I didn't know Stewart was doing them, I'm guessing but I'd say they weren't engineered either. IMHO the threaded bar type are a pain in the Ar@@ . I have them myself and they are quite difficult to adjust. Every time you want to make a change, or even to get them set in the first place, the whole lower control arm has to be taken off the bottom of the strut. Just imagine the local grease monkey at Bob Jane T Mart stuffing around trying to do a wheel alignment.
The shim type just have to be loosened and the shim pushed in place, re-tightened and it's done! my .02$ worth :)) Cam CM510 www.sprite.com.au/cm510 ----- Original Message ----- From: Chris Howard <[EMAIL PROTECTED]> To: <[EMAIL PROTECTED]> Sent: Friday, February 22, 2002 4:36 PM Subject: RE: Whiteline suspension upgrade > Stewart Wilkins does them with a threaded bar instead of shims... Quite > nice, $220 a pair exchange, includes new bushes. > > Mad Dat also has a similar one, although IMHO Stewart's look better and > I think are cheaper. > > Cheers, > > Chris > > > -----Original Message----- > > From: [EMAIL PROTECTED] > > [mailto:[EMAIL PROTECTED]] On Behalf Of CM510 > > Sent: Friday, 22 February 2002 2:41 PM > > To: [EMAIL PROTECTED] > > Subject: Re: Whiteline suspension upgrade > > > > > > No issues known to me Terry, > > > > Cause they modify your control arms (cut and tig welded using > > 6mm plate and > > bolted with M8 High tensile bolts), any variance in length is already > > accounted for. Basically when they are cut and modified with > > no spacers you > > are left with an original length control arm. Shims (that > > are supplied) are > > then added to get the desired adjustment. > > > > The Whiteline 'engineer approved' mods retail at $280+gst or > > if you get em > > through me $269 with gst included, with the shims for up to > > 3.5 deg neg > > camber. > > > > I can also get them done by a guy here in Melbourne for $199 > > with shims etc, > > to exactly the same standards but without the official > > engineers approval > > for $199. > > > > > > Cam > > CM510 > > www.sprite.com.au/cm510 > > ----- Original Message ----- > > From: Terry Rudd <[EMAIL PROTECTED]> > > To: <[EMAIL PROTECTED]> > > Sent: Friday, February 22, 2002 2:46 PM > > Subject: RE: Whiteline suspension upgrade > > > > > > > Cam, > > > > > > These sound like worth a look. > > > > > > Any known issues? eg do they fit all of the xmembers out there? > > > Cost? > > > Anything else you can tell us. > > > > > > regards > > > TR > > > > > > -----Original Message----- > > > From: [EMAIL PROTECTED] > > > [mailto:[EMAIL PROTECTED]]On Behalf Of cm510 > > > Sent: Friday, 22 February 2002 2:36 PM > > > To: [EMAIL PROTECTED] > > > Subject: Re: Whiteline suspension upgrade > > > > > > > > > Guys, the adjustable rubber mounted lower control arms I get through > > > Whiteline are meant to be engineer aproved for road use. > > They give up to > > > 3.5 deg neg camber with a nice little increase in track > > width as well. > > > > > > Cam > > > CM510 > > > www.sprite.com.au/cm510 > > > > > > > > > > > > --membersozdat------------------------------------------------------- OZDAT Mailing List Please Note:- Send (un)subscribe requests to [EMAIL PROTECTED] Send submissions to [EMAIL PROTECTED] No unauthorised redistribution of this email http://www.ozdat.com/ozdatonline/index.htm http://www.ozdat.com/ozdatonline/listindex.html http://www.mail-archive.com/[email protected]/ ---------------------------------------------------------------------
