Hi Jakub, It's too bad that AD6 isn't a possibility for you, as a multi-channel design is *much* easier with AD6. Otherwise a lot of manual intervention is required. You might check out the multi-channel design demo's just to see what AD6 could do for you in this area: http://www.altium.com/webdemos/?p=10 http://www.altium.com/Evaluate/DEMOcenter/AltiumDesigneroverview/Multichanneldesign/
I don't recall 99SE auto-generating the sheets for you here, I think you had to copy/paste a sheet to make the new sheets. Then manually edit all of the ref des so there were no duplicates. Somewhat painful in 99SE. A piece of cake in AD. ---Phil Stevens Wednesday, November 1, 2006, 8:22:19 AM, you wrote: > Well, assume that AD6 is far away from horizon of my possibilities... :) > I have put 20x Symbols to main schema and changed symbols' names and now > the problem is to generate appropriate netlist and then user my pre-made > PCB. Is that possible? > Dennis Saputelli napisal(a): >> GET AD6 >> :) >> it really handles this pretty well >> >> in 99SE there are methods but at the end of the day i found that you >> really needed the 20 separate sheets >> and getting them to all annotate nicely was a major pain >> >> the 'repeat' feature was what finally drove me to AD6 >> >> Dennis Saputelli >> >> >> _______________________________________________________________________ >> CONTACT INFORMATION: >> _______________________________________________________________________ >> Integrated Controls, Inc. Tel: 415-647-0480 EXT 107 >> 2851 21st Street Fax: 415-647-3003 >> San Francisco, CA 94110 www.integratedcontrolsinc.com >> _______________________________________________________________________ >> NOTE! TO PASS OUR SPAM FILTER PUT THE FOLLOWING IN SUBJECT LINE: I.C.I. >> >> >> Jakub M. wrote: >> >>> [PROTEL 99 SE] >>> >>> In a device I want to put about 20 similar channels. Therefore I have >>> made a schema of a channel and have put it to main schema as a Sheet >>> Symbol 20 times. I have also made PCB for the single channel. >>> >>> Question: >>> >>> I want to generate netlist for the whole device and to use already made >>> PCB of channel (the same for all channels). How to do this? >>> >>> >>> Regadrs, >>> JM >>> >>> >>> >>> ____________________________________________________________ >>> You are subscribed to the PEDA discussion forum >>> >>> To Post messages: >>> mailto:[email protected] >>> >>> Unsubscribe and Other Options: >>> http://techservinc.com/mailman/listinfo/peda_techservinc.com >>> >>> Browse or Search Old Archives (2001-2004): >>> http://www.mail-archive.com/[email protected] >>> >>> Browse or Search Current Archives (2004-Current): >>> http://www.mail-archive.com/[email protected] >>> >>> >>> >> >> >> ____________________________________________________________ >> You are subscribed to the PEDA discussion forum >> >> To Post messages: >> mailto:[email protected] >> >> Unsubscribe and Other Options: >> http://techservinc.com/mailman/listinfo/peda_techservinc.com >> >> Browse or Search Old Archives (2001-2004): >> http://www.mail-archive.com/[email protected] >> >> Browse or Search Current Archives (2004-Current): >> http://www.mail-archive.com/[email protected] >> >> >> >> > > ____________________________________________________________ > You are subscribed to the PEDA discussion forum > To Post messages: > mailto:[email protected] > Unsubscribe and Other Options: > http://techservinc.com/mailman/listinfo/peda_techservinc.com > Browse or Search Old Archives (2001-2004): > http://www.mail-archive.com/[email protected] > > Browse or Search Current Archives (2004-Current): > http://www.mail-archive.com/[email protected] ____________________________________________________________ You are subscribed to the PEDA discussion forum To Post messages: mailto:[email protected] Unsubscribe and Other Options: http://techservinc.com/mailman/listinfo/peda_techservinc.com Browse or Search Old Archives (2001-2004): http://www.mail-archive.com/[email protected] Browse or Search Current Archives (2004-Current): http://www.mail-archive.com/[email protected]
