I also got the Intel 810E motherboard with a 550E cpu, ASUS CUW-RM
I can install the VGA drive.
I just download the driver and follow the document in Intel web page.
http://support.intel.com/support/graphics/intel810/linuxsoftware.htm
However this drive does not include the Audio driver for 810E AC97 audio!!!
Anyone know how to config it?
Terence
Gina wrote:
> Hi Tom,
>
> Its me again with the same problem but now in Air.
> Ive tried installing the same files I got it working with in MAndrake 6.5
> and it doesnt work in 7. After hunting around I found some info with later
> files to try out. I cant get them working.
>
> I am confused with what files Ive got and what ones should be used and even
> then, the commands to use to install the XFCom.
>
> what stages need to be done? like:
> install the XFCom file
> build the kernel
> then install the kernel
>
> The files I now have are:
>
> XFCom-i810-glibc2.1.0.0-rh60.rpm
> XFCom-i810-glibc2.1.0.0-rh61.rpm
> How do I "install" is it "rpm -i" or "rpm -Uvh"???
>
> When I go into Kpackage it says it is installed. Well they both are now and
> I cant uninstall one or the other as I get an error message saying it
> contains mulitple files.
>
> Then the other files Ive got:
>
> I810Gtt-0.1-rh60.i386.rpm
> I810Gtt-0.1-rh61.i386.rpm
>
> and
>
> I810Gtt-0.1-4.src.rpm
> I810Gtt-0.1-5.src.rpm
>
> I dont know which one of these to use. My guess was that I can install with
> the I810Gtt-0.1-rh* or build and compile using the I810Gtt-0.1-4 or 5*.
> Either one should work? They dont.
> when I run the I810Gtt-0.1-rh* ones sure, they show up in the kpackage as
> installed but no references or files seem to go anywhere. I now also have
> both of them (60+61 in the kpackage aswell)
>
> When I try either of the bottom files I get a horrible error script message
> that Ive pasted below.
>
> when I search for XFCom, its no where to be found.
>
> Antoher issue I think may be contributing is the XF86_SVGA server. It wasnt
> installed during installation even when I chose recommended install. I
> think I got it installed ok eventually, it shows in the same dir as the
> VGA16 now. I guess I still get confused with the links. there are 4
> different link options to run and I dont know which of these I need. They
> are:
>
> cd/ etc/X11
> ln -sf /usr/X11R6/bin/XFCom_i810 X
> ln -sf /usr/X11R6/bin/XFCom_i810 /etc/X11/X
> ln -sf /usr/X11R6/bin/XFCom_i810 /usr/X11R6/bin/X
>
> which ones do I do?
> and where does the SVGA server get used, the only reference to that is
> during xf86config choosing the SVGA not SGA16. Im not sure if any of the
> above link settings need to refer to the SVGA as when I looked into one of
> the links it was refering to VGA16.
>
> Version 7 I got as it said it "supports i810. "BUT" it is not an option as
> you still need the kernel or something similar to that. Also in the earlier
> i810 setup support with md6.5 that I got working thanks to your help, it
> says "After you have successfully installed the vga16 server (which I
> have[even though Im getting only 1 horrible resolution]) you can upgrade
> your install with the XFCom X Server which will support high resolutions
> then further into the complete install of xfree it says "You can find the
> correctly compiled XF86_SVGA server with i810 support..."
>
> I am so confused. I sure would appreciate any help
>
> regards
> Gina
>
> ----- Original Message -----
> From: "Thomas J. Kwasnik" <[EMAIL PROTECTED]>
> To: "Gina" <[EMAIL PROTECTED]>
> Sent: Tuesday, 18 January 2000 08:43: pm
> Subject: Re: [newbie] X configure help PLEASE
>
> > My pleasure, and yes i would like to know your progress
> >
> > Gina wrote:
> > >
> > > Thank you so much Tom!
> > > you know what I'll be doing tonight :)
> > > I'll let you know how I go with it.
> > >
> > > regards
> > > Gina
> > >
> > > ----- Original Message -----
> > > From: "Tom Kwasnik" <[EMAIL PROTECTED]>
> > > To: "Gina" <[EMAIL PROTECTED]>
> > > Sent: Tuesday, 18 January 2000 05:07: pm
> > > Subject: Re: [newbie] X configure help PLEASE
> > >
> > > > On Mon, 17 Jan 2000, you wrote:
> > > >
> > > > Sure, in fact, i'll do one better than that, in my reply here, i'll
> give
> > > you
> > > > the release notes that *I* found on the i810 video chipset....I also
> have
> > > > mandrake 6.5, and have had my ups and downs in the hardware area as
> far
> > > as
> > > > setup, so if i can be at all helpful, by all means let me
> know.....here is
> > > the
> > > > release :
> > > >
> > > > (please bear in mind that all this may NOT necessarily be applicable
> to
> > > > you....i doubt you'll need kernel re-configuration)
> > > >
> > > > This document is provided by Intel as a service for its customers
> only.
> > > THIS DOCUMENT IS PROVIDED "AS IS" WITH NO WARRANTIES WHATSOEVER,
> INCLUDING
> > > ANY
> > > > WARRANTY OF MERCHANTABILITY, NON-INFRINGEMENT FITNESS FOR ANY
> PARTICULAR
> > > PURPOSE, OR ANY WARRANTY OTHERWISE ARISING OUT OF ANY
> > > > PROPOSAL, SPECIFICATION OR SAMPLE. Intel disclaims all liability,
> > > including liability for infringement of any proprietary rights, relating
> to
> > > use of information in this document. No license,
> > > > express or implied, by estoppel or otherwise, to any intellectual
> property
> > > rights are granted herein.
> > > >
> > > > This document details how to get Linux* up and running on either an
> Intel®
> > > 810 or an Intel® 810E chipset-based motherboard. This document was
> written
> > > using RedHat* 6.0 as a reference
> > > > platform; some details may not be valid on other distributions or
> > > versions.
> > > >
> > > > Table of Contents
> > > >
> > > > Requirements
> > > > Features
> > > > Installing a new system
> > > > Kernel Setup
> > > > X Server Installation
> > > > Compiling X from source
> > > > References
> > > > Known Issues
> > > > Revision History
> > > >
> > > > Requirements:
> > > >
> > > > XFree86 3.3.5
> > > > Kernel version 2.2.X
> > > > glibc 2.1
> > > > gcc
> > > >
> > > >
> > > >
> > > > Features:
> > > >
> > > > XFree86 3.3.5 compatible
> > > > Support for up to 1600x1200 resolutions
> > > > Hardware cursor support
> > > > Acceleration for 8,16 and 24 bit depths
> > > >
> > > >
> > > >
> > > > Installing a new system:
> > > > If you are installing a Linux* distribution on a new system there are
> a
> > > few things you should know to help with the install. Distributions that
> are
> > > using XFree86 3.3.5 or earlier do not have built-in
> > > > support for the Intel® 810 Chipset family. You will have to install
> the
> > > 'vga16' X server, then after your system has been loaded you need to get
> and
> > > install the accelerated X server. Also, there
> > > > may be an issue with the distribution not recognizing all of the
> memory in
> > > your system. This should not cause a problem with the installation and
> can
> > > be fixed after the install is done as is detailed
> > > > below. When doing your install, be sure that you include the gcc
> compiler.
> > > It is needed to compile the agpgart module. All other aspects of the
> install
> > > should proceed as expected.
> > > >
> > > >
> > > > Kernel setup:
> > > >
> > > > 1.Check your Memory. Linux* kernel 2.2.X has a problem recognizing
> all
> > > the memory on some Intel® 810 and Intel® 810E chipset-based systems.
> This
> > > will make the system seem very
> > > > slow, or just not as fast as it could be. To check your system,
> run
> > > this command at a command prompt.
> > > >
> > > > cat /proc/meminfo
> > > >
> > > >
> > > > Look for a line that says:
> > > >
> > > > MemTotal: XXXXX kb
> > > >
> > > >
> > > > If this number is not close to the amount of RAM in your system,
> you
> > > will have to tell the kernel how much RAM you have. Note that this
> should be
> > > about 1-2 MB less than your actual
> > > > system memory. This is because the graphics chip uses system RAM
> for
> > > its 1MB frame-buffer.
> > > >
> > > > 2.Specify an amount of RAM. For the kernel to know how much RAM you
> > > have available for use you will need to supply a boot parameter to LILO,
> > > either at the boot prompt or in the
> > > > configuration file. At the LILO prompt, enter the name of the
> kernel
> > > you want (Usually 'linux' unless you changed it) followed by mem=##M.
> The ##
> > > is the amount of memory you have in
> > > > megabytes. REMEMBER to subtract 1 MB for the part taken by the
> > > graphics chip; otherwise your kernel will die during boot-up. If it
> still
> > > dies, subtract another 1MB; this could be taken
> > > > by vendor specific BIOS needs. If your distribution has a
> graphical
> > > boot screen, boot parameters may not be possible. You may still be able
> to
> > > edit the lilo.conf as is detailed below.
> > > >
> > > > LILO: linux mem=63M
> > > >
> > > >
> > > > After you know this works you should add it to LILO permanently
> by
> > > editing the lilo.conf file. This file is usually located at
> /etc/lilo.conf.
> > > After the line 'label=linux' (Or whatever you
> > > > called your kernel) add a line like:
> > > >
> > > > append="mem=63M"
> > > >
> > > >
> > > > Change the 63M above to be the amount of RAM you have - 1M. Save
> this
> > > file and as root reinstall LILO by running:
> > > >
> > > > /sbin/lilo
> > > >
> > > >
> > > > This should reinstall your boot loader and you will automatically
> > > tell the kernel how much RAM you have on your next reboot. If you are
> > > currently running with the correct amount of RAM
> > > > you do not need to reboot. If at a future date, you change the
> amount
> > > of RAM in your system you will need to repeat the above procedure.
> > > >
> > > > If you are loading your kernel without using LILO consult the
> > > loader's documentation for how to supply 'kernel parameters' when
> booting
> > > the kernel. Add the 'mem=##M' parameter in
> > > > that fashion.
> > > >
> > > >
> > > >
> > > > X Server Installation:
> > > >
> > > > 1.Find your XFree86 version. To determine what version of X your
> > > distribution has installed you can run:
> > > >
> > > > X -version
> > > >
> > > >
> > > >
> > > >
> > > > 2.Install XFree86 3.3.5. If you do not have it already, you will
> need
> > > to download and install XFree86 version 3.3.5. If your distribution came
> > > with a version of XFree86 earlier than 3.3.5
> > > > your should check to see if an upgrade is available from your
> distrib
> > > ution's web site. If your distribution does not have an upgrade
> available
> > > you can download it directly from the
> > > > XFree86.org web site.
> > > > When installing XFree86 you should use the vga16 server. The
> maximum
> > > resolution with this "compatibility" server will be 640x480x16. After
> you
> > > have successfully installed the vga16
> > > > server you can upgrade your install with the XFCom-I810 X server
> > > which will support high resolution modes.
> > > >
> > > > 3.Download XFCom-I810 and agpgart. Download the XFree86 3.3.5
> > > accelerated X server for the Intel® 810 Chipset (XFCom-i810) from
> > > support.intel.com. This is available in either
> > > > RPM or tar formats; choose the one your distribution supports.
> > > > You will also need to download the agpgart.o source. This is
> > > available in either a source RPM or a tar format; choose the one you
> > > distribution supports.
> > > >
> > > >
> > > > 4.Install XFCom-I810. You will need to be root to do this.
> > > > RPM:
> > > >
> > > > cd /path_to_downloaded_rpms
> > > > rpm -Uvh XFCom-i810*.i386.rpm
> > > >
> > > >
> > > >
> > > > TAR:
> > > >
> > > > cd /path_to_downloaded_tars
> > > > mkdir temp_XFCom
> > > > cd temp_XFCom
> > > > tar -zxpvf ../XFCom-i810*.tar.gz
> > > > ./INSTALL
> > > >
> > > >
> > > >
> > > >
> > > > 5.Compile and install the kernel module. The kernel module must be
> > > compiled before it can be installed. This module will need to be
> recompiled
> > > and reinstalled if you upgrade your kernel
> > > > at a later date, so keep the source in a safe place.
> > > > RPM:
> > > >
> > > > cd /path_to_downloaded_rpms
> > > > rpm --rebuild I810Gtt*.src.rpm
> > > > # Look for the output near the bottom that says where the
> rpm
> > > > # was built. Use that rpm name in the next command if you
> are
> > > > # not on a RedHat system.
> > > > rpm -Uvh /usr/src/redhat/RPMS/i386/I810Gtt*.i386.rpm
> > > >
> > > >
> > > >
> > > > TAR:
> > > >
> > > > cd /path_to_downloaded_tars
> > > > mkdir temp_i810
> > > > cd temp_i810
> > > > tar -zxpvf ../I810Gtt*.src.tar.gz
> > > > make
> > > > make install
> > > > # You may remove the temp_i810 and its contents if you
> wish.
> > > >
> > > >
> > > >
> > > >
> > > > 6.Edit the XF86Config file. Setup your XF86Config file. Use your
> > > favorite text editor to edit the file /etc/X11/XF86Config. You will need
> to
> > > be root to do this. You may want to do a 'man
> > > > XF86Config' on your Linux box first to understand this file.
> > > >
> > > > Monitor Section
> > > > Each Mode that you would like to use must be defined in the
> > > XF86Config file under the "Monitor" section. They are defined in one of
> the
> > > two following formats.
> > > >
> > > > Modeline "name" ...
> > > >
> > > > #or
> > > >
> > > > Mode
> > > > ...
> > > > EndMode
> > > >
> > > >
> > > > These should be set up according to what your monitor can
> support.
> > > Most distributions do this during the install process. If your
> distribution
> > > does not include all the modes you would like
> > > > to use, check the References section for information on creating
> > > these.
> > > >
> > > > Device Section
> > > > Add the following device section to your XF86Config file. There
> > > should be other similar device sections already in the file. You can add
> > > this to the file without changing other device
> > > > sections.
> > > >
> > > > Section "Device"
> > > > Identifier "i810"
> > > > EndSection
> > > >
> > > >
> > > >
> > > > Screen Section
> > > > Add this screen section, you should remove any other "svga"
> screen
> > > sections that may be in this file. Do not remove the vga16 screen
> section,
> > > as it would be useful if you should ever
> > > > need to fall back to vga mode. You must edit the Monitor line to
> > > reflect the Monitor you have. You can get this from another "Screen"
> section
> > > in this file, or from the "Monitor" section of
> > > > the XF86Config file. Be careful not to specify modes that your
> > > Monitor cannot support; you could damage the Monitor.
> > > >
> > > > Section "Screen"
> > > > Driver "svga"
> > > > Device "i810"
> > > > Monitor "Your_Monitor_Here"
> > > > Subsection "Display"
> > > > Depth 8
> > > > Modes "640x480" "800x600" "1024x768" "1152x864"
> > > "1280x1024" "1600x1200"
> > > > ViewPort 0 0
> > > > EndSubsection
> > > > Subsection "Display"
> > > > Depth 16
> > > > Modes "640x480" "800x600" "1024x768" "1152x864"
> > > "1280x1024" "1600x1200"
> > > > ViewPort 0 0
> > > > EndSubsection
> > > > Subsection "Display"
> > > > Depth 24
> > > > Modes "640x480" "800x600" "1024x768" "1152x864"
> > > "1280x1024"
> > > > ViewPort 0 0
> > > > EndSubsection
> > > > EndSection
> > > >
> > > >
> > > > Note: Edit the "Modes" lines to have only the resolutions you
> want
> > > for each Color depth. In this configuration your desktop will be as
> large as
> > > the largest supported mode in the line. Your
> > > > viewable area is the only thing that changes giving you a 'zoom'
> > > affect. If this is not what you want make sure the largest mode on each
> line
> > > is the mode you plan on using for your
> > > > desktop, the other modes can be available in case you need a low
> > > resolution mode for a game or application. You can also remove an entire
> > > Subsection (Including the Subsection
> > > > "Display" and "EndSubSection" lines) if you do not want to be
> able to
> > > use that color depth.
> > > >
> > > > 7.Set up the X server link. You will need to be root to do this.
> Since
> > > distributions set this up in differing manners, two methods have been
> > > included below. If neither of these work, you will
> > > > need to contact your distribution to get more complete setup
> > > information.
> > > >
> > > > Case 1: /etc/X11/X exists.
> > > >
> > > > ls -l /etc/X11/X
> > > > #If this does not exist use case 2.
> > > > ln -sf /usr/X11R6/bin/XFCom_i810 /etc/X11/X
> > > >
> > > >
> > > > Case 2: /usr/X11R6/bin/X exists AND points to your current X
> > > server.
> > > >
> > > > ls -l /usr/X11R6/bin/X
> > > > #If this does not exist and case 1 didn't exist,
> contact
> > > > #your distribution for assistance.
> > > > ln -sf /usr/X11R6/bin/XFCom_i810 /usr/X11R6/bin/X
> > > >
> > > >
> > > >
> > > >
> > > > 8.Start the X server. If you are already running X you will need to
> > > exit and start again. If you are set up to start X automatically then
> you
> > > will want to restart it by doing a
> > > > "CTRL-ALT-Backspace". If X is not running you should start it
> with a
> > > command like this:
> > > >
> > > > startx -- -bpp 16
> > > >
> > > >
> > > > The "-bpp 16" tells the server to start in 16 bit depth. You
> could
> > > also use 8 or 24 bit depth.
> > > > "CTRL-ALT-KeyPadPlus" and "CTRL-ALT-KeyPadMinus" will rotate
> through
> > > the resolutions available at the current color depth. For additional
> > > documentation on XFree86 or the
> > > > XF86Config file please visit the References.
> > > >
> > > >
> > > >
> > > >
> > > > Compiling X from Source:
> > > >
> > > > NOTE! This is for experienced Linux* users only. Provided below
> are
> > > only the details needed for patching and compiling the source;
> additional
> > > expertise is necessary to correctly install
> > > > X on your system. If you already have XFree86 3.3.5 correctly
> > > installed, compiling and installing the XFCom-i810 binary should not be
> > > difficult.
> > > >
> > > > 1.Download the source for the X server from XFree86.org. You will
> need
> > > these files, do not untar them, simply put them in a temp directory.
> (Note
> > > that this is 40+ MB of source)
> > > > X335src-1.tgz
> > > > X335src-2.tgz
> > > > X335src-3.tgz
> > > >
> > > >
> > > > 2.Download the patch from support.intel.com. This file should be
> called
> > > XFCom-i810-3.3.5.patch.tar.gz
> > > >
> > > > 3.Patch and build the source. Untar the patch into the same
> directory
> > > you placed the X335* files in and run the build-i810.sh script.
> > > >
> > > > cd path to X335*
> > > > tar -zxpvf XFCom-i810-3.3.5.patch.tar.gz
> > > > ./build-i810.sh
> > > >
> > > >
> > > > This will build the entire X tree by doing a 'make World'. You
> can
> > > find the correctly compiled XF86_SVGA server with i810 support located
> in
> > > the directory
> > > > XFree3.3.5/xc/programs/Xserver/. This is the same binary shipped
> as
> > > XFCom-i810 in the binary only distributions. Provided you already have
> > > XFree86 3.3.5 installed you should be able
> > > > to use this binary by placing it in the correct location and
> setting
> > > up your links/XF86Config file as detailed above. If you do not have
> XFree86
> > > 3.3.5 installed you should see the References
> > > > for help.
> > > >
> > > >
> > > >
> > > >
> > > > References:
> > > >
> > > > XFree86 FAQ http://www.xfree86.org/FAQ
> > > > XFree86 3.3.5 configuration
> http://www.xfree86.org/3.3.5/Config.html
> > > > XFree86-HOWTO http://metalab.unc.edu/mdw/HOWTO/XFree86-HOWTO.html
> > > >
> > > >
> > > >
> > > > Know Issues:
> > > >
> > > > When using specific mode timings the last scan line of the
> display
> > > can become corrupted.
> > > > Workaround: This is due to the HSyncStart value of the modeline.
> You
> > > can either use a different mode from your XF86Config file or adjust the
> > > modeline that is bad. The XSyncStart value
> > > > needs to be raised, xvidtune can be used to find the appropriate
> > > timing. Note, if you do not know that your monitor can handle the
> settings
> > > do not change them. You could damage the
> > > > monitor.
> > > >
> > > >
> > > >
> > > > Revision History
> > > >
> > > > 1.0.0 First revision, patched against XFree86 3.3.5. Full XAA
> > > support. 8,16,24 bit accelerated modes.
> > > >
> > > >
> > > >
> > > > Until the next time,
> > > >
> > > > Tom Kwasnik
> > > >
> > > > > Thanks Tom,
> > > > >
> > > > > Ive got the Mandrake 6.5 release.
> > > > > Can you please give me the url to this site where intel has this
> info?
> > > > > I origionally emailed Jetway who gave me an intel site and Ive
> looked
> > > thru
> > > > > it and not found anything that helps me. I may be looking in the
> wrong
> > > > > place.
> > > > >
> > > > > Thanks for helping me. I consider myself to be quite clued up on
> > > windows,
> > > > > but I feel so dumb trying to figure this linux out. Hell, this is
> just
> > > the
> > > > > start, Ive still got to configure my sound and internet connections
> > > after.
> > > > > Im not going to give up though. All this hunting around trying to
> find
> > > > > answers is helping me learn more as I go.
> > > > >
> > > > > regards
> > > > > Gina
> > > > >
> > > > > ----- Original Message -----
> > > > > From: "Tom Kwasnik" <[EMAIL PROTECTED]>
> > > > > To: "Gina" <[EMAIL PROTECTED]>
> > > > > Sent: Tuesday, 18 January 2000 02:02: pm
> > > > > Subject: Re: [newbie] X configure help PLEASE
> > > > >
> > > > >
> > > > > > On Mon, 17 Jan 2000, you wrote:
> > > > > > Hi Gina,
> > > > > > what is your distribution (Mandrake, RedHat, Caldera, etc....)?
> And
> > > > > > did you read the release notes published online there by Intel??
> they
> > > seem
> > > > > to
> > > > > > have gotten quite comprehensive in their description of how to set
> up
> > > the
> > > > > i810
> > > > > > chipset for use with linux...let me know if you still need
> assistance
> > > > > >
> > > > > >
> > > > > > Tom
> > > > > >
> > > > > > > Hi, >
> > > > > > > I know there are are already previous posts regarding this
> problem
> > > but I
> > > > > > > have tried everything Ive read so far and still Im at a loss and
> > > would
> > > > > > > appreciate someone helping me out if they know what should be
> > > selected
> > > > > for
> > > > > > > my particular video card. Its easy to say "go setup through x
> > > > > configure"
> > > > > > > but when I do that I always get a screen that only shows the top
> > > right
> > > > > of
> > > > > > > the screen with a horrible low colour depth, all dotted, and the
> > > rest
> > > > > goes
> > > > > > > off the monitor and I cant scroll or do anything. I have
> managed to
> > > get
> > > > > to
> > > > > > > a slightly smaller text mentioned below but this also has a
> horrible
> > > low
> > > > > > > colour depth and isnt a better resolution.
> > > > > > >
> > > > > > > My computer details:
> > > > > > > Jetway 910af motherboard
> > > > > > > pentium III 500, 64Mg RAM
> > > > > > > intel 82810 and 82C810AB and 82C802AB chipset
> > > > > > > (Intel (R) 810 Chipset Graphics Driver PV1.1)
> > > > > > > Intel GMCH built-in On board high performance AGP VGA
> > > > > > > (Memory being resizable using just what is needed depending on
> what
> > > is
> > > > > > > running.)
> > > > > > > Integrated hig performance & high quality 2D/3D engine
> > > > > > > Integrated programmable 24bit true-colour RAMDAC upto 230Mhz
> pixel
> > > > > clock.
> > > > > > > Panasonic E70 17" monitor (TX-T7F22)
> > > > > > > Horizontal specs - 30-70
> > > > > > > vertical specs - 50-180
> > > > > > > VGA, SVGA, VESA compatible
> > > > > > > max res - 1280x1024 - 60 Hz
> > > > > > > Max pixel clock - 108 mHz
> > > > > > >
> > > > > > >
> > > > > > > The best I can get from running x config is using these
> settings:
> > > > > > >
> > > > > > > choose a card - unsupported compatible VGA
> > > > > > > pick a server - SVGA
> > > > > > > monitor setup - custom
> > > > > > > H range - non interlaced SVGA 1024x768 @60, 800x600@...
> > > > > > > Video memory - 1MB
> > > > > > > 40-150
> > > > > > >
> > > > > > > I select multiple screen resolutions and when I go into linux
> the
> > > ctrl
> > > > > alt +
> > > > > > > doesnt work either.
> > > > > > > I still get the horrible low colour depth and 640 like
> resolution
> > > but
> > > > > its a
> > > > > > > little smaller enabling more to fit on the screen.
> > > > > > >
> > > > > > > Ive read through email lists, faqs, support, and I see many
> others
> > > with
> > > > > the
> > > > > > > same problem and not getting anywhere as all they get back is
> "use
> > > the
> > > > > > > xconfig..." I have tried it so many times Im starting to get
> rather
> > > > > > > frustrated with this and would really appreciate someone helping
> me
> > > out.
> > > > > > >
> > > > > > > I do have a patch from Intel and a driver for intel. But Im
> not
> > > > > familiar
> > > > > > > with linux (yet!) and dont even know how to run either of them!
> > > dumb
> > > > > huh!
> > > > > > >
> > > > > > > Gina
