Please,
can anyone tell me where to turn off software arcs? It's only in Gerber
generator engine or in Camtastic too? I've the same problem importing gerber
produced by Mentor's CAD...
----- Original Message -----
From: "Brad Velander" <[EMAIL PROTECTED]>
To: "Protel EDA Discussion List" <[email protected]>
Sent: Wednesday, September 28, 2005 6:42 PM
Subject: RE: [PEDA] arcs in Gerber go the wrong way
No Brian,
Wasn't a milling issue, I used purpose written software for that and never
had any issues with the milling. It was some form of a goofy error.
Something like the errant arcs we are talking about. Whatever it was I
couldn't get it to go away and finally stumbled onto turning off the
software arcs.
Sincerely,
Brad Velander
Senior PCB Designer
Northern Airborne Technology
#14 - 1925 Kirschner Road,
Kelowna, BC, V1Y 4N7.
tel (250) 763-2329 ext. 225
fax (250) 762-3374
-----Original Message-----
From: Brian Guralnick [mailto:[EMAIL PROTECTED]
Sent: Wednesday, September 28, 2005 9:21 AM
To: Protel EDA Discussion List
Subject: Re: [PEDA] arcs in Gerber go the wrong way
Brad,
Did need to do a milling of the PCB? I do know that true ARCs used to
be prefered for the way some of the older milling software which needed to
interperet out an extra smooth outline for the cutter.
_________
Brian G.
----- Original Message -----
From: "Brad Velander" <[EMAIL PROTECTED]>
To: "Protel EDA Discussion List" <[email protected]>
Sent: Wednesday, September 28, 2005 12:01 PM
Subject: RE: [PEDA] arcs in Gerber go the wrong way
Leo,
No the simple clearance issue is not what I had run into. It's been a while
so it is bugging me trying to remember precisely what did occur with the
software arcs enabled that had me turn them off from then on.
Sincerely,
Brad Velander
Senior PCB Designer
Northern Airborne Technology
#14 - 1925 Kirschner Road,
Kelowna, BC, V1Y 4N7.
tel (250) 763-2329 ext. 225
fax (250) 762-3374
-----Original Message-----
From: Leo Potjewijd [mailto:[EMAIL PROTECTED]
Sent: Tuesday, September 27, 2005 11:04 PM
To: Protel EDA Discussion List
Subject: RE: [PEDA] arcs in Gerber go the wrong way
At 28/09/05 01:07, Brad Velander wrote:
I can't recall at the moment what exactly I ran into but Software
Arcs did cause me a problem at one point. Since then I never turn
them on. (Haven't seen the problem again so I have forgotten what
the precise problem was.)
In a nutshell: they mess up your clearance. Start and endpoints of
the individual segments are OK because they sit on the true arc but
the line segments in between violate your clearance, literally by
cutting corners.....
Leo Potjewijd
hardware designer
____________________________________________________________
You are subscribed to the PEDA discussion forum
To Post messages:
mailto:[email protected]
Unsubscribe and Other Options:
http://techservinc.com/mailman/listinfo/peda_techservinc.com
Browse or Search Old Archives (2001-2004):
http://www.mail-archive.com/[email protected]
Browse or Search Current Archives (2004-Current):
http://www.mail-archive.com/[email protected]
____________________________________________________________
You are subscribed to the PEDA discussion forum
To Post messages:
mailto:[email protected]
Unsubscribe and Other Options:
http://techservinc.com/mailman/listinfo/peda_techservinc.com
Browse or Search Old Archives (2001-2004):
http://www.mail-archive.com/[email protected]
Browse or Search Current Archives (2004-Current):
http://www.mail-archive.com/[email protected]
____________________________________________________________
You are subscribed to the PEDA discussion forum
To Post messages:
mailto:[email protected]
Unsubscribe and Other Options:
http://techservinc.com/mailman/listinfo/peda_techservinc.com
Browse or Search Old Archives (2001-2004):
http://www.mail-archive.com/[email protected]
Browse or Search Current Archives (2004-Current):
http://www.mail-archive.com/[email protected]
--
No virus found in this incoming message.
Checked by AVG Anti-Virus.
Version: 7.0.344 / Virus Database: 267.11.6/111 - Release Date: 23/09/2005
____________________________________________________________
You are subscribed to the PEDA discussion forum
To Post messages:
mailto:[email protected]
Unsubscribe and Other Options:
http://techservinc.com/mailman/listinfo/peda_techservinc.com
Browse or Search Old Archives (2001-2004):
http://www.mail-archive.com/[email protected]
Browse or Search Current Archives (2004-Current):
http://www.mail-archive.com/[email protected]
