Dear experts,
I am measuring the fundamental and spurious emissions from an EUT ( with
interanl loop antenna) of fundamental frequencies of about 50kHz to 200kHz.
The measuring range of spurious emission is up to 1GHz.
The limits are according to a local standard from a local regulatory body.
All things being equal (and of course, they never are), I would expect that
a plasma display would be noisier. The scan rates of the two displays are
equal, but the voltages swings are larger for a plasma display. Plus the
power is much higher for a plasma display - just stand near one and you
will
In general, is it possible to say which one that has the lowest radiation?
Cheers!
#Amund Westin
Oslo / Norway
This message is from the IEEE Product Safety Engineering Society
emc-pstc discussion list.Website: http://www.ieee-pses.org/
To post a message to the list, send your e-mail to
melli...@tycoint.com wrote (in
<2141C5F52FD2CA4182AF6927090263B90F61B247@flbocexu04>) about 'Status of
EN 55022', on Tue, 21 Jun 2005:
>I know that over the last year there has been a lot of talk about the
>[quickly] upcoming EN 55022 requirements on the OJ.
>
>There had been some discussion reg
Derek,
The FCC specifies using a loop antenna for measuring field strength below
30 MHz. Extrapolation can be used if the field strength is measured at two
distances and the factor calculated (it will be close to 1/R^3), otherwise
the default of 40 dB/decade (1/R^2) must be used.
We normally us
Derek and Robert,
The fields from an electric dipole drop off as:
Magnetic: 1/r^2 and 1/r
Electric: 1/E^3, 1/E^2, and 1/E
For a magnetic dipole (loop):
Magnetic: 1/r^3, 1/r^2 and 1/r
Electric: 1/E^2, and 1/E
This link provides the formulas that will allow to to calculate the
field strength ve
Forgot!
E Fields from a true dipole do drop off at the inverse cube
rate also, It's just that the fields almost always get
referenced to a ground or ground plane which makes them
drop off for all practical purposes at the rate of the
inverse square.
- Robert -
> From: Y W Leung
>
Derek,
are your magnetic field measurements only in the range of 50 to 200 kHz? Or,
do you intend to measure to 1 GHz? If the former, you may need to modify your
300 to 10 meter scaling for specific frequencies between 50 and 200 kHz. I can
find you the formula for this. If the latter, you defini
Mr.. Leung,
At low frequencies, you may have undesirable effects from underground pipes /
etc... Or your EUT may be significantly large compared to the antenna to
influence the measurement. This makes the assumption of 3rd order rolloff
uncertain.
The FCC guidance is to measure at 2 distances
Near field?! You're way inside near field below 200KHz.
At those fundamental frequencies, you are correct.
Magnetic fields drop at the rate of inverse cube from a
dipole. You didn't say the size of the EUT. However, if it
is smaller than 1/5 the distance to the antenna, you can
correctly assume
Mr. Leung,
Here is an excerpt from the FCC Rules pertaining to measurements below 30 MHz
using a loop antenna.
"At frequencies below 30 MHz, measurements may be performed at a distance
closer
than that specified in the regulations; however, an attempt should be made to
avoid making
measureme
A limit specified at 300 meters is outside my experience. I have seen limits
at 1 m (military ), and 3, 10, and 30 meters (commercial). I'm not sure how to
extrapolate below 30 MHz where you are using the EMCO loop. But above 30 MHz
where you are only measuring electric field, the extrapolation i
I know that over the last year there has been a lot of talk about the
[quickly] upcoming EN 55022 requirements on the OJ.
There had been some discussion regarding updated versions being circulated
that would resolve some of the differences between CISPR 22 and EN 55022.
Does anyone know of the
Greetings fellow Group Members,
We are preparing to construct a new OATS and I am in the middle of generating
my requirements document.
I was wondering if any of you have any practical solutions to the flush
mounted AC mains receptacles - directly coupled to the horizontal ground
plane. Of cour
Dear colleagues;
I would like to thank all those who replied to my predicament regarding
emissions from an Ethernet port.
I have had some first-class advice which will help me solve the problem.
Many thanks;
Ian McBurney.
Allen & Heath Limited.
email: ian.mcbur...@allen-heath.com
***LEGAL DI
15 matches
Mail list logo