Yes, fluid seems to be coing up the divot in the center where the clutch rod fits in. I will try to pull it apart tomorrow.
On Fri, Feb 24, 2012 at 7:46 PM, Kyle Munz <[email protected]> wrote: > The fluid is coming out of the center of the piston? It shouldn't be doing > that. I seem to remember it had a divot for the clutch rod to fit in, but > it shouldn't be a hole all the way through for fluid to escape. If you have > a pinhole there that would explain the slow loss of your clutch, and yeah, > the fluid would be going where it shouldn't be. > > -Kyle > > > On Fri, Feb 24, 2012 at 6:39 PM, Ralf Oehlerich <[email protected]>wrote: > >> It would not even move. Just kept leaking fluid through the center hole. >> The seals are probably shot. I ordered a rebuild kit. Now, just a few hours >> later, I have no pressure on the clutch handle at all. Where is the fluid >> going? Into the engine? No drips on the floor that I can see. >> >> >> On Fri, Feb 24, 2012 at 7:08 PM, Kyle Munz <[email protected]> wrote: >> >>> Once the slave is removed from the side of the bike you can use the >>> hydraulic pressure of the line to help press it out. Heating it may help >>> too. >>> >>> -Kyle >>> >>> >>> On Fri, Feb 24, 2012 at 5:17 PM, Ralf Oehlerich <[email protected]>wrote: >>> >>>> I cannot find the right one on eBay so I will order the rebuild kit. >>>> Not sure how I would get the cylinder out, since it is not moving, but I >>>> will figure it out. >>>> >>>> >>>> On Fri, Feb 24, 2012 at 6:10 PM, Kyle Munz <[email protected]> wrote: >>>> >>>>> I don't know if I would go to ebay for one of those. They are fairly >>>>> easy to rebuild and new parts can still be found fairly cheap. >>>>> >>>>> -Kyle >>>>> On Feb 24, 2012 4:54 PM, "Ralf Oehlerich" <[email protected]> >>>>> wrote: >>>>> >>>>>> I did have the cap off. I am bleeding it with a manual bleeding pump. >>>>>> I let it sit and now the clutch does not even dis-engage at all. I think >>>>>> the slave cylinder is leaking. When I had the slave cylinder off and >>>>>> pumped >>>>>> the clutch, fluid started coming out the center. I know that should not >>>>>> be. >>>>>> I will get another one on Fleebay. >>>>>> >>>>>> On Fri, Feb 24, 2012 at 5:27 PM, home <[email protected]> wrote: >>>>>> >>>>>>> i hope your using dot 3 or 4? do you have the reservoir over >>>>>>> filled? r u bleeding it with the cap off(as u should b)? then let her >>>>>>> sit >>>>>>> a day or so and bleed it again? periodically cycle the lever. >>>>>>> >>>>>>> On Fri, Feb 24, 2012 at 5:21 PM, Ralf Oehlerich < >>>>>>> [email protected]> wrote: >>>>>>> >>>>>>>> I just installed a used Clutch master cylinder on my 83 NH650 and >>>>>>>> the clutch does not dis-engage the gears completely. I can hold the >>>>>>>> bike in >>>>>>>> gear with the clutch pulled, but I cannot shift it back into Neutral. I >>>>>>>> have to turn the bike off to do that. Is there any way to adjust the >>>>>>>> clutch >>>>>>>> travel? I flushed the system properly and the clutch grabs as soon as >>>>>>>> you >>>>>>>> let it come out just a little. >>>>>>>> >>>>>>>> Thanks, >>>>>>>> >>>>>>>> -- >>>>>>>> You received this message because you are subscribed to the Google >>>>>>>> Groups "Nighthawk Motorcycle Lovers!" group. >>>>>>>> To post to this group, send email to >>>>>>>> [email protected]. >>>>>>>> To unsubscribe from this group, send email to >>>>>>>> [email protected]. >>>>>>>> For more options, visit this group at >>>>>>>> http://groups.google.com/group/nighthawk_lovers?hl=en. >>>>>>>> >>>>>>> >>>>>>> -- >>>>>>> You received this message because you are subscribed to the Google >>>>>>> Groups "Nighthawk Motorcycle Lovers!" group. >>>>>>> To post to this group, send email to >>>>>>> [email protected]. >>>>>>> To unsubscribe from this group, send email to >>>>>>> [email protected]. >>>>>>> For more options, visit this group at >>>>>>> http://groups.google.com/group/nighthawk_lovers?hl=en. >>>>>>> >>>>>> >>>>>> -- >>>>>> You received this message because you are subscribed to the Google >>>>>> Groups "Nighthawk Motorcycle Lovers!" group. >>>>>> To post to this group, send email to >>>>>> [email protected]. >>>>>> To unsubscribe from this group, send email to >>>>>> [email protected]. >>>>>> For more options, visit this group at >>>>>> http://groups.google.com/group/nighthawk_lovers?hl=en. >>>>>> >>>>> -- >>>>> You received this message because you are subscribed to the Google >>>>> Groups "Nighthawk Motorcycle Lovers!" group. >>>>> To post to this group, send email to [email protected] >>>>> . >>>>> To unsubscribe from this group, send email to >>>>> [email protected]. >>>>> For more options, visit this group at >>>>> http://groups.google.com/group/nighthawk_lovers?hl=en. >>>>> >>>> >>>> -- >>>> You received this message because you are subscribed to the Google >>>> Groups "Nighthawk Motorcycle Lovers!" group. >>>> To post to this group, send email to [email protected]. >>>> To unsubscribe from this group, send email to >>>> [email protected]. >>>> For more options, visit this group at >>>> http://groups.google.com/group/nighthawk_lovers?hl=en. >>>> >>> >>> -- >>> You received this message because you are subscribed to the Google >>> Groups "Nighthawk Motorcycle Lovers!" group. >>> To post to this group, send email to [email protected]. >>> To unsubscribe from this group, send email to >>> [email protected]. >>> For more options, visit this group at >>> http://groups.google.com/group/nighthawk_lovers?hl=en. >>> >> >> -- >> You received this message because you are subscribed to the Google Groups >> "Nighthawk Motorcycle Lovers!" group. >> To post to this group, send email to [email protected]. >> To unsubscribe from this group, send email to >> [email protected]. >> For more options, visit this group at >> http://groups.google.com/group/nighthawk_lovers?hl=en. >> > > -- > You received this message because you are subscribed to the Google Groups > "Nighthawk Motorcycle Lovers!" group. > To post to this group, send email to [email protected]. > To unsubscribe from this group, send email to > [email protected]. > For more options, visit this group at > http://groups.google.com/group/nighthawk_lovers?hl=en. > -- You received this message because you are subscribed to the Google Groups "Nighthawk Motorcycle Lovers!" group. To post to this group, send email to [email protected]. To unsubscribe from this group, send email to [email protected]. For more options, visit this group at http://groups.google.com/group/nighthawk_lovers?hl=en.
