I can address the ball joints. Jack the front end to unload the wheel and try to wiggle the tire from the top and bottom. If it moves at the bottom ball joint, replace the ball joint. Also, if the ball joint boot is torn, replace the ball joint.
To replace the ball joint the steering knuckle must be removed completely, which involves removing the brake caliper and the hub/brake disk/dust shield assembly first. There are two special tools that let you disconnect the upper ball joint (first) and then the lower ball joint (second) to remove the knuckle/spindle. The ball joint can be pounded out of the spindle with a big hammer but another special tool (there are two types) is needed to press in the new ball joint without damaging the boot. I haven't done the inboard bushing where camber gets adjusted. The eccentric kit you show is just the bolt, which may be OK. The main thing to replace is the rubber bushing assembly which requires removal of the lower control arm. And that requires a GOOD spring compressor. This is a big job The shocks are not difficult to replace and don't require special tools other than 12 point sockets the correct size. As I recall, that filter goes inside the fluid reservoir, which is inside the engine compartment. Concerning this suspension/steering work. It's probably investigating first to see what really needs to be replaced. Inspecting for torn ball joint boots is trivial. Ball joint shake is easy. Inspecting the bushing at the eccentric takes some experience. Scott _____ From: Mercedes [mailto:mercedes-boun...@okiebenz.com] On Behalf Of r...@rhonald.me Sent: Saturday, December 21, 2013 6:56 PM To: Mercedes Discussion List Subject: Re: [MBZ] 123 '85 TD Wagon castor Adjustors and other suspensionstuff OK, I am getting new Bilstein shocks in front, Sachs-Boge self leveling shocks and Febi accumulators in the rear. The car is still perfectly level even when loaded. 1. While the car is up, the shop says the castor adjustors have wear (small). Does it make sense to do this now? From what I have seen, it relates to the front end alignment. I am getting confused looking at parts. Is this what I need x 2? 1163300018 <http://www.autohausaz.com/secure/PartImages/1163300018.jpg> Genuine Mercedes <http://www.autohausaz.com/html/brandnames.html> Alignment Caster/Camber Kit; Front Lower Inner; Eccentric Bolt Kit 2 kits per car. 2. Deciding whether to have the ball joints done at the same time though there is no inspection reports of wear noted and the car does not present any tracking issues. Is it possible to check anything when it is not on the lift? Two boots and two boot kits, correct? Just wanting to get everything tight again. The black sedan is all done and it made a world of difference, but...just in time for two huge tree branches to smash the top in the middle. Sighhhh! 3. Where is the hydraulic suspension filter located for the self leveling suspension in the rear? 0021845501 <http://www.autohausaz.com/secure/PartImages/0021845501.jpg> Genuine Mercedes <http://www.autohausaz.com/html/brandnames.html> Hydraulic Suspension Oil Filter For models with self-leveling rear suspension. 4. I have to wait on the Rear Control Arms. Told they have some play. Not sure how to feel this when driving. Thanks R -------- Original Message -------- Subject: Re: [MBZ] 123 '85 TD Wagon oil cooler lines From: Gary Hurst <jabbahur...@gmail.com> Date: Sat, December 21, 2013 12:38 pm To: Mercedes Discussion List <mercedes@okiebenz.com> also, that's just hte upper hose. the lower hose might just be available only in tructec or genuine mercedes, so you might have to get the lower one in genuine or just live with the tructec. seems i too have a special agreement with monark to sell you those hoses, but i'd probably get a genuine one if i were you if the tructec actually turns out chinese On Sat, Dec 21, 2013 at 11:24 AM, <r...@rhonald.me> wrote: > Morning All, I am ready to replace the oil cooler hoses on the wagon. I > was price shopping, and came across these. > > > https://mercedessource.com/store/116-123-617-turbo-diesel-upper-oil-cooler-h ose-instructions > > Has anyone had experience with these? The German company? > > Looking for recommendations. > > Thanks > > R > 85 300TD Wagon 230,000 miles > > > > > > _______________________________________ > http://www.okiebenz.com > > To search list archives http://www.okiebenz.com/archive/ > > To Unsubscribe or change delivery options go to: > http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com > > -- *reliable vendor of superior parts for mercedes and other european cars* *www.BuyEUROparts.com <http://www.BuyEUROparts.com>* _______________________________________ http://www.okiebenz.com To search list archives http://www.okiebenz.com/archive/ To Unsubscribe or change delivery options go to: http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com _______________________________________ http://www.okiebenz.com To search list archives http://www.okiebenz.com/archive/ To Unsubscribe or change delivery options go to: http://mail.okiebenz.com/mailman/listinfo/mercedes_okiebenz.com
