Is there a way one can write to the a user space variables from a bash
script
I have a current M144 that I'm using when call it looks up data in and table
then I want to return it in a variable so that the Gcode can use that data
I can make this work inside the gcode file but I would like to set
Thanks lut worked great I would never have thought to use it for this
-Original Message-
From: Jeff Epler [mailto:jep...@unpythonic.net]
Sent: Sunday, November 16, 2014 9:06 PM
To: Enhanced Machine Controller (EMC)
Subject: Re: [Emc-users] Hal mux
The "lut5" component can be used to imp
I'm working on a config with hal what I need is close to the mux is floating
point component but I only in bit form
I have 2 input devices that need to write to 1 pin
I want them to be able to select witch one writes to the pin from a Mcode
that can set the select pin
Pin 0 is connected mux2
esanet.com]
Sent: Wednesday, September 17, 2014 10:21 AM
To: Enhanced Machine Controller (EMC)
Subject: Re: [Emc-users] 5i25 configuration
On Wed, 17 Sep 2014, Kasey Matejcek wrote:
> Date: Wed, 17 Sep 2014 09:56:47 -0500
> From: Kasey Matejcek
> Reply-To: "Enhanced Machine Contr
configuration
On 17 September 2014 12:58, Kasey Matejcek wrote:
> I have tried flashing the firmware on it with the mesa utility
> prob_rfx2 and no change
You need to completely power-off the computer for the new firmware to show
up.
--
atp
If you can't fix it, you don
I have tried flashing the firmware on it with the mesa utility prob_rfx2 and
no change
I've even loaded hal manual loaded the driver and did a show for the pins
there were no stepgen pins listed include it after dmseg
Here is the complete dmesg
Print file information:
RUN_IN_PLACE=no
LINUXCNC_DI
I currently have a mesa 5i25 PCI card
I don't have and add on cards
I would like to connect 3 axis stepper machine to this card
When I run the pnconf wizard and select prob_rfx2 for firmware
Finish the wizard try to open the new machine I get error
hm2_5i25.0.stepgen.00.dirsetup not found
I've made a simple interface using and c8051f300 that will take a pwm signal
in and output signal to control and ESC rc motor controller
I was much cheaper than buying one to run my brushless motor for my spindle
work great
The project can be downloaded here http://www.lkm.bz/Anagol to pwm Esc.ra
Has anyone tried to play a video file from something like a Gopro camera is
there a enough power to play these type of files ?
Or isn't there enough video or cpu power to do this
I have costumer that is asking if I could put something together that would
play the files after their done recording an
Does anyone know of a lathe that needs repair or conversions to CNC in the
northern states I'm looking for a lathe that is a CNC or can be converted to
CNC
Somewhere close to Minnesota preferably
Doesn't have to be a working unit
-
Is there a way I can prevent my A axis from moving when I do a tool change
I have the TOOL_CHANGE_POSITION = 0 0 0 in the ini file I left the forth
zero off doesn't help
Right now I running a part and the A axis get wond up to 900 deg then it
does a tool change it unwinds it to zero
Then after t
I'll hook up a scope to it and check the phase on them
I've looked at one at a time so fare and there pretty clean on my 20mhz
scope
I'll get the 2 channel out and check both and the same time and phase
-Original Message-
From: Jon Elson [mailto:el...@pico-systems.com]
Sent: Sunday, July
]
Sent: Sunday, July 15, 2012 5:09 AM
To: Enhanced Machine Controller (EMC)
Subject: Re: [Emc-users] Spindle hooked to dc servo amp
On 15 July 2012 02:56, Kasey Matejcek wrote:
> No home made
> With optical pickup
The problem with a single-channel encoder is that if you double-count an
edge th
No home made
With optical pickup
-Original Message-
From: Jon Elson [mailto:el...@pico-systems.com]
Sent: Saturday, July 14, 2012 4:19 PM
To: Enhanced Machine Controller (EMC)
Subject: Re: [Emc-users] Spindle hooked to dc servo amp
Kasey Matejcek wrote:
> Still can get it stable the
] Spindle hooked to dc servo amp
Kasey Matejcek wrote:
> Found that the a,b signal were hook up backward it help a lot Still
> not smooth but operates close need more tunning now that it works
>
OK, great! That's what I should have suggested a while ago, took me a bit
to think thi
: Re: [Emc-users] Spindle hooked to dc servo amp
Kasey Matejcek wrote:
> Yes the ppmc.0.pwm.00-03.freq 5
> After playing some time I've come up with this it responds from 2 rpm
> to 14 rpm when you set s this give and accual spindle speed from about
> 35 to 75 rpm But ther
I've done as little as .0001
-Original Message-
From: andy pugh [mailto:bodge...@gmail.com]
Sent: Wednesday, July 11, 2012 7:15 AM
To: Enhanced Machine Controller (EMC)
Subject: Re: [Emc-users] Spindle hooked to dc servo amp
On 11 July 2012 13:07, Kasey Matejcek wrote:
> But
23:59:04 Kasey Matejcek did opine:
>
>
>> It set to 1000
>> setp ppmc.0.pwm.03.scale 1000
>>
>> when you watch ppmc.0.pwm.03.value it changes from 1000 to -1000 and
>> back and forth it goes when I set s 50 rpm then after some time
>> ppmc.0.pwm.03.
: Enhanced Machine Controller (EMC)
Subject: Re: [Emc-users] Spindle hooked to dc servo amp
On 10 July 2012 23:04, Kasey Matejcek wrote:
> setp pid.3.maxoutput 1000
What is the pwm scale? If that is 0-1 and your PID is 0-1000 then you will
have problems.
--
atp
If you can't fix it, you don&
3.output ppmc.0.pwm.03.value
-Original Message-
From: andy pugh [mailto:bodge...@gmail.com]
Sent: Tuesday, July 10, 2012 8:02 AM
To: Enhanced Machine Controller (EMC)
Subject: Re: [Emc-users] Spindle hooked to dc servo amp
On 10 July 2012 13:41, Kasey Matejcek wrote:
> I should not s
I should not say nothing but the spindle turns real aradic and there is no
rpm control don't matter were I set the p,I,g
-Original Message-
From: Kasey Matejcek [mailto:someo...@lkm.bz]
Sent: Tuesday, July 10, 2012 6:40 AM
To: 'Enhanced Machine Controller (EMC)'
Subject:
03:35, Kasey Matejcek wrote:
> But know I'm I have removed the a axis config setting and I'm trying
> to get it looped to the spindle controls and I can't seem to make that
> work
Are you wanting closed-lop spindle speed control, or will open-loop work?
Open-loop sho
I'm using a johns univ pico controller and his dc servo amps
I'm trying to use one of his amps to drive the dc servo motor on my lathe
I can't seem to understand what signals to connect
The amp is connected to ppmc.0.pwm.03 on his board and I've set p,I,g in the
config
If leave the default exam
I have a lathe setup using Jons Universal PWM controller and DC brush Amps
I want to set it up so the spindle can be used as an a axis
I was think of using the 4th servo port to control the spindle with one of
his amps.
the spindle has a 90v DC motor on it
the spindle has a 500 count increment
Has anyone tried to use and RC controller with EMC to run a RC brushless
motor
They take a pwm control signal from 1ms to 2ms or around there but haven't
tried
It sound like the have to have a signal on the input when there powered up
or the go into disable mode possibly
> On 7 November 2011 02:26
Is there a way in gcode that I can read what tool is loaded
I've got a sub built and works but there's a part in the sub I don't want
to run if a certain tool number is loaded
Is there a way to read hal variables in the gcode with the if statement?
-
Has anyone though about adding a line in the ini file for the M6 command so
one could run a file or even just the gcode commands so one may probe for
the tool height after the toolchange and store the height
Right now I have to add the line after each toolchange so this happens
It just would be n
This little item is what you looking for
The default code has a web browser in it and it has and on board temp sensor
that displays it's temp on a webpage
If you good at programing there some extra port that can be activated from
the webpage
http://mouser.com/search/ProductDetail.aspx?qs=qyjEHkudLH
If you need More of these I have 2 sets from a 13"X 13"
Decided it was easer to fix encoders to the back of the servo motors than to
use those style encoders
-Original Message-
From: sam sokolik [mailto:sa...@empirescreen.com]
Sent: Friday, April 16, 2010 9:02 AM
To: Enhanced Machine Cont
I've got a project to do on my 4 axis mill x,y,z,a running EMC
A is parallel to to the X axis and is a rotory head the part will between
centers on the x axis 28" long
The part file is a 3d model of a cylinder like shape egg shape
What cad program will work the best to output gcode for machinin
I've got a project to do on my 4 axis mill x,y,z,a running EMC
A is parallel to to the X axis and is a rotory head the part will between
centers on the x axis 28" long
The part file is a 3d model of a cylinder like shape egg shape
What cad program will work the best to output gcode for machinin
You can get samples to play with
I currently are using these in a weather van seem to be pretty accrate and
stable
www.newark.com cares them to but still $8.50
-Original Message-
From: Kirk Wallace [mailto:kwall...@wallacecompany.com]
Sent: Monday, March 08, 2010 4:19 PM
To: Enhanced Mac
I want to setup home using the index pulse from the encoder
I have Pico system servo controller version 2 running current firmware and
the current version of EMC
I must be missing something in hal that need to be turn on looked through
the examples
I even hooked up the index pulse to a nother i
Alex
- Original Message -
From: "Kasey Matejcek"
To:
Sent: Wednesday, January 07, 2009 4:15 AM
Subject: [Emc-users] Estop universal PWM
> Is there a way to have emc come out of estop and be in estop reset
>
> When I hit the reset button for the estop chain on my machine
>
&g
Is there a way to have emc come out of estop and be in estop reset
When I hit the reset button for the estop chain on my machine
Witch pin do I need to link to to make this happen I've messed around and
haven't got anywere to speak of
I tied ppmc.0din.14.in to estop-latch.0.reset this work som
Just issue a g92 x0 y0 z0 when the table is were you want it this sets it
the axis to 0
-Original Message-
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] On Behalf Of rtwas
Sent: Sunday, March 16, 2008 7:30 PM
To: Emc-users@lists.sourceforge.net
Subject: [Emc-users] manually setting "ho
Linksp something ppmc.0.out-05
This is what I did and seems to work
_
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] On Behalf Of Kasey Matejcek
Sent: Friday, December 22, 2006 8:35 PM
To: 'Enhanced Machine Controller (EMC)'
Subject: [Emc-users] M64 and M65 setup
need to control a port on the pico systems PMW servo controller using EMC 2
with a m code for locking device
I'd like to send a m64 P? to emc2 and have the relay's on controller work
like the spindle speed up or the spindle speed down
--
This message has been scanned for viruses and
dan
I've been using a touchscreen for a year now
Just set it up under the X windows setup as and input device does every
thing the same as the mouse
There are sevral how to on setting up touchscreens
-Original Message-
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] On Behalf Of Gene Hesket
39 matches
Mail list logo