invalid
hi: all,i have a router 2620 prompt the information below: cisco 2620 (MPC860) processor (revision 0x102) with 28672K/4096K bytes of memory. Processor board ID JAD04310EXU (2782278826) M860 processor: part number 0, mask 49 Bridging software. X.25 software, Version 3.0.0. Basic Rate ISDN software, Version 1.1. 1 FastEthernet/IEEE 802.3 interface(s) 4 Low-speed serial(sync/async) network interface(s) 1 ISDN Basic Rate interface(s) 32K bytes of non-volatile configuration memory. 8192K bytes of processor board System flash (Read/Write) Invalid percentage: valid values are:10, 15, 20, 25, 30, 40, 50 what's the problem in this router thanks tom _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: invalid
it sounds to me that someone has tried to change the proportion of dram allocated to main memory versus io memory this is a cut and paste from a cisco web doc at http://www.cisco.com/univercd/cc/td/doc/product/software/ios120/12cgcr/fun_c /fcprt2/fcmemory.htm Valid I/O memory percentage values are 10, 15, 20, 25, 30, 40 (the default), and 50. I/O memory size is the specified percentage of total memory size, rounded down to the nearest multiple of 1 MB. A minimum of 4 MB of memory is required for I/O memory. The remaining memory is processor memory. dave h -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]] Sent: Tuesday, January 02, 2001 9:42 PM To: [EMAIL PROTECTED] Subject: invalid hi: all,i have a router 2620 prompt the information below: cisco 2620 (MPC860) processor (revision 0x102) with 28672K/4096K bytes of memory. Processor board ID JAD04310EXU (2782278826) M860 processor: part number 0, mask 49 Bridging software. X.25 software, Version 3.0.0. Basic Rate ISDN software, Version 1.1. 1 FastEthernet/IEEE 802.3 interface(s) 4 Low-speed serial(sync/async) network interface(s) 1 ISDN Basic Rate interface(s) 32K bytes of non-volatile configuration memory. 8192K bytes of processor board System flash (Read/Write) Invalid percentage: valid values are:10, 15, 20, 25, 30, 40, 50 what's the problem in this router thanks tom _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
invalid checksum [7:63112]
Hi, I have a 4000-M router that I installed 2 4Meg flash modules in and I partitioned them to look like its an 8 Meg module. I loaded an ios image on it. Everything looks ok and it works fine until I power off the router. After I power down the router and than start it back up it boots in to the router prompt. On doing a show flash I see an invalid checksum. Is it because I am using 2 4 Meg flash modules. I know if I use a single 8 Meg module it works fine but I am just trying to put my 4 meg modules to good use. After I tftp another image it works fine until I power off the router and than again its the same thing. I would appreciate any help. Please let me know. Thanks. Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=63112&t=63112 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Invalid EOC address [7:40578]
Hello, how to disable the embedded operation channel (EOC) on Cisco 828 (g.SHDSL Router)? The router floods the message "Invalid EOC address" to the console. Best regards, Stefan Reelsen -- Stefan Reelsen celox Telekommunikationsdienste GmbH phone: +49 228 93192-28 fax: -90 Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=40578&t=40578 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Invalid IOS Image [7:14105]
When I look up the image I currently have on one of my 2501's, it says "c2500-d-l.113-11a.bin". However, if I try to find it in the Cisco IOS Feature Navigator, it tells me that it's an invalid image. What's wrong - has someone saved the flash under a different name, and if so, would the "show ver" show the wrong filename or the actual version encoded in the image? - Or, does this navigator not find all versions??? Thanks, Ole Ole Drews Jensen Systems Network Manager CCNA, MCSE, MCP+I RWR Enterprises, Inc. [EMAIL PROTECTED] http://www.RouterChief.com NEED A JOB ??? http://www.oledrews.com/job Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=14105&t=14105 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
invalid config reg [7:32673]
hi all, does anyone know how to recover from an invalid config-reg value that was entered on the rommon prompt of a 3660 __ Do You Yahoo!? Send FREE video emails in Yahoo! Mail! http://promo.yahoo.com/videomail/ Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=32673&t=32673 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: invalid checksum [7:63112]
Could someone please help me out with this. Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=63545&t=63112 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: invalid checksum [7:63112]
Vic, One of your 4Mb Flash Modules might be bad, did you try using them alone? I had the same problem on a 2600, but with 2x8Mb Flash config. What I did was: using a third 8Mb Flash Module, replaced one module at a time, reload the IOS, reload the router until it worked. If you can't try that, try using your 4 Mb Flash modules with an IOS that would fit in 4 Mb and test them separately. Regards, Jose ""Vic Dmon"" escribis en el mensaje news:[EMAIL PROTECTED] > Could someone please help me out with this. Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=63556&t=63112 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Invalid Object Identifier [7:43093]
Hi All, Please kindly assist in resolving this, One of the router am managing log the following errors which I pasted below. Can anyone suggest the best way to resolve this problem. *Apr 29 00:49:28: %OSPF-5-ADJCHG: Process 1, Nbr 10.6.100.254 on Serial3/1/3 from FULL to DOWN, Neighbor Down: Dead timer expired *Apr 29 00:49:52: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial3/1/3, changed state to down *Apr 29 00:51:15: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial3/1/3, changed state to up *Apr 29 00:51:24: %OSPF-5-ADJCHG: Process 1, Nbr 10.6.100.254 on Serial3/1/3 from LOADING to FULL, Loading Done *Apr 29 01:06:19: %SNMP-3-BADOID: Attempt to generate an invalid object identifier -Traceback= 607BA288 607BA0E0 607B9EAC 607C53C0 607C52E8 607D84C4 604B3A10 60313B74 60313B60 *Apr 29 01:07:57: %SNMP-3-BADOID: Attempt to generate an invalid object identifier -Traceback= 607BA288 607BA0E0 607B9EAC 607C53C0 607C52E8 607D84C4 604B3A10 60313B74 60313B60 *Apr 29 01:09:05: %SNMP-3-BADOID: Attempt to generate an invalid object identifier -Traceback= 607BA288 607BA0E0 607B9EAC 607C53C0 607C52E8 607D84C4 604B3A10 60313B74 60313B60 *Apr 29 01:10:01: %SNMP-3-BADOID: Attempt to generate an invalid object identifier -Traceback= 607BA288 607BA0E0 607B9EAC 607C53C0 607C52E8 607D84C4 604B3A10 60313B74 60313B60 *Apr 29 01:10:45: %SNMP-3-BADOID: Attempt to generate an invalid object identifier -Traceback= 607BA288 607BA0E0 607B9EAC 607C53C0 607C52E8 607D84C4 604B3A10 60313B74 60313B60 *Apr 29 01:11:56: %SNMP-3-BADOID: Attempt to generate an invalid object identifier -Traceback= 607BA288 607BA0E0 607B9EAC 607C53C0 607C52E8 607D84C4 604B3A10 60313B74 60313B60 *Apr 29 01:12:48: %SNMP-3-BADOID: Attempt to generate an invalid object identifier -Traceback= 607BA288 607BA0E0 607B9EAC 607C53C0 607C52E8 607D84C4 604B3A10 60313B74 60313B60 *Apr 29 03:28:02: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/1/1, changed state to up *Apr 29 03:28:11: %OSPF-5-ADJCHG: Process 1, Nbr 10.11.2.1 on Serial1/1/1 from LOADING to FULL, Loading Done *Apr 29 04:06:44: %SNMP-3-BADOID: Attempt to generate an invalid object identifier -Traceback= 607BA288 607BA0E0 607B9EAC 607C53C0 607C52E8 607D84C4 604B3A10 60313B74 60313B60 *Apr 29 04:06:44: %SNMP-3-BADOID: Attempt to generate an invalid object identifier -Traceback= 607BA288 607BA0E0 607B9EAC 607C53C0 607C52E8 607D84C4 604B3A10 60313B74 60313B60 *Apr 29 04:06:44: %SNMP-3-BADOID: Attempt to generate an invalid object identifier -Traceback= 607BA288 607BA0E0 607B9EAC 607C53C0 607C52E8 607D84C4 604B3A10 60313B74 60313B60 *Apr 29 04:06:50: %SNMP-3-BADOID: Attempt to generate an invalid object identifier -Traceback= 607BA288 607BA0E0 607B9EAC 607C53C0 607C52E8 607D84C4 604B3A10 60313B74 60313B60 *Apr 29 04:06:50: %SNMP-3-BADOID: Attempt to generate an invalid object identifier -Traceback= 607BA288 607BA0E0 607B9EAC 607C53C0 607C52E8 607D84C4 604B3A10 60313B74 60313B60 *Apr 29 04:06:50: %SNMP-3-BADOID: Attempt to generate an invalid object identifier -Traceback= 607BA288 607BA0E0 607B9EAC 607C53C0 607C52E8 607D84C4 604B3A10 60313B74 60313B60 Regards, BBji = Regards, Banji (MCSE,CCNP). Snr. Technical Trainer. USG Technology Ltd. 15/17 Opebi Road. Ikeja, Lagos. Tel: 234-01-4932401-6 ICQ #: 75533196 __ Do You Yahoo!? Yahoo! Health - your guide to health and wellness http://health.yahoo.com Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=43093&t=43093 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: invalid config reg [7:32673]
Follow the first part of the password recovery procedure to set it back to 2102 see: http://www.cisco.com/warp/public/474/pswdrec_3600.shtml Taco. -Original Message- From: Amii Papa [mailto:[EMAIL PROTECTED]] Sent: Monday, January 21, 2002 10:59 AM To: [EMAIL PROTECTED] Subject: invalid config reg [7:32673] hi all, does anyone know how to recover from an invalid config-reg value that was entered on the rommon prompt of a 3660 __ Do You Yahoo!? Send FREE video emails in Yahoo! Mail! http://promo.yahoo.com/videomail/ Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=32674&t=32673 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: invalid config reg [7:32673]
Thanks for your prompt help. The thing is that the router's conf-reg setting was previously 0x3920. This was to allow faster xmodem speeds. In resetting back to 0x2102, a totally invalid number was entered. As a result one is not able to see anything on hyperterminal anymore. --- Taco Hettema wrote: > Follow the first part of the password recovery > procedure to set it back to 2102 > > see: > http://www.cisco.com/warp/public/474/pswdrec_3600.shtml > > Taco. > > -Original Message- > From: Amii Papa [mailto:[EMAIL PROTECTED]] > Sent: Monday, January 21, 2002 10:59 AM > To: [EMAIL PROTECTED] > Subject: invalid config reg [7:32673] > > > hi all, > does anyone know how to recover from an invalid > config-reg value that was entered on the rommon > prompt > of a 3660 > > > > __ > Do You Yahoo!? > Send FREE video emails in Yahoo! Mail! > http://promo.yahoo.com/videomail/ [EMAIL PROTECTED] __ Do You Yahoo!? Send FREE video emails in Yahoo! Mail! http://promo.yahoo.com/videomail/ Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=32678&t=32673 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: invalid config reg [7:32673]
set the hyperterm speed to 9600 then. ""Amii Papa"" wrote in message [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... > Thanks for your prompt help. > > The thing is that the router's conf-reg setting was > previously 0x3920. This was to allow faster xmodem > speeds. In resetting back to 0x2102, a totally invalid > number was entered. > > As a result one is not able to see anything on > hyperterminal anymore. > --- Taco Hettema wrote: > > Follow the first part of the password recovery > > procedure to set it back to 2102 > > > > see: > > > http://www.cisco.com/warp/public/474/pswdrec_3600.shtml > > > > Taco. > > > > -Original Message- > > From: Amii Papa [mailto:[EMAIL PROTECTED]] > > Sent: Monday, January 21, 2002 10:59 AM > > To: [EMAIL PROTECTED] > > Subject: invalid config reg [7:32673] > > > > > > hi all, > > does anyone know how to recover from an invalid > > config-reg value that was entered on the rommon > > prompt > > of a 3660 > > > > > > > > __ > > Do You Yahoo!? > > Send FREE video emails in Yahoo! Mail! > > http://promo.yahoo.com/videomail/ > [EMAIL PROTECTED] > > > __ > Do You Yahoo!? > Send FREE video emails in Yahoo! Mail! > http://promo.yahoo.com/videomail/ Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=32761&t=32673 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: invalid config reg [7:32673]
jumpers in the router can be set so that console speed goes default to 9600. just follow this link http://www.cisco.com/warp/public/701/59.html#conspeed regards jagan Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=32779&t=32673 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
ISDN- Invalid number format or Special Intercept
Hi! at the moment i am simulating isdn-circuits with two cisco 2600 and an isdn-pbx. the router is dialing - i get back a SETUP_ACK but get disconnected some time later. Cause: DISCONNECT Cause i = 0x819C - Invald Number format or Special Intercept ? All interfaces are up ! Layer 1 Status: ACTIVE Layer 2 Status: TEI=64, Ces = 1 SAPI = 0 , State = Multiple_Frame_Esablished Layer 3 Status : 0 Active Calls Did i configure the PBX incorrectely ? do i need ISDN SPIDs for isdn-switch type basic-ni ? i would appriciate any help ! thanx in advance hans **NOTE: New CCNA/CCDA List has been formed. For more information go to http://www.groupstudy.com/list/Associates.html _ UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html FAQ, list archives, and subscription info: http://www.groupstudy.com Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
invalid magic number in 2600 [7:21249]
I can't boot a 2600 router, I get the message 'invalid magic number' in flash. Ive tried changing the config register but it didn't work. Please if you know how to fix this answer to [EMAIL PROTECTED] please (if you want to answer to the newsgroup you can too, but please i prefer the email response). Thanks in advance. I have some other question to ask. Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=21249&t=21249 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: invalid magic number in 2600 [7:21249]
Similar problem here when using new FLASH which is not "formatted". Try this, go to ROMMON and do the TFTP download from ROMMON. After reboot should solve the problem. Good luck. Ryan -Original Message- From: Alejandro Pelaez [mailto:[EMAIL PROTECTED]] Sent: Thursday, September 27, 2001 12:42 PM To: [EMAIL PROTECTED] Subject: invalid magic number in 2600 [7:21249] I can't boot a 2600 router, I get the message 'invalid magic number' in flash. Ive tried changing the config register but it didn't work. Please if you know how to fix this answer to [EMAIL PROTECTED] please (if you want to answer to the newsgroup you can too, but please i prefer the email response). Thanks in advance. I have some other question to ask. Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=21252&t=21249 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: invalid magic number in 2600 [7:21249]
try to erase flash and put the ios again send the dump of yr screen -Original Message- From: Alejandro Pelaez [mailto:[EMAIL PROTECTED]] Sent: Thursday, September 27, 2001 8:42 AM To: [EMAIL PROTECTED] Subject: invalid magic number in 2600 [7:21249] I can't boot a 2600 router, I get the message 'invalid magic number' in flash. Ive tried changing the config register but it didn't work. Please if you know how to fix this answer to [EMAIL PROTECTED] please (if you want to answer to the newsgroup you can too, but please i prefer the email response). Thanks in advance. I have some other question to ask. Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=21255&t=21249 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Operation Firmware is invalid? Please help...Urgent [7:44673]
Cisco ws-c1900 switch. Using db9F-rollover-db9F or null modem cable I can connect to the console port and get into Diag Console fine, but when I try to just plug in and configure the switch it just starts spitting out "ATQ0H0" in hyperterminal PE. I hunted around and a couple places that I found said try updating the firmware. So I hit cisco's site and downloaded "cat1900A.9.00.04.bin" which was the only 1900 firmware I could find, The previous version was 5.34. So anyway, I did the XModem firmware upgrade, as soon as it asks me to send the file it kicks back an error that says "Transfer cancelled by remote system" (convenietly after it has erased existing firmware) and then prints out: Operation firmware version: 0.00Status: Invalid Boot firmware version: 1.10 WARNING!!! Operation Firmware is invalid. Upgrade firmware to enable switch operation. Im stuck at this point, does anyone know what to do or how to get a copy of the firmware that works on this switch? and then at that point what kind of cables, etc do i need to configure the darn thing. If anyone can get back to me in a hurry or has a version of the firmware that DOES work on this model it would be greatly apprecieated as this switch is dead in the water, along with the LAN that is suppost to be connected to it. Thanks, Justin Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=44673&t=44673 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: Operation Firmware is invalid? Please help...Urgent [7:44711]
Your problem is spooky, I just had the exact same problem with a 1924 the other day. Same symptoms, same inability to use XMODEM to upgrade the flash. I discovered that not all null modem cables are made the same, strangely enough. Do a search on CCO and you will find a variety of pinouts. I finally found a null modem cable with the same pinout that is specified in the 1900 documentation for release 5.x: http://www.cisco.com/univercd/cc/td/doc/product/lan/28201900/1928v5x/icg5x/c sspec.htm When I use the correct(!) null modem it cable it works fine. Sincerely, John Dorffler CCIE #6677 ""Justin M. Clark"" wrote in message [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... > Cisco ws-c1900 switch. Using db9F-rollover-db9F or null modem cable I can > connect to the console port and get into Diag Console fine, but when I try > to just plug in and configure the switch it just starts spitting out > "ATQ0H0" in hyperterminal PE. I hunted around and a couple places that I > found said try updating the firmware. So I hit cisco's site and downloaded > "cat1900A.9.00.04.bin" which was the only 1900 firmware I could find, The > previous version was 5.34. So anyway, I did the XModem firmware upgrade, as > soon as it asks me to send the file it kicks back an error that says > "Transfer cancelled by remote system" (convenietly after it has erased > existing firmware) and then prints out: > Operation firmware version: 0.00Status: Invalid > Boot firmware version: 1.10 > WARNING!!! Operation Firmware is invalid. > Upgrade firmware to enable switch operation. > > Im stuck at this point, does anyone know what to do or how to get a copy of > the firmware that works on this switch? and then at that point what kind of > cables, etc do i need to configure the darn thing. > > If anyone can get back to me in a hurry or has a version of the firmware > that DOES work on this model it would be greatly apprecieated as this switch > is dead in the water, along with the LAN that is suppost to be connected to > it. > > Thanks, > Justin Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=44711&t=44711 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: Operation Firmware is invalid? Please help...Urgent [7:44719]
Two other things. This is only a problem (as far as I know) on the older 1900s with the DB-9 console port. The other issue, and I have sorta confirmed it, is that you can't load anything older than about 5.37 on the older 1900s. I was able to do that with my old 1924, but it gags when I try to upload 9.0. If anybody has any additional info on the limitations of the older 1900s, please post because I can't find anything more on CCO. Sincerely, John Dorffler CCIE #6677 ""Justin M. Clark"" wrote in message [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... > Cisco ws-c1900 switch. Using db9F-rollover-db9F or null modem cable I can > connect to the console port and get into Diag Console fine, but when I try > to just plug in and configure the switch it just starts spitting out > "ATQ0H0" in hyperterminal PE. I hunted around and a couple places that I > found said try updating the firmware. So I hit cisco's site and downloaded > "cat1900A.9.00.04.bin" which was the only 1900 firmware I could find, The > previous version was 5.34. So anyway, I did the XModem firmware upgrade, as > soon as it asks me to send the file it kicks back an error that says > "Transfer cancelled by remote system" (convenietly after it has erased > existing firmware) and then prints out: > Operation firmware version: 0.00Status: Invalid > Boot firmware version: 1.10 > WARNING!!! Operation Firmware is invalid. > Upgrade firmware to enable switch operation. > > Im stuck at this point, does anyone know what to do or how to get a copy of > the firmware that works on this switch? and then at that point what kind of > cables, etc do i need to configure the darn thing. > > If anyone can get back to me in a hurry or has a version of the firmware > that DOES work on this model it would be greatly apprecieated as this switch > is dead in the water, along with the LAN that is suppost to be connected to > it. > > Thanks, > Justin Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=44719&t=44719 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
ISDN to VOIP:Cause i = 0x809C - Invalid number format [7:48896]
I have a cisco 2621 gateway voip/isdn, the gateway has fastethernet interfaces to the lan/voip network and a 2vic BRI S/T TE connected to a ISDN BRI. Calls from a voip terminal to the pstn are OK. Calls from pstn to a voip terminals are KO. It seems I have no chance to digit the post-selection associated to the voip terminal (the same voip architecture with analog line and FXO works fine) I receive ISDN BRI1/0 TX -> DISCONNECT pd = 8 callref = 0xC7 Cause i = 0x809C - Invalid number format (incomplete number) I'm sending the configuration, any suggestion will be appreciate. Teresa isdn switch-type basic-net3 ! interface BRI1/0 no ip address isdn switch-type basic-net3 isdn overlap-receiving T302 5000 isdn not-end-to-end 64 isdn incoming-voice voice isdn send-alerting isdn sending-complete isdn skipsend-idverify Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=48896&t=48896 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
