change to the 2X gear I think it will only give me a four inch point to point --- I have not tried but it's my guess !!Am I trying to do the impossible???Richard -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+ unsubscr...@googlegroups.com. To view this discussion on the web visit https://groups.google.com/d/ msgid/legacy-ornamental-mills/ 58a54418-8c91-4041-841b- 92cf15c106f1%40googlegroups. com. -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+ unsubscr...@googlegroups.com. To view this discussion on the web visit https://groups.google.com/d/ msgid/legacy-ornamental-mills/ 0a70efeb-04b4-4766-b093- 91238c058645%40googlegroups. com. -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/3aaab4ba-42b5-4616-bfb3-51369e2a304c%40googlegroups.com. -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com. To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/2126396986.853782.1566564821968%40mail.yahoo.com.