Rich, Yes I do have a layer 2 switch defined.
George Shedlock Jr AEGON Information Technology AEGON USA 502-560-3541 -----Original Message----- From: Linux on 390 Port [mailto:[EMAIL PROTECTED] On Behalf Of Rich Smrcina Sent: Tuesday, November 25, 2008 8:59 AM To: LINUX-390@VM.MARIST.EDU Subject: Re: SLES 10 SP 2 - Starter Vswitch Do you actually have a Layer 2 VSwitch defined? If not, then answer 2 to the last question. Shedlock, George wrote: > Gentle Listers, > > I have the SLES 10 SP2 starter system build and am attempting to create my > first guest from the starter system. I start the install process, console log > follows: > > Activating manual setup program. > >>>> Linuxrc v2.0.79 (Kernel 2.6.16.60-0.21-default) <<< > > Main Menu > > 1) Settings > 2) System Information > 3) Kernel Modules (Hardware Drivers) > 4) Start Installation or System > 5) Verify Installation CD-ROM/DVD > 6) Eject CD > 7) Exit or Reboot > 8) Power off > > 4 > Start Installation or System > > 1) Start Installation or Update > 2) Boot Installed System > 3) Start Rescue System > > 1 > > Choose the source medium. > > 1) CD-ROM > 2) Network > 3) Hard Disk > > 2 > > Choose the network protocol. > 1) FTP > 2) HTTP > 3) NFS > 4) SMB / CIFS (Windows Share) > 5) TFTP > > 1 > > Please select the type of your network device. > > 1) OSA-2 or OSA Express > 2) Hipersockets > -------------------- > 3) Channel To Channel (CTC) > 4) ESCON > 5) Inter-User Communication Vehicle (IUCV) > 1 > > Please choose the CCW bus interface. > > 1) QDIO > 2) LCS > > 1 > > Please choose the physical medium. > > 1) Ethernet > 2) Token Ring > > 1 > qdio: loading QDIO base support version 2 > qeth: loading qeth S/390 OSA-Express driver > > 0.0.0340 1731/01 > 0.0.0341 1731/01 > 0.0.0342 1731/01 > > > Device address for read channel> > 0.0.0340 > > Device address for write channel> > 0.0.0341 > > Device address for data channel> > 0.0.0342 > > Portname to use> > > > Enable OSI Layer 2 support? > > 1) Yes > 2) No > > 1 > > MAC address> > 101095 > qeth: Device 0.0.0340/0.0.0341/0.0.0342 is a Guest LAN QDIO card > (level: V532) with link type GuestLAN QDIO (portname: ) > qeth: MAC address 02:ad:c3:10:10:95 successfully registered on device > eth0 > > So far so good. Then I get prompted with: > > Please select the type of your network device. > > 1) OSA-2 or OSA Express > 2) Hipersockets > -------------------- > 3) Channel To Channel (CTC) > 4) ESCON > 5) Inter-User Communication Vehicle (IUCV) > > > Any suggestions? > > George Shedlock Jr > AEGON Information Technology > AEGON USA > 502-560-3541 > > ---------------------------------------------------------------------- > For LINUX-390 subscribe / signoff / archive access instructions, send > email to [EMAIL PROTECTED] with the message: INFO LINUX-390 or > visit http://www.marist.edu/htbin/wlvindex?LINUX-390 > -- Rich Smrcina VM Assist, Inc. Phone: 414-491-6001 Ans Service: 360-715-2467 http://www.linkedin.com/in/richsmrcina Catch the WAVV! http://www.wavv.org WAVV 2009 - Orlando, FL - May 15-19, 2009 ---------------------------------------------------------------------- For LINUX-390 subscribe / signoff / archive access instructions, send email to [EMAIL PROTECTED] with the message: INFO LINUX-390 or visit http://www.marist.edu/htbin/wlvindex?LINUX-390 ---------------------------------------------------------------------- For LINUX-390 subscribe / signoff / archive access instructions, send email to [EMAIL PROTECTED] with the message: INFO LINUX-390 or visit http://www.marist.edu/htbin/wlvindex?LINUX-390