Cisco Book, High Availability Networking with Cisco
I just bought the High Availability Networking with Cisco router and I must say it's OUTSTANDING. The author goes into many great topic's, that other books don't. I would encourage everyone to at least look at it. You can get online or your local book store Autor Vincent C. Jones ISBN # 0201704552 Brian _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: Ethernet address question
I found the answer to your question? what is ..0001 ? it a default IPX address that Netware gives it's servers. You can change this , if you want to. _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Two ISP's
I have one ISP with 192K going to the Internet and I am using NAT not PAT to resolve my UN-register to register to the Internet. I now want to add a differant ISP now to the same router, a full T/1. What are the pro's and con's to this? I need to keep the 192k for reason's but 100 share the 192K link and it's slow. I need to setup NAT on T/1 interface I know that? should I use policy routing coming from my LAN to the T/1? would this work? Brian _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Setting up E1 for a Sniffer?
HI all I have a problem here, I am running all my computers and servers to my switch. I have E1 open open on my Cisco 4000 router, I would like to configure my E1 interface so I can put my Sniffer on that interface, so I can capture all the packet comimg and going? Can someone tell me what is the pro's and con's of doing this and where I can find a sample configuration to setup the e1 interface. Thanks Brian _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: Sniffing on a LAN Switch
http://www.cisco.com/warp/public/473/41.html#intro http://www.cisco.com/univercd/cc/td/doc/product/lan/cat5000/rel_4_1/config/net mg.htm#xtocid59890 http://www.cisco.com/univercd/cc/td/doc/product/iaabu/pix/pix_v42/pix42cfg/pix 42cfg.htm#xtocid72980 http://www.cisco.com/univercd/cc/td/doc/product/lan/cat5000/rel_2_2/c5kcg2_2/1 1netmg.htm#xtocid269510 _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
promiscuous mode (NIC)
=A0Does anyone no of any good promiscuous tools? and how do you no your NIC=20= is=20 in or have a promiscuous NIC in your Computer _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
promiscuous mode (NIC)
Does anyone no of any good promiscuous tools? and how do you no your NIC is in or have a promiscuous NIC in your Computer _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Ethereal , A network protocol analyzer.
I would like to set this up? I just want to do simple packet captures? I am having problems setting up a network adapter under windows ME? Thanks Brian www.ethereal.com or ethereal.zing.org _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Windows Sniffer
Does anyone no of a good Windows sniffer? that is cheap and It does not crash.. _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Free Sniffer
http://www.cs.umd.edu/~cpopescu/NetAnalyzer/ _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: PCAnywhere problem with ISDN Connection
Why don't you try using Netmeeting, it's free. I would keep a ping running while your connected to the other side, while your using pcAnywhere, The connection might be dropping, lack of intresting traffic. _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Sniffer Program
Can someone recommend a good WindowsME sniffer? Brian _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Sniffer Program
=A0=A0Can someone recommend reasonable price Windows sniffer?=20 =A0=A0Brian _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Packet vs Byte
Everyone I am just wondering why IP Accounting and Sniffers us both Packet and Byte counters? Can someone explain this to me, why they use both and what are the difference's or seen me to a website? Brian _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
DLSW+ question
I am trying to setup two routers with DLSW+ , when I do with routing ,I can'= t=20 ping each other loopback interfaces for some reason.=20 Hostname DCE_Router dlsw local-peer peer-id 10.1.1.1 dlsw remote-peer 0 tcp 10.1.1.2 dlsw bridge-group 1 Loopback0 =A0 ip address 10.1.1.1 255.255.255.0 interface Ethernet0 ip address 150.1.1.1 255.255.255.0 bridge-group 1 interface Serial0 ip address 10.1.2.1 255.255.255.0 encapsulation ppp clockrate 64000 bridge 1 protocol ieee router eigrp 100 network 10.0.0.0 redistribute connected ___ Hostname DTE_Router dlsw local-peer peer-id 10.1.1.2 dlsw remote-peer 0 tcp 10.1.1.1 dlsw bridge-group 1 Loopback0 =A0 ip address 10.1.1.2 255.255.255.0 interface Ethernet0 ip address 160.1.1.2 255.255.255.0 bridge-group 1 interface Serial0 ip address 10.1.2.2 255.255.255.0 encapsulation ppp bridge 1 protocol ieee router eigrp 100 network 10.0.0.0 redistribute connected _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: Reverse Telnet to reset modem
http://www.cisco.com/univercd/cc/td/doc/product/software/ios120/12cgcr/dial_c/ dcrtelnt.htm _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: PPP over Frame-Relay
I got it to work, all I needed to do was to remove the =A0 ppp authenticatio= n=20 chap pap and it I could ping each other. Thanks Brian _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
PPP over Frame-Relay
Hi I am trying to make this PPP over Frame-Relay with two Cisco 2501 running 12.0.5(T) see below. For some reason this does not work? can someone please help me to get this to work, I have ran the debug commands and it seems like its working but I can not ping each other for some reason. I have both my config's below... Current configuration: ! version 12.0 service timestamps debug uptime service timestamps log uptime no service password-encryption service udp-small-servers service tcp-small-servers ! hostname DCE ! enable password brian ! username brian password 0 brian ! ! ! ! ip subnet-zero ! virtual-profile virtual-template 1 frame-relay switching cns event-service server ! ! ! interface Ethernet0 ip address 64.32.168.37 255.255.255.224 no ip directed-broadcast ! interface Virtual-Template1 ip address 10.1.1.1 255.255.255.0 no ip directed-broadcast no peer default ip address ppp authentication chap pap ! interface Serial0 no ip address no ip directed-broadcast encapsulation frame-relay clockrate 64000 frame-relay lmi-type ansi frame-relay intf-type dce ! interface Serial0.1 point-to-point no ip directed-broadcast frame-relay interface-dlci 32 ppp Virtual-Template1 ! interface Serial1 no ip address no ip directed-broadcast shutdown ! interface TokenRing0 no ip address no ip directed-broadcast shutdown ! no ip classless ip route 0.0.0.0 0.0.0.0 Virtual-Template1 no ip http server ! access-list 1 permit 10.1.1.1 ! ! line con 0 transport input none line aux 0 line vty 0 4 password pp login ! end DCE#sho ver Cisco Internetwork Operating System Software IOS (tm) 2500 Software (C2500-JS-L), Version 12.0(7)T, RELEASE SOFTWARE (fc2) Copyright (c) 1986-1999 by cisco Systems, Inc. Compiled Mon 06-Dec-99 17:10 by phanguye Image text-base: 0x0306C4E0, data-base: 0x1000 ROM: System Bootstrap, Version 5.2(8a), RELEASE SOFTWARE BOOTFLASH: 3000 Bootstrap Software (IGS-RXBOOT), Version 10.2(8a), RELEASE SOFTW ARE (fc1) DCE uptime is 5 minutes System returned to ROM by power-on System image file is "flash:c2500-120T.bin" cisco 2500 (68030) processor (revision E) with 8192K/2048K bytes of memory. Processor board ID 03897480, with hardware revision Bridging software. X.25 software, Version 3.0.0. SuperLAT software (copyright 1990 by Meridian Technology Corp). TN3270 Emulation software. 1 Ethernet/IEEE 802.3 interface(s) 1 Token Ring/IEEE 802.5 interface(s) 2 Serial network interface(s) 32K bytes of non-volatile configuration memory. 16384K bytes of processor board System flash (Read ONLY) Configuration register is 0x2102 DCE# DTE#sho run Building configuration... Current configuration: ! version 12.0 service timestamps debug uptime service timestamps log uptime no service password-encryption service udp-small-servers service tcp-small-servers ! hostname DTE ! enable password pp ! username brian password 0 brian ! ! ! ! ip subnet-zero ! virtual-profile virtual-template 1 cns event-service server ! ! ! interface Ethernet0 ip address 64.32.168.37 255.255.255.224 no ip directed-broadcast ! interface Virtual-Template1 ip address 10.1.1.2 255.255.255.0 no ip directed-broadcast ppp authentication chap pap ! interface Serial0 no ip address no ip directed-broadcast encapsulation frame-relay frame-relay lmi-type ansi ! interface Serial0.1 point-to-point no ip directed-broadcast frame-relay interface-dlci 32 ppp Virtual-Template1 ! interface Serial1 no ip address no ip directed-broadcast shutdown ! interface TokenRing0 no ip address no ip directed-broadcast shutdown ! no ip classless ip route 0.0.0.0 0.0.0.0 Virtual-Template1 no ip http server ! access-list 1 permit 10.1.1.2 ! ! line con 0 transport input none line aux 0 line vty 0 4 password pp login ! end DTE#ping 10.1.1.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 10.1.1.1, timeout is 2 seconds: .. Success rate is 0 percent (0/2) DTE#sho ip int brief Interface IP-Address OK? Method Status Prot ocol Ethernet0 64.32.168.37YES NVRAM up down Serial0unassigned YES NVRAM upup Serial0.1 unassigned YES unset upup Serial1unassigned YES NVRAM administratively down down TokenRing0 unassigned YES NVRAM administratively down down Virtual-Access110.1.1.2YES TFTP up down Virtual-Template1 10.1.1.2YES NVRAM down down DTE#sho ver Cisco Internetwork Operating System Software IOS (tm) 2500 Software (C2500-JS-L), Version 12.0(7)T, RELEASE SOFTWARE (fc2) Copyright (c) 1986-1999 by cisco Systems, Inc. Compiled Mon 06-Dec-99 17:10 by phanguye Image text-base: 0x0306C4E0, data-base: 0x1000 ROM: System Bootstrap, Version 5.2(8a), RELEASE SOFTWARE BOOTFLASH: 3000 Bootstrap Software
Dial Backup-up Question
=A0=A0=A0I have a few sites which for some reason I recieve many error's on=20= my=20 Serial Interface on and off. =A0Is there a way? if I recieve to many error's= ,=20 that I can have my ISDN or Analog modem kick off a dial-backup until the=20 errors stop what would my config look like?? Brian _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: Off Topic - CCNA in New England
Are you allowed to work in the USA? will the company sponsor you? _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Dial-Backup Question
I have a few sites which for some reason I recieve many error's on my Serial Interface on and off. Is there a way if I recieve to many error's, that I can have my ISDN or Analog modem kick off dial-backup until the errors stop Brian _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Dial backup Question
=A0=A0=A0I have a few sites which for some reason I recieve many error's on=20= my=20 Serial Interface on and off. =A0Is there a way? if I recieve to many error's= ,=20 that I can have my ISDN or Analog modem kick off a dial-backup until the=20 errors stop what would my config look like?? Brian _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: ISDN Simulator
I have a question here? should you have an administrative distance defined on your static route? ip route 1.1.1.1 255.255.255.255 BRI0 ??? 200 ip route 1.1.1.1 255.255.255.255 BRI0 X.X.X.X 200 The X.X.X.X is the next hop IP Address and the 200 is your administrative distance. _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: Using Register IP Address on your Private network
How does any application no if it's registerd or non-registered? or real address? _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: Using Register IP Address on your Private network
With the shortage of registerd addresses out there and 99 percent of all programs work with NAT. Then why are we wasting register addresses on private networks for? Brian _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Aux port running Slip protocol?
Can I setup a Cisco 25XX for slip dial-in access? _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: ISDN Simulator
Cisco has one for $150.00 , it's their CIM CD it's really good, almost real=20 and it has much more QA to. =A0www.cisco.com/go/cim =A0or =A0www.ciscopress.com/cim they have 6 CD's and= one of=20 them is the ISDN one. You can buy these CD's from any online book store. =A0=A0 _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Split-horizon using Frame-relay ( DECNET )
I have a question? why is it that I can't turn off split-horizon on a Multipoint sub frame-relay interface ( Hub Router ). I can only turn off Split-horizon on the serial interface it self? Can someone share with me a why to turn off split-horizon using Decnet on a Mulipoint frame-relay circuit? _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Enhanced Interior Gateway Routing Protocol
http://cio.cisco.com/warp/public/103/eigrp5.html _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Cisco CIM CD's
http://www.ciscopress.com/changeling.cfm?chnglng=16 Here is the website? you can get these Cd's at any book stores... Brian _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Loading flash image onto a 2600 and 3600 cisco router
Heres the procedure to do a xmodem. This will let you copy the image on to the flash on the 2600 and 3600 router. Please power cycle the router and depress Cntrl, Break within the first 60 seconds to go into rommon mode. rommon1confreg 0x3922 Turn router off Reset Hyperterminal setting to Speed 115200 Goto Call and disconnect Goto Call and connect Turn router on rommon1xmodem -c filename Do not start upload program yet... File size Checksum File name 2537948 bytes (0x26b9dc) 3640-boot-l WARN: This operation will ERASE bootflash. If the xmodem download to bootflash fails, you will lose any good image you may already have in bootflash. Invoke this application only for disaster recovery. Do you wish to continue? [yes/no]: yes Ready to receive file prog ... Goto transfer and send file Select xmodem protocol Click brouse and find the image Highlight it and click open Click send File starts to copy Erasing flash at 0x300 program flash location 0x300 Transfer complete! Commands for this are listed below Router will reload with new image Once at router prompt go into enable mode Go into config mode Go into console port configuration set speed to 9600 You will loose connection at this time Reset hyperterminal setting to speed 9600 Goto Call and disconnect Goto Call and connect end set config register to 0x2102 exit config Do sh ver and make sure config register is set to 0x2102 Reload router routeren router#config t router(config)#line con 0 router(config-line)#speed 9600 router(config-line)#end router(config)#config-register 0x2102 router(config)#exit router#sh ver router#reload _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Cisco Lab
During the real lab, what day does Cisco come in and mess up your network up? what kind of things have Cisco done to your network at the lab? Brian _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Appletalk over frame-relay
I am trying to configure 5 Cisco router's with appletalk, can someone out their send me a complete config list? Brian _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Appletalk over frame-relay
I am trying to configure 5 Cisco router's with appletalk, can someone out their send me a complete config list? Brian _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: Cost vs Metric
So what your telling me that the Cost is the same as the Metric? Cost, is it what the link is ( like Ethernet would be a 10? and a 56K circuit would be say 1000 ) and a metric would be the cost added upto the destination? or the best route to take. _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Cost vs Metric
Hello Can someone give me a brief descriptions between the both? the difference between Cost and Metric? Thanks _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
A Cheap sniffer , but a good one for Windows 98 asd ME
Does anyone no of a good home sniffer that is not going to break the bank, that would work well to learn and to do small network analyzing... _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
A good link about sniffers
http://www.protected.kiev.ua/index.html?sniffing-faq.htm _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
sniffer
Do you knnw of a good home sniffer that is not going to break the bank, that would work well to learn from and to do small network analyzing... Brian _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
OSPF HELP!!!!!!!!! Over Frame-Relay
I am working on OSPF case study with 4 routers, the one 4000 is setup as the frame-switch and the other 3 are the DTE routers ( 25XX) routers. I had setup EIGRP with no problem and now trying to get OSPF to work , but having some problems. RouterA is the core router . RouterB and RouterC are the field routers. I am having problems getting OSPF to work here, can someone please look at my config's and help me here. All the config's are in the body of this e-mail. Thanks version 11.2 service password-encryption no service udp-small-servers no service tcp-small-servers ! hostname RouterA ! enable password 7 140702 ! username jackie password 7 060A0E2F484F username brian password 7 00101A0B01 username tom privilege 12 password 7 105A001400 username jack password 7 001D1C13 ip name-server 172.1.1.3 ip dhcp-server 172.1.1.3 ! ! hub ether 0 1 link-test auto-polarity ! hub ether 0 2 link-test auto-polarity ! hub ether 0 3 link-test auto-polarity ! hub ether 0 4 link-test auto-polarity ! hub ether 0 5 link-test auto-polarity ! hub ether 0 6 link-test auto-polarity ! hub ether 0 7 link-test auto-polarity ! hub ether 0 8 link-test auto-polarity ! interface Loopback0 ip address 2.2.2.2 255.255.255.0 ! interface Ethernet0 ip address 10.1.1.1 255.255.255.0 ip helper-address 172.1.1.3 no cdp enable ! interface Serial0 no ip address encapsulation frame-relay ! interface Serial0.200 point-to-point ip address 192.1.1.1 255.255.255.0 ip accounting output-packets no cdp enable frame-relay interface-dlci 200 ! interface Serial0.210 point-to-point ip address 193.1.1.1 255.255.255.0 ip accounting output-packets no cdp enable frame-relay interface-dlci 210 ! interface Serial1 no ip address shutdown no cdp enable ! interface Async1 ip unnumbered Ethernet0 ip tcp header-compression encapsulation ppp async default routing async mode interactive peer default ip address pool tel dialer in-band dialer idle-timeout 600 dialer wait-for-carrier-time 120 dialer-group 1 no cdp enable ppp authentication chap callin ! router ospf 10 redistribute connected network 2.2.2.2 0.0.0.0 area 0 network 10.1.1.1 0.0.0.0 area 0 network 193.1.1.1 0.0.0.0 area 0 network 192.1.1.1 0.0.0.0 area 0 ! ip local pool tel 10.1.1.80 10.1.1.90 no ip classless logging console informational logging monitor informational logging 10.1.1.50 no cdp run ! snmp-server community public RW dialer-list 1 protocol ip permit privilege line level 15 ip privilege exec level 15 ping privilege exec level 15 show startup-config privilege exec level 15 show running-config privilege exec level 15 show privilege exec level 15 debug ! line con 0 line aux 0 exec-timeout 0 0 autoselect ppp login local modem InOut modem autoconfigure type usr_sportster transport input all stopbits 1 rxspeed 2400 txspeed 2400 line vty 0 4 exec-timeout 0 0 password 7 06161F login local ! end _ version 12.0 service timestamps debug uptime service timestamps log uptime no service password-encryption ! hostname RouterC ! logging buffered informational ! ip subnet-zero ip name-server 172.1.1.3 ip dhcp-server 172.1.1.3 ! ! ! interface Loopback0 ip address 3.3.3.3 255.255.255.0 no ip directed-broadcast ! interface Ethernet0 ip address 192.168.1.1 255.255.255.0 ip helper-address 172.1.1.3 no ip directed-broadcast no cdp enable ! interface Serial0 description :DLCI 210 ip address 193.1.1.2 255.255.255.0 ip directed-broadcast ip accounting output-packets encapsulation frame-relay no ip route-cache no ip mroute-cache no fair-queue frame-relay interface-dlci 210 ! interface Serial1 description : DLCI 100 no ip address no ip directed-broadcast no keepalive shutdown no cdp enable ! router ospf 10 redistribute connected network 3.3.3.3 0.0.0.0 area 0 network 192.168.1.1 0.0.0.0 area 0 network 193.1.1.2 0.0.0.0 area 0 default-information originate ! ip nat translation timeout never ip nat translation tcp-timeout never ip nat translation udp-timeout never ip nat translation finrst-timeout never ip nat translation syn-timeout never ip nat translation dns-timeout never ip nat translation icmp-timeout never no ip classless ! logging 10.1.1.50 no cdp run snmp-server community public RW ! line con 0 transport input none line aux 0 line vty 0 4 login ! end RouterC# _ RouterB# Current configuration: ! version 11.2 service timestamps log datetime service password-encryption no service udp-small-servers no service tcp-small-servers ! hostname RouterB ! enable password 7 021614 ! hub ether 0 1 link-test auto-polarity ! hub ether 0 2 link-test auto-polarity ! hub ether 0 3 link-test auto-polarity ! hub ether 0 4 link-test auto-polarity ! hub ether 0 5 link-test auto-polarity ! hub ether 0 6 link-test auto-polarity ! hub ether 0 7 link-test auto-polarity ! hub ether 0 8 link-test auto-polarity ! interface Loopback0 ip
OSPF over Frame-Relay
I have attach 4 Cisco router config's, how to setup a lab OSPF over Frame-relay.. Have fun Bottom router-config.ZIP
IP Browsers
Can anyone recommend a good IP Browser? I know Solarwinds.net has one , but is their any others out there. **NOTE: New CCNA/CCDA List has been formed. For more information go to http://www.groupstudy.com/list/Associates.html _ UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html FAQ, list archives, and subscription info: http://www.groupstudy.com Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Using Video over frame-relay
The company that I work for is going to be using about 200 video cam in the field. I have a 192K frame circuit going to the Internet. How will this effect my network and how can I prevent this streaming video from killing my network, and I would I improve it . Brian Email Address [EMAIL PROTECTED] **NOTE: New CCNA/CCDA List has been formed. For more information go to http://www.groupstudy.com/list/Associates.html _ UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html FAQ, list archives, and subscription info: http://www.groupstudy.com Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Video over frame-relay
The company that I work for is going to be using about 200 video cam in the field. I have a 192K frame circuit going to the Internet. How will this effect my network and how can I prevent this streaming video from killing my network, and how could I improve it . Brian Email Address [EMAIL PROTECTED] **NOTE: New CCNA/CCDA List has been formed. For more information go to http://www.groupstudy.com/list/Associates.html _ UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html FAQ, list archives, and subscription info: http://www.groupstudy.com Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
PPPoE
Is their a website that explains what PPPoE is? I know what it stands for. Brian Email Address [EMAIL PROTECTED] **NOTE: New CCNA/CCDA List has been formed. For more information go to http://www.groupstudy.com/list/Associates.html _ UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html FAQ, list archives, and subscription info: http://www.groupstudy.com Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
dividing up the same subnet on 2 diff segments
Hi I have a question? I have two routers okay and I have routing turned on (EIGRP). lets say I want to use 10.1.1.0 . I want to be able to to split this subnet into two networks, I know you use IP subnet-zero to do this, I want address the first router E0 Interface with 10.1.1.1 to 10.1.1.126 and the second router E0 with the second half 10.1.1.127 to 10.1.1.254 ok. Now I want to be able to ping each others gateway. Can I or should I be able to ping each others gateway and have one flat segment between 2 router Ethernet segments. Do I need to bridge this? I know this can be done, I was in class a while ago and my teacher explain to me how this would work, but it was a long time ago. RouterA Interface E0 ip address 10.1.1.1 255.255.255.128 RouterB Interface 10.1.1.128 255.255.255.128 Brian Email Address [EMAIL PROTECTED] ___ UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html FAQ, list archives, and subscription info: http://www.groupstudy.com Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
dividing up the same subnet on 2 diff segments
Hi I have a question? I have two routers okay and I have routing turned on both of them (EIGRP). lets say I want to use 10.1.1.0 and I want to be able to to split this subnet into two networks, I know you can use IP subnet-zero to do this, but I want to address the first router E0 Interface with 10.1.1.1 to 10.1.1.126 and the second router E0 with the second half 10.1.1.127 to 10.1.1.254 ok. Now I want to be able to ping each others gateway. Can I or should I be able to ping each others gateway and have one flat segment between 2 router Ethernet segment. Do I need to bridge this? these two segments together. Brian Email Address [EMAIL PROTECTED] ___ UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html FAQ, list archives, and subscription info: http://www.groupstudy.com Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Proxy-Server over 3 Subnets
I have this question about proxy-server? I have WIN98SE that has my dial-up to the Internet and I have proxy-server on this PC too , this is connected to one of my Cisco routers ; I have 3 router that are connected together running EIGRP IP only. I have 3 other pc's connected to each one my routers, not including my proxy-server ( 4 pc's in total) . The pc that is on the same subnet as the proxy-server works just fine, I had set all the right setting in my IE 5.0 for proxy-server for all of my pc's, but the other 2 pc's can not connect to the internet for some reason. I had done traces and pings to the proxy-server with no replays, but I can ping each other just fine. Does proxy-server only work on the same subnet as your workstation, that is going to use the Internet or is their a way for my other 2 pc's can utilize the proxy-server like the one that is on the same subnet as the proxy-server is? Brian Email Address [EMAIL PROTECTED] ___ UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html FAQ, list archives, and subscription info: http://www.groupstudy.com Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
MTU for a DSL connection
What should I set my WIN98SE MTU setting to ? When I get my DSL connection? and does anyone recommend anyone setting for MTU for Dial-up? I know there are programs out there to change it, but does someone know of a good one to change my MTU on my Win98SE or what about Windows 2000 server and Pro? ___ UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html FAQ, list archives, and subscription info: http://www.groupstudy.com Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
SOME FREE PRACTICE TESTS
http://www.thetestpage.net/tests/tests.htm Brian Email Address [EMAIL PROTECTED] ___ UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html FAQ, list archives, and subscription info: http://www.groupstudy.com Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Using Queing over the Internet
Can you setup a VPN queing between two sites? ___ UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html FAQ, list archives, and subscription info: http://www.groupstudy.com Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Check out Select a Product
http://www.cisco.com/pcgi-bin/front.x/corona/prodtool/select.pl Brian Email Address [EMAIL PROTECTED] ___ UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html FAQ, list archives, and subscription info: http://www.groupstudy.com Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
What is this magic number for a 3600 router
When I try to boot my 3620 it keep asking me " I need a magic number" the router won't boot? It keeps going into romon1 mode? Brian Email Address [EMAIL PROTECTED] ___ UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html FAQ, list archives, and subscription info: http://www.groupstudy.com Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Sharing Win95/98 to Win 2000 Pro
It does work thanks to a few, all you have to do is setup a user in Win2000 pro and make sure both machines are in the same workgroup and with the 95/98 make sure you don't have login into Domain click in network properties. Make sure both machines are on the same subnet to. Brian Email Address [EMAIL PROTECTED] ___ UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html FAQ, list archives, and subscription info: http://www.groupstudy.com Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: Setting up sharing from WIN95/98 to WIN2000 PRO
my girlfriend did, she downloaded it and it still does not work. Thanks Brian Email Address [EMAIL PROTECTED] ___ UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html FAQ, list archives, and subscription info: http://www.groupstudy.com Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Setting up sharing from WIN95/98 to WIN2000 PRO
Have a question? about setting up file and print sharing from Windows 98 SE to WIN95B to Windows 2000 pro. I gives me either a IPC$ or a permission error, but when I go from Windows 2000 to Win98Se to Win95B it works fine? I can ping both sides just fine, I have both setup as workgroups as well? PLEase HElp! is this a well problem with WIN2000? I can peer 2 win98 machines just fine the same ones that is trying to share the Windows 2000 pro machine. I have try this on many different machines. Brian Email Address [EMAIL PROTECTED] ___ UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html FAQ, list archives, and subscription info: http://www.groupstudy.com Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: CCNA jobs
How much experience do you have? how much networking have you done in the pass??? just passing your CCNA does not mean your going to land a WAN job ASAP? but you just may. are you working on your CCDA or CCNP. you should know more just then Cisco products, learn what other types of layer 3 products are on the market as well. Brian Email Address [EMAIL PROTECTED] ___ UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html FAQ, list archives, and subscription info: http://www.groupstudy.com Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Accesslist/ syslog question?
I have my Syslog Deamon running and I have been noticing this 224.0.0.10 address coming up every once in a while? I know it's not a Class A, B or C address , It's a Class D address. What is it doing here? 41: *Mar 1 00:27:16: %SEC-6-IPACCESSLOGNP: list routerBin permitted 88 192.1.1.1 - 224.0.0.10, 65 packets Brian Email Address [EMAIL PROTECTED] ___ UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html FAQ, list archives, and subscription info: http://www.groupstudy.com Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: VPNS/access-list question
this worked access-list 105 permit tcp any host X.X.X.X eq 1723 access-list 105 permit gre any host X.X.X.X access-list 105 permit 50 any host X.X.X.X access-list 105 permit tcp any any established access-list 105 permit icmp any any access-list 105 deny udp any any eq 135 access-list 105 deny udp any any eq 136 access-list 105 deny udp any any eq 137 access-list 105 deny udp any any eq 138 access-list 105 deny udp any any eq 139 access-list 105 permit udp any any Interface Ethernet0 ip address X.X.X.X 255.255.255.0 access-group 105 out I was able not to login into the 2000Server, but after I established a VPN to the Server it worked. I was able to get login into the server. This seem only to work with 98SE and 2000 PRO, I have trouble with 95B for some reason??? I did upgrade to DUN 1.3. Is their anything else I should watch out for. THANKS... Brian Email Address [EMAIL PROTECTED] ___ UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html FAQ, list archives, and subscription info: http://www.groupstudy.com Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Looping a Cisco router
Hi Can someone help me here, on a Cisco router with any type of WIC what is the Cisco command to do a loopback at the router? it's 'loop ' can someone please help? Brian Email Address [EMAIL PROTECTED] ___ UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html FAQ, list archives, and subscription info: http://www.groupstudy.com Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Loopbacking the Router?
just to let you know that you can set a loopback on a Cisco router from the router ? You must be in the priv mode not user mode to put the router in loopback. Router# Router#conf ter ( hit enter ) Router(config)#int s0 ( hit enter ) Router(config-if)#LOOPBACK (hit enter ) Router(config-if)#end (hit enter ) Router#sho int s0 ( you will now see the serial interface in loopback) To remove the loopback from the serial interface just reload the router or do this: Router# Router#conf ter ( hit enter ) Router(config)#int s0 ( hit enter ) Router(config-if)#NO LOOPBACK (hit enter ) Router(config-if)#end (hit enter ) Router#sho int s0 ( you will now see the serial interface out of the loopback) Brian Email Address [EMAIL PROTECTED] ___ UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html FAQ, list archives, and subscription info: http://www.groupstudy.com Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: Modem/Console port logon problem
Make sure you have set 9600 8-N-1 on you program or you will not get in and make sure you are using the right Cisco cable and hard shell connector . If you are still having problems try another computer their might be something wrong with the com port on that machine.. Brian ___ UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html FAQ, list archives, and subscription info: http://www.groupstudy.com Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: MAC Address
http://memphis.supersharewareman.com/Apps/2449.asp Check this out ___ UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html FAQ, list archives, and subscription info: http://www.groupstudy.com Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: access list editing
I would MAKE SURE you remove the IP access group XX on your interfaces before you paste your access lists back first. ___ UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html FAQ, list archives, and subscription info: http://www.groupstudy.com Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: access list editing
I would check the systax against the router to make sure you are using the right commands? , I use the ? make after each command to make sure I am doing it right. ___ UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html FAQ, list archives, and subscription info: http://www.groupstudy.com Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: BCRAN Tips
I would read the BCRAN book from Mc Graw Hill ISBN 00721244806 it's GREAT, it tells you alot of good things about the test and plus you will learn so much more. Brian Email Address [EMAIL PROTECTED] ___ UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html FAQ, list archives, and subscription info: http://www.groupstudy.com Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
What is a daemon ?
The term daemon means the process is running "in the background," carrying out operations on behalf of the whole system. Daemons are normally started when the system is bootstrapped and run as long as the system is up. Brian Email Address [EMAIL PROTECTED] ___ UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html FAQ, list archives, and subscription info: http://www.groupstudy.com Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
What is Keepalives???
Does anyone have a short good definition of what a keepalive is Brian Email Address [EMAIL PROTECTED] ___ UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html FAQ, list archives, and subscription info: http://www.groupstudy.com Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Setting up a Cisco VPN 17XX Router
Hello, I have a Cisco 1750 router here at the office and want to be able to setup VPN services from the Internet comining into my Cisco 1750 router, does anyone have a sample config of one. I am having my user going to start using VPN over then just dialing into the RAS box to cut down long distance calling into the office. I haved looked on the WEB for sample config's but there not that I could find? I even looked ont the Cisco site nothing. Thank Brian Email Address [EMAIL PROTECTED] ___ UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html FAQ, list archives, and subscription info: http://www.groupstudy.com Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: whats a nibble?
Thats a salior for you, my nibble are big chested women well you all guy know the rest...LOL Brian Email Address [EMAIL PROTECTED] ___ UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html FAQ, list archives, and subscription info: http://www.groupstudy.com Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: LINUX ROUTER ,,HELP
thanks one question not a greu at Linux yet, what command should I execute to get to the 'echo 1' prompt I did this once. what group were you from the Cisco or Redhat group Thanks again Brian Email Address [EMAIL PROTECTED] ___ UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html FAQ, list archives, and subscription info: http://www.groupstudy.com Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: How to enable the telnet on NT Box
Windows 2000 both Server and Prof come with telnet servers, there are free ones on the web. Brian Email Address [EMAIL PROTECTED] ___ UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html FAQ, list archives, and subscription info: http://www.groupstudy.com Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]