Re: [Flexradio] Garbled output

[Paul Delaney - K6HR]

Hi Dave,

Any chance you're using a HEIL mic adapter?

I had garbled audio from RF getting into the mic connector. As it turned out
the mic was wired as 'Yaesu', but required the chassis ground pin to be
connected to the mic ground pin on the adapter. I soldered a tiny jumper
between the two pins and the problem was completely eliminated. YMMV.

Paul Delaney - K6HR
paul.hamra...@verizon.net
http://gw.k6hr.ampr.org:8080 

> -Original Message-
> From: FlexRadio [mailto:flexradio-boun...@flex-radio.biz] On Behalf Of
> Dave Gomberg
> Sent: Sunday, July 20, 2014 08:47
> To: flexradio@flex-radio.biz
> Subject: Re: [Flexradio] Garbled output
> 
> Ooops, I lied.   This morning the problem is back just the way it
> was, maybe a bit worse.
> 
> But I am pretty convinced after yesterday it is software.   Any clues?
> 
> At 17:52 7/19/2014, geo...@gloria.us wrote:
> >Power down to about one watt after rebooting the computer and
> >restarting PSDR.  Power down the radio too.  If the problem is
> >reduced or eliminated, you have RF getting into the computer.



___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
To opt out of the Reflector:
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz

Re: [Flexradio] FlexRadio Digest, Vol 109, Issue 10

[Paul Delaney - K6HR]

> -Original Message-
> From: FlexRadio [mailto:flexradio-boun...@flex-radio.biz] On Behalf Of
> Hunter Ellington
> Sent: Sunday, May 11, 2014 13:02
> To: flexradio@flex-radio.biz
> Subject: Re: [Flexradio] FlexRadio Digest, Vol 109, Issue 10
> 
> Maybe it's the snow coming down hard on May 11, or the lack of sunspot
> activity today, but this entire transition from the 5000A radios to the
> 6000 series has left a bad taste in my mouth.

Huh? Please explain.

> The sudden cessation of the
> 5000A production due to a cabinet vendor (which never did sound right),

Didn't "sound right"? What did it sound like?

> and now the introduction of the 6300 at the old 5000A's price point, it
> makes me wonder how long there will be support for PowerSDR which drives
> these older radios.  

Why would one have anything to do with the other? Please explain.

> Will the program be released as domain ware when
> support and development cease?  What happens when some critical chip for
> the 6300 series is no longer available, and there is not a readily
> available substitute?  

How would this be different than any other legacy hardware issue in the
world?

> I've had my 5000A for four years now, and it has
> been a fine radio, however, I doubt I'll be willing to part with the price
> of the 6000 series given my experience.

What was your experience?

> And yes, I know that the typical
> life cycle for the rice boxes is about four years or so, but I bought this
> radio based on the advertising hook that the Flex radios would continue to
> be expandable and evolving going forward.  

Exactly who told you they wouldn't be?

> Oh well, enough of my rant.  Anyone want a Flex
> 5000A, base model with the TI chip firewire card, cable, and FlexControl
> knob for $1925 delivered?

Seriously? Oh, forget about all the questions, I didn't realize this was a
rant.




___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
To opt out of the Reflector:
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz

Re: [Flexradio] Digital Setup

[Paul Delaney - K6HR]

 
Check the Flex Knowledge Base. Everything you need to get setup again is there.


Paul Delaney - K6HR 
http://k6hr.dyndns.org:8080

On 01/02/14, Don Plunkett wrote:

I feel very bad about sending out this email . I have lost all of the
digital setup and user information that I used to have on my computer a
radio (about 9 months ago) and would like to restart. Is there one place
that I can go to get all of the information that now works in the current
environment. I use a Flex 3000 with the current OS . Sorry guys, just want
to get back into the digital side of things.



Don

VA6FH

___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/ Homepage: http://www.flexradio.com/

___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

Re: [Flexradio] Using a 2nd Independent Receiver with the Flex 5000A

[Paul Delaney - K6HR]

It was years ago, but I do remember it was a variation on one of the
examples shown in the instruction sheet. Worked like a charm.

Paul Delaney - K6HR
paul.hamra...@verizon.net
http://k6hr.dyndns.org:8080 

> -Original Message-
> From: Mark Lunday [mailto:wd4...@triad.rr.com]
> Sent: Tuesday, September 03, 2013 14:09
> To: 'Paul'; 'Gary Smith'; flexradio@flex-radio.biz
> Subject: RE: [Flexradio] Using a 2nd Independent Receiver with the Flex
> 5000A
> 
> Paul, I have one of those RTR-1 units but I use it for two antennas and a
> single receiver/rig.  How do you set it up for two radios and one
> receiver?
> You have my curiosity piqued (sp?)
> 
> Mark Lunday, WD4ELG
> Greensboro, NC  FM06be
> wd4...@arrl.net
> http://wd4elg.blogspot.com


___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

Re: [Flexradio] 4th decimal digit readout onpanadapter/waterfallreally necessary?

[Paul Delaney - K6HR]

While we on this subject I'm wondering if it's just me or has the frequency
shown along the top of the panadapter changed to add a ".0" e.g. 14.215.0

I didn't notice this before v2.6.4 and have looked for a way to turn off the
.0 but don't find anything.

I thought it read: 14.215 previously

Paul Delaney - K6HR
paul.hamra...@verizon.net
http://k6hr.dyndns.org:8080 



> -Original Message-
> From: FlexRadio [mailto:flexradio-boun...@flex-radio.biz] On Behalf Of Ken
> Buser
> Sent: Friday, April 19, 2013 15:31
> To: Ray, K9DUR; py...@terra.com.br; flexradio@flex-radio.biz
> Subject: Re: [Flexradio] 4th decimal digit readout
> onpanadapter/waterfallreally necessary?
> 
> Rolf,
> 
> The last 3 digits can be made smaller than the first 3 digits and  they
> can
> also be made
> a color of choice...   This should help your visual identification
> 
> Go to Setup Tab, Appearance,   VFO Selections
> I am looking at PowerSDR  2.3.5
> 
> Ken   W9IE
> 
>  5:06 PM
> Subject: Re: [Flexradio] 4th decimal digit readout onpanadapter/waterfall
> really necessary?
> 
> 
> > Rolf,
> >
> > PowerSDR has always shown 6 digits after the decimal point, 3 the same
> > size as the digits to the left of the decimal point & 3 slightly
> smaller.
> > This has not changed with v2.6.4.
> >
> > 73, Ray, K9DUR
> > http://k9dur.info
> >
> > -Original Message-
> > From: FlexRadio [mailto:flexradio-boun...@flex-radio.biz] On Behalf Of
> > py...@terra.com.br
> > Sent: Friday, April 19, 2013 5:12 PM
> > To: flexradio@flex-radio.biz
> > Subject: [Flexradio] 4th decimal digit readout on panadapter/waterfall
> > really necessary?
> >
> > I notice 2.6.4 now shows the frequencies with four digits after the
> > decimal point.
> > I don´t know if that helps or not, but I personally find it confusing.
> > E.g. 50.0150 now could be missread as 50.150 if one is not carefull.
> > Wonder what others think? Maybe it could be made user-selectable?
> > Thanks for fixing that memory form bug (DE1043). That really helped!
> > 73 Rolf PY1RO
> > ___
> > FlexRadio Systems Mailing List
> > FlexRadio@flex-radio.biz
> > http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
> > Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
> > Knowledge Base: http://kc.flexradio.com/  Homepage:
> > http://www.flexradio.com/
> >
> >
> > ___
> > FlexRadio Systems Mailing List
> > FlexRadio@flex-radio.biz
> > http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
> > Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
> > Knowledge Base: http://kc.flexradio.com/  Homepage:
> > http://www.flexradio.com/
> >
> 
> 
> ___
> FlexRadio Systems Mailing List
> FlexRadio@flex-radio.biz
> http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
> Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
> Knowledge Base: http://kc.flexradio.com/  Homepage:
> http://www.flexradio.com/


___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

Re: [Flexradio] TOO DAMNED MUCH

[Paul Delaney - K6HR]

This thread should be a real pip on your digest feed!
Maybe you should consider dropping the digest version if you're not happy
with it.

Paul Delaney - K6HR
paul.hamra...@verizon.net
http://k6hr.dyndns.org:8080 

> -Original Message-
> From: FlexRadio [mailto:flexradio-boun...@flex-radio.biz] On Behalf Of
> Robert Logan
> Sent: Friday, February 22, 2013 07:41
> To: Bill Marvin
> Cc: ; Rod Lane
> Subject: Re: [Flexradio] TOO DAMNED MUCH
> 
> I second that.
> 
> Sent from my iPhone
> 
> On Feb 22, 2013, at 9:00 AM, "Bill Marvin"  wrote:
> 
> Please, stop whining.
> 
> Bill - W1LLY
> 
> 
> -Original Message-
> From: FlexRadio [mailto:flexradio-boun...@flex-radio.biz] On Behalf Of Rod
> Lane
> Sent: Friday, February 22, 2013 1:32 AM
> To: flexradio@flex-radio.biz
> Subject: [Flexradio] TOO DAMNED MUCH
> 
> I really like this reflector, and I get a lot of good information here.
> I'm
> a 3000 owner and this group has really enhanced my experience with the
> radio
> 
> 
> 
> But,  I get this list in digest mode.
> 
> 
> 
> That means if you're getting a digest feed and don't clip the reply text
> from your message, I end up getting HUNDREDS of lines of text in the
> message
> then it gets almost impossible to find the message I want out of the pile
> of
> old stuff that's included in seemingly EVERY digest pack.
> 
> 
> 
> PLEASE don't be so lazy that you can't trim your replies.  It makes it
> almost impossible to read on a Smartphone and the messages themselves end
> up
> being over 1 MB each.
> 
> 
> 
> Thanks
> 
> 
> 
> Rod Lane, N1FNE
> 
> 
> 
> ___
> FlexRadio Systems Mailing List
> FlexRadio@flex-radio.biz
> http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
> Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
> Knowledge Base: http://kc.flexradio.com/  Homepage:
> http://www.flexradio.com/
> 
> 
> -
> No virus found in this message.
> Checked by AVG - www.avg.com
> Version: 2013.0.2899 / Virus Database: 2639/6122 - Release Date: 02/21/13
> 
> -
> No virus found in this message.
> Checked by AVG - www.avg.com
> Version: 2013.0.2899 / Virus Database: 2639/6122 - Release Date: 02/21/13
> 
> 
> ___
> FlexRadio Systems Mailing List
> FlexRadio@flex-radio.biz
> http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
> Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
> Knowledge Base: http://kc.flexradio.com/  Homepage:
> http://www.flexradio.com/
> 
> ___
> FlexRadio Systems Mailing List
> FlexRadio@flex-radio.biz
> http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
> Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
> Knowledge Base: http://kc.flexradio.com/  Homepage:
> http://www.flexradio.com/


___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

Re: [Flexradio] Additional preamp on 40m and 30M...

[Paul Delaney - K6HR]

I don't see that here using PSDR 2.5.3 w/5000a
What version of PSDR and radio are you using?

Paul Delaney - K6HR
paul.hamra...@verizon.net
http://k6hr.dyndns.org:8080 


> -Original Message-
> From: FlexRadio [mailto:flexradio-boun...@flex-radio.biz] On Behalf Of Ray
> percival
> Sent: Friday, January 18, 2013 11:11
> To: flexradio@flex-radio.biz
> Subject: [Flexradio] Additional preamp on 40m and 30M...
> 
> Has anyone else noticed that there is an additional preamp on 40M and 30M
> if
> you use the keyboard CTRL P command?
> 
> This is especially noticeable when you have the AGC-T set to about 60% or
> 70%.
> 
> 40 M only has 3 levels... ATTN-OFF-PRE1
> But if you use the Ctrl-P there seems to be an additional level (Pre2
> perhaps).
> 
> Strange..
> 
> Regards
> Ray
> EI3GD
> 
> 
> 
> ___
> FlexRadio Systems Mailing List
> FlexRadio@flex-radio.biz
> http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
> Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
> Knowledge Base: http://kc.flexradio.com/  Homepage:
> http://www.flexradio.com/


___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

Re: [Flexradio] Most up to date setup directions for VAC and PowerSDR?

[Paul Delaney - K6HR]

http://kc.flexradio.com/KnowledgebaseArticle50230.aspx?Keywords=vac

Paul Delaney - K6HR
paul.hamra...@verizon.net
http://k6hr.dyndns.org:8080 

> -Original Message-
> From: FlexRadio [mailto:flexradio-boun...@flex-radio.biz] On Behalf Of
> Michael
> Sent: Thursday, January 17, 2013 16:40
> To: flexradio@flex-radio.biz
> Subject: [Flexradio] Most up to date setup directions for VAC and
> PowerSDR?
> 
> I'm trying to get everything configured for my new 1500.  It's been
> about a year since I've done any work with PowerSDR and the associated
> peripheral programs so my memory is a little foggy on setup and optimum
> settings. Also it seems to me that I've seen more than one version of
> setup instructions for VAC over the years with different values and
> recommendations in each. What are the most up to date and correct setup
> instructions?
> Thanks,
> Michael, W4HIJ
> 
> ___
> FlexRadio Systems Mailing List
> FlexRadio@flex-radio.biz
> http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
> Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
> Knowledge Base: http://kc.flexradio.com/  Homepage:
> http://www.flexradio.com/


___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

Re: [Flexradio] PowerSDR Flex3000 Soundcard Calibration

[Paul Delaney - K6HR]

Yes. Go to MMSSTV > Options > Misc Tab
Tune to WWV and press the Adj button and follow the directions
You'll be straight in no time!

Paul Delaney - K6HR
paul.hamra...@verizon.net
http://k6hr.dyndns.org:8080 

> -Original Message-
> From: FlexRadio [mailto:flexradio-boun...@flex-radio.biz] On Behalf Of
> David Walker
> Sent: Friday, January 11, 2013 02:17
> To: flexradio@flex-radio.biz
> Subject: [Flexradio] PowerSDR Flex3000 Soundcard Calibration
> 
> Is it necessary to do the Soundcard Calibration process with MMTTY for
> SSTV using PowerSDR+VAC?
> 
> I've just installed and picked up some pics with slants.  I don't know
> whether its them or me.
> 
> Regards
> 
> Dave.
> 
> ___
> FlexRadio Systems Mailing List
> FlexRadio@flex-radio.biz
> http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
> Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
> Knowledge Base: http://kc.flexradio.com/  Homepage:
> http://www.flexradio.com/


___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

Re: [Flexradio] FLEX-5000 Antenna Settings for RX2

[Paul Delaney - K6HR]

Hello Gary,

Click on setup, then click the General menu tab, then click RX2 tab.
Here you will see a checkbox for "Disconnect RX2 RF Input on TX

Paul Delaney - K6HR
paul.hamra...@verizon.net
http://k6hr.dyndns.org:8080 

> -Original Message-
> From: FlexRadio [mailto:flexradio-boun...@flex-radio.biz] On Behalf Of
> Gary Smith
> Sent: Thursday, January 10, 2013 21:42
> To: FlexRadio@flex-radio.biz
> Subject: [Flexradio] FLEX-5000 Antenna Settings for RX2
> 
> I am using a FLEX-5000A with the RX2 option installed and a single antenna
> for transmit and receive. Can I enable RX2 using the RX1 Tap option
> without
> front end overload damage while transmitting? My antenna settings are as
> follows:
> 
> 
> 
> Receiver 1 = ANT1
> 
> Receiver 2 = RX1 Tap
> 
> Transmit  =  ANT 1
> 
> 
> 
> Lock is checked
> 
> 
> 
> Switch Relay with TR
> 
> TX1 TX2 TX3 all checked
> 
> 
> 
> 
> 
> Thanks for advice on this issue.
> 
> Gary WB8BFW
> 
> 
> 
> ___
> FlexRadio Systems Mailing List
> FlexRadio@flex-radio.biz
> http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
> Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
> Knowledge Base: http://kc.flexradio.com/  Homepage:
> http://www.flexradio.com/


___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

Re: [Flexradio] VAC

[Paul Delaney - K6HR]

There is also a VAC Setup how-to in the Flex knowledge base


Paul Delaney - K6HR
paul.hamra...@verizon.net
http://k6hr.dyndns.org:8080 

> -Original Message-
> From: FlexRadio [mailto:flexradio-boun...@flex-radio.biz] On Behalf Of
> jonwei...@aol.com
> Sent: Saturday, December 15, 2012 14:10
> To: flexradio@flex-radio.biz
> Subject: [Flexradio] VAC
> 
> I could use some help getting the VAC to work. I'm receiving fine through
> it, but no luck transmitting. I might need someone to talk me through some
> of  the settings (perhaps on the phone). Please reply to my email address
> _jonweiner@aol.com_ (mailto:jonwei...@aol.com)  and not through the
> reflector.
> Thanks
> 
> JON
> K1VVC
> ___
> FlexRadio Systems Mailing List
> FlexRadio@flex-radio.biz
> http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
> Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
> Knowledge Base: http://kc.flexradio.com/  Homepage:
> http://www.flexradio.com/


___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

Re: [Flexradio] VOX on Flex 5000A

[Paul Delaney - K6HR]

Same here. Unable to activate VOX from GUI or Setup Menu!

Paul Delaney - K6HR
paul.hamra...@verizon.net
http://k6hr.dyndns.org:8080 

> -Original Message-
> From: FlexRadio [mailto:flexradio-boun...@flex-radio.biz] On Behalf Of Jim
> Streible
> Sent: Tuesday, December 11, 2012 20:43
> To: flexradio@flex-radio.biz
> Subject: [Flexradio] VOX on Flex 5000A
> 
> I upgraded to v2.5.3 yesterday and everything seems to
> be working OK except I can not get the VOX to turn on.
> 
> Have I missed something? Has anyone else had this problem?
> 
> Thanks,
> 
> Jim  K4DLI



___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

Re: [Flexradio] No Audio

[Paul Delaney - K6HR]

Do you have any audio output on the headphone jack?

Paul Delaney - K6HR
paul.hamra...@verizon.net
http://k6hr.dyndns.org:8080 


> -Original Message-
> From: FlexRadio [mailto:flexradio-boun...@flex-radio.biz] On Behalf Of Dan
> Mees
> Sent: Friday, November 30, 2012 07:34
> To: flexradio@flex-radio.biz
> Subject: [Flexradio] No Audio
> 
> Boot up... turn everthing on...   all appears to be normal  ... but no
> audio .
> this happend one other time ..in the beginning... and I think I just
> turned it off shut down PSDR.  Turned everthing bck on and it was ok.
> 
> 
> thats not the case today.  hhhuummm.. !
> 73
> danno
> ___
> FlexRadio Systems Mailing List
> FlexRadio@flex-radio.biz
> http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
> Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
> Knowledge Base: http://kc.flexradio.com/  Homepage:
> http://www.flexradio.com/


___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

Re: [Flexradio] Waterfall memory for each band

[Paul Delaney - K6HR]

It would be really nifty if a future version could include discrete AF
controls for the main RX and RX2. In the current version the 'main' AF
slider affects both RX1 and RX2 would be nice to be able to listen to RX2
individually!

Paul Delaney - K6HR
paul.hamra...@verizon.net
http://k6hr.dyndns.org:8080 

> 
> You may want to wait until PowerSDR v2.5.x is released (hint)
> 
> Tim Ellison



___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

Re: [Flexradio] CTCSS Problem?

[Paul Delaney - K6HR]

Thanks Steve and Dave! That did the trick!

Paul Delaney - K6HR
paul.hamra...@verizon.net
http://k6hr.dyndns.org:8080 

> -Original Message-
> From: Steve Fowler [mailto:killmo...@gmail.com]
> Sent: Sunday, September 23, 2012 11:04
> To: Dave Beumer WØDHB
> Cc: Paul Delaney - K6HR; flexradio@flex-radio.biz
> Subject: Re: [Flexradio] CTCSS Problem?
> 
> I just checked and found that all of my VHF / UHF memories would not
> function after the upgrade.  They were there and I could select them, but
> each time I got a message about the VFO freqs being incorrect.
> 
> I only had a dozen local repeaters entered so I just used the memory
> screen to manually delete them all, which gave me a database error on each
> element in each row during the delete.
> 
> Now I can enter new memories and everything works fine again, including
> the CTCSS.
> 
> Steve
> KC0FU
> 
> 
> On Sun, Sep 23, 2012 at 12:41 PM, Dave Beumer WØDHB 
> wrote:
> 
> 
>   Paul
> 
>   Work fine here.
> 
>   Dave
> 
> 
>   -Original Message-
>   From: flexradio-boun...@flex-radio.biz
>   [mailto:flexradio-boun...@flex-radio.biz] On Behalf Of Paul Delaney
> - K6HR
>   Sent: Sunday, September 23, 2012 11:38 AM
>   To: flexradio@flex-radio.biz
>   Subject: [Flexradio] CTCSS Problem?
> 
> 
>   Anyone else having a problem with CTCSS tones not working under
> 2.4.4 ?
>   Before I press the button, will resetting the database help correct
> this?
>   I'm no longer able to open any local repeaters since upgrading to
> 2.4.4.
> 
>   Paul Delaney - K6HR
>   paul.hamra...@verizon.net
>   http://k6hr.dyndns.org:8080
> 
> 
> 
>   ___
>   FlexRadio Systems Mailing List
>   FlexRadio@flex-radio.biz
>   http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
>   Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
>   Knowledge Base: http://kc.flexradio.com/  Homepage:
>   http://www.flexradio.com/
> 
> 
>   ___
>   FlexRadio Systems Mailing List
>   FlexRadio@flex-radio.biz
>   http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
>   Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
>   Knowledge Base: http://kc.flexradio.com/  Homepage:
> http://www.flexradio.com/
> 
> 



___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

[Flexradio] CTCSS Problem?

[Paul Delaney - K6HR]

Anyone else having a problem with CTCSS tones not working under 2.4.4 ?
Before I press the button, will resetting the database help correct this?
I'm no longer able to open any local repeaters since upgrading to 2.4.4.

Paul Delaney - K6HR
paul.hamra...@verizon.net
http://k6hr.dyndns.org:8080 



___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

Re: [Flexradio] Slow Main Window Command Response in PSDR

[Paul Delaney - K6HR]

Interesting, none of that behavior seen here.

Paul Delaney - K6HR
paul.hamra...@verizon.net
http://k6hr.dyndns.org:8080 

> -Original Message-
> From: flexradio-boun...@flex-radio.biz [mailto:flexradio-bounces@flex-
> radio.biz] On Behalf Of Richard Langford KD8LCD
> Sent: Sunday, September 09, 2012 11:09
> To: wd8...@arrl.net; w4yxu@gmail.com
> Cc: flexradio@flex-radio.biz
> Subject: [Flexradio] Slow Main Window Command Response in PSDR
> 
> I have had this issue as well,
> 
> 
> 
> I have also noticed an extremely slow start up response from when you
> click
> on the power button as well, the system hangs for about 15-20 seconds then
> comes on. Once it is on there are mirrored or ghosted images displayed on
> the pan-adapter. These ghost images last for approximately a minute plus
> then go away, after which it seems to operate correctly.  With exception
> to
> the lag when sometimes clicking on a menu button.
> 
> 
> 
> System here AMD FX 8150 8 core
> 
> 
> 
> Also tried an FX 6120 6 core and AMD Phenom 3.3 all produced the same
> outcome. Also put together a test system using a different brand of mother
> board, also swapped out fire-wire controller cards as well all produced
> the
> same end result.
> 
> 
> 
> Went back to version 2.3.5
> 
> 
> 
> Rick
> 
> KD8LCD
> 
> 



___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

Re: [Flexradio] New SDR

[Paul Delaney - K6HR]

The current version is 2.3.5 so a version 4 at this time would be a real
stretch!

Paul Delaney - K6HR
paul.hamra...@verizon.net
http://k6hr.dyndns.org:8080 

> -Original Message-
> From: flexradio-boun...@flex-radio.biz [mailto:flexradio-bounces@flex-
> radio.biz] On Behalf Of Ronald Arrowood
> Sent: Saturday, September 01, 2012 10:32
> To: flexradio@flex-radio.biz
> Subject: [Flexradio] New SDR
> 
> Just came from the Shelby Hamfest, saw a 3000 running I believe new SDR
> Software, version 4? Could not get close enough to see too good.
> 
> 
> ___
> FlexRadio Systems Mailing List
> FlexRadio@flex-radio.biz
> http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
> Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
> Knowledge Base: http://kc.flexradio.com/  Homepage:
> http://www.flexradio.com/


___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

Re: [Flexradio] fire wire card

[Paul Delaney - K6HR]

http://kc.flexradio.com/KnowledgebaseArticle50179.aspx?Keywords=firewire


Paul Delaney - K6HR
paul.hamra...@verizon.net
http://k6hr.dyndns.org:8080 

> -Original Message-
> From: flexradio-boun...@flex-radio.biz [mailto:flexradio-bounces@flex-
> radio.biz] On Behalf Of y...@aol.com
> Sent: Wednesday, July 25, 2012 06:50
> To: flexradio@flex-radio.biz
> Subject: [Flexradio] fire wire card
> 
> need to buy a fire wire card the computer is a Intel I-5 with 4 gig ram
> and a open pci-e slot. running windows 7 64 bit. what should I buy?
> thanks
> dale wt4t
> ___
> FlexRadio Systems Mailing List
> FlexRadio@flex-radio.biz
> http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
> Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
> Knowledge Base: http://kc.flexradio.com/  Homepage:
> http://www.flexradio.com/


___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

Re: [Flexradio] QRZ article on memory buttons for Power SDR

[Paul Delaney - K6HR]

no link posted!

Paul Delaney - K6HR
paul.hamra...@verizon.net
http://k6hr.dyndns.org:8080 

> -Original Message-
> From: flexradio-boun...@flex-radio.biz [mailto:flexradio-bounces@flex-
> radio.biz] On Behalf Of WM3M
> Sent: Wednesday, June 27, 2012 08:10
> To: flexradio@flex-radio.biz
> Subject: [Flexradio] QRZ article on memory buttons for Power SDR
> 
> Saw article on QRZ.com, memory buttons for Power SDR, URL link below:
> 
> 
> QRZ article on Memory buttons for PowerSDR
> 
> ___
> FlexRadio Systems Mailing List
> FlexRadio@flex-radio.biz
> http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
> Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
> Knowledge Base: http://kc.flexradio.com/  Homepage:
> http://www.flexradio.com/


___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

[Flexradio] PSDR 2.3.5 Problem with VU5K

[Paul Delaney - K6HR]

Recently someone mentioned they were having problems with PSDR and the VU5K
module. Gerald replied asking for specific details of the problem.

I am a new owner of the VU5K module and hope to be able to make some
satellite contacts. I am using SatPC32 for doppler tuning and perhaps the
problem has something to do with the satellite program. I don't know if its
PSDR or SatPC32.

After attempting a satellite pass using the VU5K and returning to HF I
notice that VAC2 will no longer function. This can be 'cured' by doing a
database reset. A minor inconvenience, but perhaps something that needs to
be looked into.

I had posted a message to the reflector about this during Dayton and it got
lost in the shuffle

Paul Delaney - K6HR
paul.hamra...@verizon.net
http://k6hr.dyndns.org:8080 



___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

Re: [Flexradio] The 3000 dilemma

[Paul Delaney - K6HR]

Do you really expect anyone on the FLEX list to tell you to take an Icom?

Paul Delaney - K6HR
paul.hamra...@verizon.net
http://k6hr.dyndns.org:8080 

> -Original Message-
> From: flexradio-boun...@flex-radio.biz [mailto:flexradio-bounces@flex-
> radio.biz] On Behalf Of Dr. William J. Schmidt, II
> Sent: Tuesday, May 29, 2012 21:44
> To: flexradio@flex-radio.biz
> Subject: [Flexradio] The 3000 dilemma
> 
> Well I really have some choices to make this week and I'm looking for
> input
> (or consolation if you'd like).  I'm on my way to PJ4 very soon for 10
> days
> of vacation and operating.  I always take a radio with me when we travel
> to
> the Caribbean. I have a blast doing so. racking up lots of contacts
> wherever
> we go.  Up until now, I've always taken my Icom 756 Pro II and some
> dipoles.
> The problem is, The 756 plus the pelican box weighs in at the 50 lb limit
> .without the power supply and dipoles!
> 
> 
> 
> So this trip I figured I'd get smart. I take my laptop anyway, so I bought
> a
> Flex 3000 thinking I'd toss it in my briefcase as a much lighter solution.
> To prepare, over the past week, I've set up the station in the back yard
> and
> operated. just to get a feel for what was in store.  I also got a new
> antenna. a 3 element SuperAntenna YP3 which works out fine.
> but.radio-wise.results were not good.
> 
> 
> 
> My laptop is a Dell 630. has a built in fire-wire adapter, so it seemed ok
> as the software interface.  I figured it would be on the edge of
> processing
> power, but not wanting to invest yet another fortune in a laptop (just for
> vacations I might add) I stuck with it.  Truth is. it's at about 50%
> processing power or less.  Well about every 10th transmission, it hangs
> (never comes out of transmit).  I figured it was RF, so got a few clamp-on
> RF chokes for the fire wire and other cables.  It helps but it still hangs
> once in a while (which is majorly aggravating).  I tried some grounding
> configurations, but I guess you all know there isn't even a stud on the
> back
> of the radio to ground to.  So we're back to chokes for everything.  I
> could
> probably get things worked out if I had a couple more weeks to play with
> it..BUT.
> 
> 
> 
> Now the decision is. do I lug along the Icom 756. heavy, but tested. or do
> I
> take a chance and take (and possibly fight with) the 3000?  Flight leaves
> soon.
> 
> 
> 
> 
> 
> Dr. William J. Schmidt - K9HZ / J68HZ/ 8P6HK/ ZF2HZ/ PJ4HZ
> 
> 
> 
> Owner - Operator
> 
> Big Signal Ranch - K9ZC
> 
> Staunton, Illinois
> 
> 
> 
> email:   <mailto:b...@wjschmidt.com> b...@wjschmidt.com
> 
> 
> 
> ___
> FlexRadio Systems Mailing List
> FlexRadio@flex-radio.biz
> http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
> Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
> Knowledge Base: http://kc.flexradio.com/  Homepage:
> http://www.flexradio.com/


___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

[Flexradio] VU5K With Dual Band Yagi

[Paul Delaney - K6HR]

Is anyone using a 5000/VU5K with a dualband yagi for satellite work with any
positive results?

I recently put up a Gulf Alpha EZ Sat Dualband Satellite Yagi and it the
performance has been very disappointing. The Flex RX downlink is completely
'overwhelmed' during TX on the uplink. The RX panadapter shows a flat line
and a 10-20db rise during uplink TX effectively making my downlink signal
unusable in trying to find my signal on the transponder.

Before I ditch this antenna, I'd like to hear from anyone using a dualband
antenna for satellite work, and any suggestions they might have.

Paul Delaney - K6HR
paul.hamra...@verizon.net
http://k6hr.dyndns.org:8080 



___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

[Flexradio] MON Button Grayed Out - Buglet?

[Paul Delaney - K6HR]

I recently had a VU5K module installed and now I notice that when switching
from HF to UHF/VHF (to work a satellite pass) the MON button becomes grayed
out and stays that way even when I switch back to HF. If I shutdown PSDR
then restart it, the MON button is usable again. v 2.3.5

Is this a bug?

Paul Delaney - K6HR
paul.hamra...@verizon.net
http://k6hr.dyndns.org:8080 



___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

[Flexradio] No FWD PWR Indication Using VU5K

[Paul Delaney - K6HR]

With the TX Meter set to FWD PWR I see 0 watts output when TXing on 2m and
70cm FM or SSB makes no difference. Also SWR shows 0.

Is this normal for VU5K operation?

Paul Delaney - K6HR
paul.hamra...@verizon.net
http://k6hr.dyndns.org:8080 



___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

[Flexradio] Setup Loses ID AS Parameter

[Paul Delaney - K6HR]

I set my PSDR to Id As TS-2000 but I notice it does not hold this setting
when my Station Master stops working and I check the CAT Control tab in
Setup, the parameter has changed back to PowerSDR

Paul Delaney - K6HR
paul.hamra...@verizon.net
http://k6hr.dyndns.org:8080 




___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

Re: [Flexradio] Are these Microsoft Net framework updates ok to do?

[Paul Delaney - K6HR]

I have installed the updates you refer to yesterday and there are no ill
effects.


Paul Delaney - K6HR
paul.hamra...@verizon.net
http://k6hr.dyndns.org:8080 





___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

Re: [Flexradio] Trade my 2.5 month old K3 and P3 for loaded Flex5K+RX2+ATU+VU

[Paul Delaney - K6HR]

Good luck with that!

Paul Delaney - K6HR
paul.hamra...@verizon.net
http://k6hr.dyndns.org:8080 


> -Original Message-
> From: flexradio-boun...@flex-radio.biz [mailto:flexradio-bounces@flex-
> radio.biz] On Behalf Of Bret Mills
> Sent: Wednesday, April 25, 2012 06:58
> To: flexradio@flex-radio.biz
> Subject: [Flexradio] Trade my 2.5 month old K3 and P3 for loaded
> Flex5K+RX2+ATU+VU
> 
> Well I have came full circle,
> I sold my spare Flex5000 and purchased a K3 thinking I would use it for my
> spare Radio.
> 
> Well I have just out grown the KNOB radio's and would like to find someone
> who is un-happy or having troubles getting use to their newer
> Flex5000+RX2+ATU+VU and would like to trade for my Elecraft K3 / P3 and
> Flex5000+RX2+ATU+a
> LITTLE $ to make the cost even trade depending on the age of your FLEX of
> course.
> 
> The K3 / P3 are in BRAND NEW condition and contains all manuals, the K3 /
> P3
> was a kit and Box's were small so it wont fit in factory box's so I'll
> have
> to pack it in a different Box.
> Would like all the accessories that came with the FLEX including the
> Firewire cable, Power Cable and Box.
> 
> My K3 has the following
> Purchased 2/21/12
> 
> K3/100 K3 100W Xcvr. (Modular Kit) $1999.95
> KBPF3 K3 Gen. Cov. RX Module $149.95
> KDVR3 K3 Dig. Voice Recorder $129.95
> KTCXO3-1 K3 TCXO (0.5ppm) $99.95
> KXV3A K3 RX Ant, IF Out & Xvrtr Intf. $119.95
> KRX3 K3 2nd RX (Kit) $599.95
> KBPF3 K3 General Coverage RX Module $149.95
> KDVR3 K3 Digital Voice Recorder $129.95
> P3-K K3 Panadapter for K3 (Modular Kit) $699.95
> 
> Total with out shipping $3799.65
> Elecraft shipping $29.34
> 
> Total from Elecraft  $3828.99
> 
> 
> Filters, ALL INRAD 8 POLE (same as Elecraft Filters but less money in
> large
> quantity)
> RX 1
> 13.00KHz FM #725 Filter $112.00
> 6.00KHz AM #710 Filter $112.00
> 2.8KHz SSB #716 Filter $112.00
> 2.1KHz SSB #709 Filter $112.00
> 500Hz CW #728 Filter $112.00
> 
> RX 2
> 13.00KHz FM #725 Filter $112.00
> 6.00KHz AM #710 Filter $112.00
> 2.8KHz SSB #716 Filter $112.00
> 2.1KHz SSB #709 Filter $112.00
> 500Hz CW #728 Filter $112.00
> 
> Total with out Shipping $1120.00
> Shipping from INRAD $27.29
> 
> Total INRAD Filters with shipping $1147.29
> 
> Total investment for K3/P3 and INRAD Filters with shipping was $4976.28
> 
> Total K3 and INRAD Filters without shipping was $4919.65
> 
> Let me know
> 73's
> Bret Mills
> WX7Y
> 
> 
> --
> This message has been scanned for viruses and
> dangerous content by MailScanner, and is
> believed to be clean.
> 
> 
> ___
> FlexRadio Systems Mailing List
> FlexRadio@flex-radio.biz
> http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
> Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
> Knowledge Base: http://kc.flexradio.com/  Homepage:
> http://www.flexradio.com/


___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

[Flexradio] Fan Speed w/VU5K

[Paul Delaney - K6HR]

Is it normal for the fan to come on strong during VHF/UHF tx?


Paul Delaney - K6HR
paul.hamra...@verizon.net
http://k6hr.dyndns.org:8080 



___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

Re: [Flexradio] Sample rates

[Paul Delaney - K6HR]

http://kc.flexradio.com/Search.aspx?Keywords=sample rate

Paul Delaney - K6HR
http://k6hr.dyndns.org:8080
 
 
-Original Message-
From: flexradio-boun...@flex-radio.biz
[mailto:flexradio-boun...@flex-radio.biz] On Behalf Of Steven Hess
Sent: Sunday, April 15, 2012 12:41 PM
To: FlexRadio reflector
Subject: [Flexradio] Sample rates

Excuse me for having slept and forgot quite a bit.

Do I need to match all the sample rates to the selected bandwidth I chosen
on my Flex-3000?
So if I select 96k I need to match my VAC sample rate to 96K and my Windows
6 64 sound properties for my VAC inputs and output to 96K?
I have been running 48k forever and decided I wanted to zoom the panadapter
out more and would sacrifice some filter sharpness to do so.

Steven
-- 

Steven L Hess ARS KC6KGE DM05gd22
Google Voice 661 769 6201  +SMS
openSUSE Linux 12.1
___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage:
http://www.flexradio.com/


___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

[Flexradio] SatPC32 / DDUtil / Power SDR

[Paul Delaney - K6HR]

I thought I saw something on the list from a member who was using Sat32PC
through DDUtil to control his rotor and do doppler tuning in PowerSDR for
satellite work.

I am trying to get these programs working together and could use some advice
if available.

Paul Delaney - K6HR
paul.hamra...@verizon.net
http://k6hr.dyndns.org:8080 



___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

[Flexradio] Database Reset?

[Paul Delaney - K6HR]

Will I need to start a new database when I get my upgraded 5000 back in
service? Or will PSDR just recognize the new hardware and carry on?

Paul Delaney - K6HR
paul.hamra...@verizon.net
http://k6hr.dyndns.org:8080 



___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

Re: [Flexradio] Flex 5000 Audio Problem

[Paul Delaney - K6HR]

I had a similar problem and discovered that I had the Windows 'playback' and
'recording' properties of the VAC cables set to different sampling rates. 

Paul Delaney - K6HR
http://k6hr.dyndns.org:8080
 
 
-Original Message-
From: flexradio-boun...@flex-radio.biz
[mailto:flexradio-boun...@flex-radio.biz] On Behalf Of W6SDM Steve
Sent: Sunday, March 18, 2012 7:01 PM
To: flexradio@flex-radio.biz
Subject: [Flexradio] Flex 5000 Audio Problem

I am hearing my mic audio and CW through the system speakers.  It sounds as
if there's an echo on SSB.  Here's my configuration:


Flex 5000A with  PowerSDR 2.3.5 running VAC 4.11.  Computer is  a Shuttle
i7 running Windows 7 Ultimate.  I have VAC 1 and 2 working in PowerSDR.  I
have disabled both and have the same results.


Bose Companion 2 speakers are plugged directly in to the back of the Flex.
I
tried a different set of speakers and have the same problem.  Even if I
turn the computer system sound all the way down, I have the problem.


If I look at the audio Volume Mixer in Windows  I have one device,
speakers, which is set for  (speakers, Realtek High Definition Audio).  I
muted everything including the computer speakers and have the same problem.


In the mixer window, I can see all 8 of my virtual audio cables plus a
Realtek Digital Audio that are not selected.  The applications that are
present under the volume mixer window are System sounds, CommCat spot
manager, Mozilla Firefox, and Flex Radio Systems PowerSDR.


I know it's not RF because I get the audio feedback even with the amp off
and power output set to zero.  The only way to stop the feedback is to turn
the Companion 2 speakers all the way down, or unplug them.


What am I missing here?



Steve

W6SDM


-- 
Steve Miller
w6sdm.net
___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage:
http://www.flexradio.com/


___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

Re: [Flexradio] One gotcha with PowerSDR 2.3.5 and SDR Data Transfer

[Paul Delaney - K6HR]

Yeah the logoI love Flex but the logo is somewhat of a distraction.

Paul Delaney - K6HR
http://k6hr.dyndns.org:8080
 
 

-Original Message-
From: flexradio-boun...@flex-radio.biz
[mailto:flexradio-boun...@flex-radio.biz] On Behalf Of Alan NV8A
Sent: Monday, March 05, 2012 2:06 PM
To: FlexRadio Reflector
Subject: [Flexradio] One gotcha with PowerSDR 2.3.5 and SDR Data Transfer

I installed the new version, then transferred my previous settings using 
SDR Data Transfer with the updated data -- and overwrote the 60M 
bandstack data, with the result that only two (or was it three?) of the 
clicks on the 60M button corresponded to the new channels. I saved a 
copy of the database, reset to the default, then copied the 60M 
bandstack data from the default file to the saved file. All is now well.

Perhaps Ray should include an "Are you sure your really want to do 
that?" dialog in his program specifically for 60M.

I think I will like the new 2012 Default skin, and I'll even put up with 
the FlexRadio logo on the panadapter screen.

73

Alan NV8A

___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage:
http://www.flexradio.com/


___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

[Flexradio] Flex 1500 Sold!

[Paul Delaney - K6HR]

Thanks to all who inquired!

Paul Delaney - K6HR
paul.hamra...@verizon.net
http://k6hr.dyndns.org:8080 




___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

[Flexradio] FW: FLEX 1500 FOR SALE $575

[Paul Delaney - K6HR]

I have decided to sell my FLEX 1500 and install an RX2 unit into my 5000A
instead. This radio is super clean and in minty condition. I used this 1500
as the second receiver for my Analog/Digital SSTV website. Not much TX time
other than an occasional tune or test signal. Includes original box, USB
cable, power lead, and paperwork. I am the original owner and a non smoker.
PayPal instant payment only. Serious inquiries only please. $575

Paul Delaney - K6HR
paul.hamra...@verizon.net
http://k6hr.dyndns.org:8080 




___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

[Flexradio] FLEX 1500 FOR SALE

[Paul Delaney - K6HR]

I have decided to sell my FLEX 1500 and install an RX2 unit into my 5000A
instead. This radio is super clean and in minty condition. I used this 1500
as the second receiver for my Analog/Digital SSTV website. Not much TX time
other than an occasional tune or test signal. Includes original box, USB
cable, power lead, and paperwork. I am the original owner and a non smoker.
PayPal instant payment only. Serious inquiries only please. I'll include
FREE SHIPPING if the buyer pays the PayPal fee.

Paul Delaney - K6HR
paul.hamra...@verizon.net
http://k6hr.dyndns.org:8080 




___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

[Flexradio] RX2 Antenna Question

[Paul Delaney - K6HR]

The KC article states:

2.The ability to have RX2 tap off of the RX1 signal path post the RX loop
(RX1-TAP)

Does this mean I can have both RX1 and RX2 share the same RX antenna?

Paul Delaney - K6HR
paul.hamra...@verizon.net
http://k6hr.dyndns.org:8080 




___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

[Flexradio] VU5K Power Preamps Through Coax?

[Paul Delaney - K6HR]

Will the F5K + VU5K power my satellite preamps through the coax?

Paul Delaney - K6HR
paul.hamra...@verizon.net
http://k6hr.dyndns.org:8080 



___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

Re: [Flexradio] Flex 5000 Speakers

[Paul Delaney - K6HR]

Samson Media One 3a's are also nice:


http://www.samsontech.com/samson/products/studio-monitors/media-one/mediaone
3a/

Paul Delaney - K6HR
paul.hamra...@verizon.net
http://k6hr.dyndns.org:8080 

> -Original Message-
> From: flexradio-boun...@flex-radio.biz [mailto:flexradio-bounces@flex-
> radio.biz] On Behalf Of Edwin Marzan
> Sent: Friday, January 20, 2012 09:33
> To: franklin6...@att.net; flexradio@flex-radio.biz
> Subject: Re: [Flexradio] Flex 5000 Speakers
> 
> 
> I use these and they sound great and look nice. YMMV
> 
> Creative GigaWorks T20 Series II 2.0 Multimedia Speaker System with
> BasXPort Technology
> 
> About 95 bucks on Amazon.
> 
> 
> Edwin Marzan AB2VW
> 
> 
> > Date: Fri, 20 Jan 2012 12:05:44 -0500
> > From: franklin6...@att.net
> > To: flexradio@flex-radio.biz
> > Subject: [Flexradio] Flex 5000 Speakers
> >
> > I am sure this has been asked many times but I am new to Flex
> > Radio. Can anyone recommend a set of good speakers I can use on my
> > Flex 5000?
> >
> > Thanks
> > Gary , K8BKB
> >
> > ___
> > FlexRadio Systems Mailing List
> > FlexRadio@flex-radio.biz
> > http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
> > Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
> > Knowledge Base: http://kc.flexradio.com/ Homepage:
> http://www.flexradio.com/
> 
> ___
> FlexRadio Systems Mailing List
> FlexRadio@flex-radio.biz
> http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
> Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
> Knowledge Base: http://kc.flexradio.com/  Homepage:
> http://www.flexradio.com/


___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

Re: [Flexradio] Flex-1500 PSDR 'FlexControl' Form

[Paul Delaney - K6HR]

http://lmgtfy.com/?q=flexcontrol

Paul Delaney - K6HR
paul.hamra...@verizon.net
http://k6hr.dyndns.org:8080 

> -Original Message-
> From: flexradio-boun...@flex-radio.biz [mailto:flexradio-bounces@flex-
> radio.biz] On Behalf Of Don May
> Sent: Wednesday, January 18, 2012 15:59
> To: flexradio@flex-radio.biz
> Subject: [Flexradio] Flex-1500 PSDR 'FlexControl' Form
> 
> 
> Flexers,
> 
> So...another area I can't find in the current Flex-1500 manual...the PSDR
> top tab line "FlexControl" form?
> 
> Is this applicable to some particular type of external USB controller?
> 
> I already use a Griffen Technologies PowerMate USB controller which is
> useful for very fine frequency (1Hz/10Hz) control/tuning on CW/SSB and
> during FMTs.
> 
> Don / N5DM
> ___
> FlexRadio Systems Mailing List
> FlexRadio@flex-radio.biz
> http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
> Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
> Knowledge Base: http://kc.flexradio.com/  Homepage:
> http://www.flexradio.com/


___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

Re: [Flexradio] Working satellites with a Flex 5000

[Paul Delaney - K6HR]

I'm considering the purchase of a VU5K for satellite work alsocomments
most welcome! Anyone using SatPC32 with VU5K?


Paul Delaney - K6HR
paul.hamra...@verizon.net
http://k6hr.dyndns.org:8080 

> -Original Message-
> From: flexradio-boun...@flex-radio.biz [mailto:flexradio-bounces@flex-
> radio.biz] On Behalf Of kd6...@verizon.net
> Sent: Sunday, January 15, 2012 21:49
> To: flexradio@flex-radio.biz
> Subject: [Flexradio] Working satellites with a Flex 5000
> 
> Folks,
> 
> I'm looking at replacing an FT-736 used occasionally for satellite work.
> I'd like to have the best of both worlds and replace it with a software
> defined radio.  What are your general experiences working satellites with
> the 5K?  I'm interested from both a hardware (the VU5K module) and a
> software perspective. Are there 3rd party software add-ons that you feel
> are
> a "must have" ?
> 
> Thanks in advance,
> 
> Mark
> kd6not
> 
> 
> 
> ___
> FlexRadio Systems Mailing List
> FlexRadio@flex-radio.biz
> http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
> Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
> Knowledge Base: http://kc.flexradio.com/  Homepage:
> http://www.flexradio.com/


___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

[Flexradio] Running 1500 and 5000 on same machine?

[Paul Delaney - K6HR]

How does one make this work? I can start two instances of PSDR but they both
see only the 5000. Can anyone tell me the trick to get both radios running
at the same time on one PC?

Thanks!

Paul Delaney - K6HR
paul.hamra...@verizon.net
http://k6hr.dyndns.org:8080 



___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

[Flexradio] Two Instances of PSDR On Same PC? 1500

[Paul Delaney - K6HR]

I looked at the KB article but it doesn't mention the 1500.
Is it possible to run TWO 1500's on the same PC simultaneously?

Paul Delaney - K6HR
paul.hamra...@verizon.net
http://k6hr.dyndns.org:8080 



___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

[Flexradio] Low Cost Laptop For Flex 1500

[Paul Delaney - K6HR]

I have a Dell Inspiron B130 laptop for sale. Works great with PSDR 2.2.23
and my Flex 1500. Very stable with a display rate of 35fps in PSDR. Has
Windows XP SP3, Intel Pentium M 1.7ghz processor, 512MB RAM, 40GB HDD,
CDRW/DVD. Will include USB Optical Mouse, Dell System Restore CD, and power
supply. PSDR and turboencabulator interface already installed.

Please note: The touchpad mouse is not working, but can most likely be fixed
by reinserting the flat ribbon cable. (my fingers cannot get inside)

Just $160 takes it! Shipping included!

Paul Delaney - K6HR
paul.hamra...@verizon.net
http://k6hr.dyndns.org:8080 



___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

Re: [Flexradio] New PC Wow

[Paul Delaney - K6HR]

I also use the i7 2600K cpu, identical setup except for the mobo, fantastic for 
running PSDR for my 5000. I can also run every other program I wish without so 
much as a hiccup.

Paul Delaney - K6HR
http://k6hr.dyndns.org:8080
  - Original Message - 
  From: David Edwards 
  To: flexradio@flex-radio.biz 
  Sent: Friday, December 23, 2011 12:13 PM
  Subject: [Flexradio] New PC Wow


  Running PSDR 2.2.3 and a 5000A
  Recent upgrade from Pentium 4, 3.3 GHZ  XP Home and 3GB memory.
  New ASUS P8Z68-V Pro MB with Intel, i7 2600K Quad core, 120 GB SSD(s) in Raid 
5, 16 GB memory.

  Huge improvement in PSDR performance across the board but the things that are 
very noticeable
  1. CPU usage with noise blanker on was 60% now 8%.
  2. Could not run 190k sample rate or less then 2048 buffer now 190K and 1024 
Buffer.
  3. There was always a long echo on the monitor, now its real time no apparent 
echo I can finally adjust the audio with a usefull monitor

  Tim was right when he recommended an upgrade the old Pentium wasn't up to SDR 
even with GBoost

  Happy holidays to all and thanks for all the help to the many who have 
responded when I've had issues

  Loving my Flex 5K
  de
  WB1S
  ___
  FlexRadio Systems Mailing List
  FlexRadio@flex-radio.biz
  http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
  Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
  Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/
___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

[Flexradio] Flex Jacket

[Paul Delaney - K6HR]

How about offering a nice Flex jacket?
The XYL had just suggested getting me one (with a Flex hat) for the
holidays.

Anybody else interested?

Paul Delaney - K6HR
paul.hamra...@verizon.net
http://k6hr.dyndns.org:8080 



___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

Re: [Flexradio] Output power issue

[Paul Delaney - K6HR]

Is this even possible?
  Being Field Day, there was a lot of out band RF around so I put it down to
  perhaps out of band RF coming back into the TX and being interpreted as
  Reflected power by the TX protection circuitry which as a result throttled
  back the TX PO.
___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

Re: [Flexradio] Voice Keyer

[Paul Delaney - K6HR]

Check this out. Works great with PSDR: 
http://kc.flexradio.com/KnowledgebaseArticle50275.aspx
  - Original Message - 
  From: Dave Mayfield W9WRL 
  To: flexradio@flex-radio.biz 
  Sent: Sunday, November 27, 2011 3:08 PM
  Subject: [Flexradio] Voice Keyer


  Anyone have any info if power SDR will have a voice keyer built in? 
  Seems like a very basic feature.

  ___
  FlexRadio Systems Mailing List
  FlexRadio@flex-radio.biz
  http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
  Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
  Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/
___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

[Flexradio] Fw: Station Master With Flex5000

[Paul Delaney - K6HR]

How do I "configure the Flex for external control using the TS-870 emulation" 
as suggested below?


- Original Message - 
From: Joe Subich, W4TV 
To: Paul Delaney - K6HR 
Sent: Sunday, November 13, 2011 1:36 PM
Subject: Re: Station Master With Flex5000



It is used when the Flex provides the Kenwood compatible interface
on a serial port.  As I said before:

 >Station Master does not support Flex unless you configure the
 >Flex for external control using the TS-870 emulation.

If the Flex is configured to emulate Kenwood (see your documentation),
Station Master and microHAM Router can be configured as if it were
controlling a Kenwood transceiver (see the Station Master User Manual).

73,

   ... Joe Subich, W4TV
   microHAM America
   http://www.microHAM-USA.com
   http://groups.yahoo.com/group/microHAM

   support e-mail: supp...@microham.com


On 11/13/2011 3:33 PM, Paul Delaney - K6HR wrote:
> Hi Joe,
>
> Thanks for the fast reply!
> If the SM is not compatible with the Flex/PowerSDR/DDUtil what is the Flex 
> cable used for?
>
> Flex-Radio (PowerSDR):
>  CAT-RS232-YX  SDR-1000, Flex-5000
>
>- Original Message -----
>    From: Joe Subich, W4TV
>To: Paul Delaney - K6HR
>Sent: Sunday, November 13, 2011 11:44 AM
>Subject: Re: Station Master With Flex5000
>
>
>
>Station Master does not support Flex unless you configure the
>Flex for external control using the TS-870 emulation.  Station
>Master requires direct access to the transceiver serial port
>(RS-232, TTL or CI-V) with a Kenwood, Icom, Ten-Tec or Yaesu
>command set.
>
>microHAM does not support Flex in any form.
>
>73,
>
>   ... Joe Subich, W4TV
>   microHAM America
>   http://www.microHAM-USA.com
>   http://groups.yahoo.com/group/microHAM
>
>   support e-mail: supp...@microham.com
>
>
>On 11/13/2011 2:11 PM, Paul Delaney - K6HR wrote:
>>
>>  I plan to purchase the Station Master for use with PowerSDR and a Flex 
> 5000
>>  and have a question:
>>
>>  I see a cable is available for the Flex. Does the cable eliminate the 
> need
>>  for DDUtil? Can you tell me exactly how the SM connects and communicates
>    >  with the PSDR/Flex 5000? Does it need the cable AND DDUtil? I'm not 
> able to
>>  discern this from the documentation found online.
>>
>>  Paul Delaney - K6HR
>>  paul.hamra...@verizon.net
>>  http://k6hr.dyndns.org:8080
>>
>>
>>
___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

[Flexradio] Band Decoder For Power SDR

[Paul Delaney - K6HR]

I would like to have my Six Pack antenna switch connected to PowerSDR. I
understand I need a band decoder. Is anyone using a MicroHam Station Master
or Array Solutions Band Master with the Flex?

What is the recommended/proven way to accomplish this? 

Paul Delaney - K6HR
paul.hamra...@verizon.net
http://k6hr.dyndns.org:8080 



___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

[Flexradio] Bandmaster II Decoder

[Paul Delaney - K6HR]

Is there anyone on the reflector using an Array Solutions Bandmaster II with
a Flex 5000 that can share some setup details? I have the documentation but
I'm not sure which configuration to use for the Flex. There are choices for
several radios ICOM, KENWOOD, YAESU etc. but nothing specific to the Flex.

Any tips would be most welcome!

Paul Delaney - K6HR
paul.hamra...@verizon.net
http://k6hr.dyndns.org:8080 



___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

Re: [Flexradio] Enhancement Requests

[Paul Delaney - K6HR]

Yeah, way back when I was a legacy radio user, I would constantly try to
submit my feature requests to the big three. Well, you know where that got
me...At least with Flex there is the possibility. I'm trying to guess how
many of the "640+" requests you refer to actually made any sense. Meanwhile
I'm enjoying all the enhancements that are already included in PSDR! 

Paul Delaney - K6HR
paul.hamra...@verizon.net
http://k6hr.dyndns.org:8080 

> -Original Message-
> From: flexradio-boun...@flex-radio.biz [mailto:flexradio-bounces@flex-
> radio.biz] On Behalf Of David Painter
> Sent: Thursday, November 03, 2011 03:06
> To: flexradio@flex-radio.biz
> Subject: [Flexradio] Enhancement Requests
> 
> Not surprisingly the 640+ enhancement requests, going back to 2006, have
> now been removed from the FRS site.
> 
> I suppose it is easier to remove these 640+ requests than it is to provide
> Flex customers with the functionality they have been saying, for years,
> they want.
> 
> A new methodology has been introduced for 'Feature Requests' (see previous
> emails re the FRS Assistance Centre or click on Enhancement Requests under
> the Support tab on the main FRS site). I would encourage those of you who
> want to waste more of your time, to resubmit your enhancement requests to
> this new facility and see if you have any better luck over the next 5
> years.
> 
> G4PNX
> ___
> FlexRadio Systems Mailing List
> FlexRadio@flex-radio.biz
> http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
> Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
> Knowledge Base: http://kc.flexradio.com/  Homepage:
> http://www.flexradio.com/


___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

[Flexradio] Band Decoder w/5000A

[Paul Delaney - K6HR]

I'm considering the purchase of a band decoder to use with my 5000a and my 
Array Solutions Six-Pack antenna switch. I am interested in hearing from hams 
that are using a similar setup. I'm particularly interested in how they are 
connected to the Flex and if the decoder needs to be connected directly to the 
Flex or through DDUtil.

All advice, opinions, and recommendations would be most welcome!

Paul Delaney - K6HR
http://k6hr.dyndns.org:8080
___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

Re: [Flexradio] Band/ freq changes after shutoff

[Paul Delaney - K6HR]

That's interesting. 
My PSDR always starts up where it left off, the settings do not change as the 
others have described.
I also always shutdown the software before the hardware. (and vice versa)

Paul Delaney - K6HR
http://k6hr.dyndns.org:8080
  - Original Message - 
  From: k8...@aol.com 
  To: k...@arrl.net ; scott.wa4...@gmail.com ; flexradio@flex-radio.biz 
  Sent: Friday, October 14, 2011 4:16 PM
  Subject: Re: [Flexradio] Band/ freq changes after shutoff


  I hope you are shutting down your PowerSDR software first. If you don't it  
  will revert to the last settings you had when you exited the Setup menu.
   
  Bob
  K8MLM
   
   
  In a message dated 10/14/2011 6:41:50 P.M. Eastern Daylight Time,  
  rpmar...@comcast.net writes:

  My 5000A  has done that since the day I've owned it.  I have never figured
  out  why sometimes it remembers where I left it when it was shut off,  and
  sometimes it doesn't.  Every version of Power SDR has done  this.  I've
  always assumed it was something I was doing incorrectly,  or some box I
  neglected to check, but darned if I've been able to figure it  out.  I 
  always
  stop Power SDR first, and then close the  application

  If there's a simple answer to this, I'd love to hear  it.  I've just learned
  to live with it.

  de Rick,  KN3C


  -Original Message-
  From: Scott Simmons - WA4DOS  [mailto:scott.wa4...@gmail.com] 
  Sent: Friday, October 14, 2011  18:19
  To: flexradio@flex-radio.biz
  Subject: [Flexradio] Band/ freq  changes after shutoff


  Folks, I noticed after upgrading to V.2.2.3  about a month or so ago, that
  the band and frequency changes from the  previous operating session. When I
  fire up the next time, the rig is on a  different band and freq...As an
  example, I'm on 14.300 MHz and then shut  down PowerSDR and turn off the 
  rig.
  The next day the band and freq is  somewhere else (ie:40 meters). I believe
  this behavior is pretty  consistent.

  Any ideas? Would resetting to factory defaults fix the  anomaly?



  Flex 5000A with single RX, V2.2.3, ... ZT Systems PC,  Quad Core 3.2 MHz 
  CPU,
  8GB RAM running WIN 7 Premium OS 

  Scott S. -  WA4DOS  



  ___
  FlexRadio  Systems Mailing  List
  FlexRadio@flex-radio.biz
  http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
  Archives:  http://www.mail-archive.com/flexradio%40flex-radio.biz/
  Knowledge Base:  http://kc.flexradio.com/  Homepage:  
  http://www.flexradio.com/

  ___
  FlexRadio Systems Mailing List
  FlexRadio@flex-radio.biz
  http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
  Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
  Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/
___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

Re: [Flexradio] Flex 3K and 5K software shut down QRO.

[Paul Delaney - K6HR]

Same problem here. Found out it was the computer keyboard that was picking
up the RF. Purchased a wireless keyboard and mouse...end of problem.

Paul Delaney - K6HR
paul.hamra...@verizon.net
http://k6hr.dyndns.org:8080 


> -Original Message-
> From: flexradio-boun...@flex-radio.biz [mailto:flexradio-bounces@flex-
> radio.biz] On Behalf Of William H. Fite
> Sent: Monday, September 12, 2011 07:57
> To: Neal Campbell
> Cc: flexradio@flex-radio.biz
> Subject: Re: [Flexradio] Flex 3K and 5K software shut down QRO.
> 
> I, like the others who've checked in here, have put ferrites on every
> single
> cable in the shack.  It seems like overkill but I've had absolutely no
> issues with RF since doing so.  Also, of course, be sure that your station
> ground is really good, ground wires or straps are as short as possible,
> and
> all that stuff that you doubtless have done already.
> 
> Good luck.  You'll find the entry point sooner or late.  Hopefully sooner.
> 
> Bill
> 
> 
> 
> On Mon, Sep 12, 2011 at 9:41 AM, Neal Campbell
> wrote:
> 
> > You might try an isolator from RFWorks between the antenna and your
> shack.
> > That or an UNUN/BALUN depending on your antenna situation.
> >
> > BTW, what are your antennas?
> >
> > 73
> > Neal
> >
> > On Mon, Sep 12, 2011 at 8:54 AM, W1JCW  wrote:
> >
> > > No luck adding the ground or the two chokes on each end of the fire
> ware
> > > cable.
> > >
> > > It seems just 20m even when I don't use my Acom 2k. If I turn the
> drive
> > up
> > > to 75w
> > > the audio cuts in and out and I can hear the relays in the 5K.
> > >
> > > All other bands qro are fine, no issue.
> > >
> > > Must be some harmonic on 20m getting into the box or feeding back into
> > it.
> > >
> > > Suggestions ??
> > >
> > > 73-
> > > W1JCW
> > > John
> > >
> > >
> > > From: W1JCW
> > > Sent: Friday, September 09, 2011 8:44 AM
> > > To: Ray, K9DUR
> > > Subject: Flex 3K and 5K software shut down QRO.
> > >
> > >
> > > I don't have a ground on the PC so I'll add that tonight and see how
> it
> > > works.
> > >
> > > I did have a choke on each end of the fw cable but that didn't work
> but I
> > > had no ground then.
> > > I'll put a choke on each end of the fw if adding the ground on the PC
> > > doesn't work.
> > >
> > > Stay tuned.
> > >
> > > Thanks for the replies.
> > >
> > > 73-
> > > W1JCW
> > > John
> > >
> > >
> > > From: Ray, K9DUR
> > > Sent: Thursday, September 08, 2011 8:11 PM
> > > To: fmeac...@aol.com ; flexradio@flex-radio.biz
> > > Subject: Re: [Flexradio] Current Flex 3000 software shuts down when
> > > runninghigh power.
> > >
> > >
> > > Frank,
> > >
> > > That definitely sounds like RF feedback.  The most likely culprit is
> the
> > > firewire cable.  I had the same issue running my amp with my FLEX-
> 5000A.
> > >
> > > First, make certain that your PC is connected to the shack ground.
> After
> > > all, it is better than half of the radio.
> > >
> > > If you are using the stock firewire cable that came with the rig,
> replace
> > > it
> > > with the one by Granite Digital.  Is costs about $40 & is availabel
> from
> > > Flex.
> > >
> > > Finally, if you still are having problems, add ferrite chokes at each
> end
> > > of
> > > the firewire cable.
> > >
> > > The above steps eliminated my RF feedback problems entirely.  Now I
> can
> > run
> > > 1kW on all bands with no issues.
> > >
> > > 73, Ray, K9DUR
> > > http://k9dur.info
> > > ___
> > > FlexRadio Systems Mailing List
> > > FlexRadio@flex-radio.biz
> > > http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
> > > Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
> > > Knowledge Base: http://kc.flexradio.com/  Homepage:
> > > http://www.flexradio.com/
> > >
> >
> >
> >
> > --
> > Abroham Neal Software
> > www.abrohamnealsoftware.com
> > Work:(540) 645 5394
> > Mobile:(540) 645 8171
> >  ___
> > FlexRadio Systems Mailing List
> > FlexRadio@flex-radio.biz
> > http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
> > Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
> > Knowledge Base: http://kc.flexradio.com/  Homepage:
> > http://www.flexradio.com/
> >
> ___
> FlexRadio Systems Mailing List
> FlexRadio@flex-radio.biz
> http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
> Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
> Knowledge Base: http://kc.flexradio.com/  Homepage:
> http://www.flexradio.com/


___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

Re: [Flexradio] help

[Paul Delaney - K6HR]

I had the same problem and it was the LPT address. All i had to do was type the 
correct address in over the address that was showing...and it worked.

  - Original Message - 
  From: Al K0VM 
  To: flexradio@flex-radio.biz ; kc...@wildblue.net 
  Sent: Monday, September 05, 2011 2:40 PM
  Subject: Re: [Flexradio] help


  Jim,
  The symtoms you describe are consistant with lack of communications 
  on  SDR-1000 control cable..
  This could be  the radio not turned on.  Or the control cable not 
  connected ( or missing wires in the parallel cable ) or not configured 
  correctly ( in correct LPT address).  Or If you have the Flex USB to 
  parallel cable, the Driver could be missing or not installed correctly, 
  or the Flex USB to Parallel cable could be defective.   An non-Flex USB 
  to Parallel converter is not likely to work ever.

  AL, K0VM


  On 9/5/2011 12:00 PM, flexradio-requ...@flex-radio.biz wrote:
  > Date: Sun, 4 Sep 2011 11:26:29 -0400
  > From: James Sheehan<>
  > To:FlexRadio@flex-radio.biz
  > Subject: [Flexradio] help
  > Message-ID:
  > 
  > Content-Type: text/plain; charset=ISO-8859-1
  >
  > Can anyone help me with this SDR 1000 with a delta 44 card. Everything load
  > into the computer just fine when power sdr comes up and I hit the start
  > button the radio go right into mox and it tell me there is a High swr .I
  > have a 1:1 swr and my other flex works just .I just got this 1000 the other
  > day I have it on windows xp pro 2giz computer with 2 giz of ram no other
  > program on this machine except flex radio and few programs .Help
  >
  > Jim KC1CS
  >


  ___
  FlexRadio Systems Mailing List
  FlexRadio@flex-radio.biz
  http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
  Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
  Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/
___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

Re: [Flexradio] Power_SDR Release

[Paul Delaney - K6HR]

I think he meant an adjustable manual notch filter that could be moved around 
within the passband. This would be handy since now one has to shrink or shift 
the BPF window itself. CMIIW.
  - Original Message - 
  From: W1JCW 
  To: flexradio@flex-radio.biz 
  Sent: Friday, July 22, 2011 8:30 PM
  Subject: [Flexradio] Power_SDR Release


  What is a track able notch ?? 

  73-
  W1JCW
  John


  From: Michael Tondee 
  Sent: Friday, July 22, 2011 9:49 PM
  To: flexradio@flex-radio.biz 
  Subject: Re: [Flexradio] ANNOUNCEMENT: POWERSDR v2.1.5 OFFICIAL RELEASE


  Does this release include the trackable notch? Or are we still waiting 
  on that?
  Tnx and 73,
  Michael, W4HIJ
  ___
  FlexRadio Systems Mailing List
  FlexRadio@flex-radio.biz
  http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
  Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
  Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/
___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

Re: [Flexradio] [FlexRadio] SSHD Recommendations

[Paul Delaney - K6HR]

I use two Kingston 128gb SSD's in RAID 0.
Under Win & 64 bit.
Installs like any other drive.
Lightning fast.
  - Original Message - 
  From: DALE HANKINS 
  To: 'Don' ; FlexRadio@flex-radio.biz 
  Sent: Sunday, May 01, 2011 9:00 PM
  Subject: Re: [Flexradio] [FlexRadio] SSHD Recommendations


  I bought a Kingston 60 gig SSHD works great with WWindows 7 and all programs
  needed for my Flex. Paid $84.00 after rebate tiger direct. Didn't do
  anything different than regular drive.
  Dale
  Kb5ve

  -Original Message-
  From: flexradio-boun...@flex-radio.biz
  [mailto:flexradio-boun...@flex-radio.biz] On Behalf Of Don
  Sent: Sunday, May 01, 2011 10:16 PM
  To: FlexRadio@flex-radio.biz
  Subject: [Flexradio] [FlexRadio] SSHD Recommendations

  I'm interested in the SSHD drives.



  I understand that SSHD's are not necessarily "Plug & Play" like a standard
  hard drive or is my understanding incorrect?



  My motherboard is an Asus P5K Premium/WiFi-AP and I have looked thru the
  manual and nothing is mentioned about the SSHD's. 



  http://www.asus.com/Motherboards/Intel_Socket_775/P5K_PremiumWiFiAP/



  OS is Win 7-64



  How do I determine if my system can use one?



  Don
  ___
  FlexRadio Systems Mailing List
  FlexRadio@flex-radio.biz
  http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
  Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
  Knowledge Base: http://kc.flexradio.com/  Homepage:
  http://www.flexradio.com/


  ___
  FlexRadio Systems Mailing List
  FlexRadio@flex-radio.biz
  http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
  Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
  Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/
___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

Re: [Flexradio] PSDR Doesn't Fit on Screen (Now Fixed)

[Paul Delaney - K6HR]

The problem I had here was there was nothing visible to the right of the
panadapter. So all the band buttons, s meter and filters were gone.

Believe it or not PSDR stopped responding once, and after restarting
everything now appears on the screen!

Paul Delaney - K6HR
paul.hamra...@verizon.net
http://k6hr.dyndns.org:8080 

-Original Message-
From: flexradio-boun...@flex-radio.biz
[mailto:flexradio-boun...@flex-radio.biz] On Behalf Of G0DDX
Sent: Friday, April 08, 2011 09:03
To: flexradio@flex-radio.biz
Subject: [Flexradio] PSDR Doesn't Fit on Screen (Now Fixed)

 

 

From: br...@lloyd.com [mailto:br...@lloyd.com] On Behalf Of Brian Lloyd
Sent: 07 April 2011 19:01
To: Lee Mushel
Cc: G0DDX
Subject: Re: [Flexradio] PSDR Doesn't Fit on Screen

 

 

On Thu, Apr 7, 2011 at 10:28 AM, Lee Mushel  wrote:

Guys,

I've been reading these  "screen size" complaints on the reflector for
several years now and have never understood what the problem was.   If I
want the console display bigger I just "mouse-pull" it to size and move it
slightly, if required.  This works with displays from 14 to 32 inch anyway.
And I've been doing this without trouble ever since I first received the
5000A.   And my experience with the 3000 and it's little 14 inch screen has
been the same.   If I change software versions I do have to "drag and pull"
again but never any trouble.   But my curiosity keeps increasing.   I guess
I would appreciate some insight into what it is that bothers people.  On the
screen sitting on top of my "emmcom" package you see that the "height" does
not completely fill the screen---but all I have to do is "drag it taller."

 

The problem is when the physical screen has a height or width less than the
minimum to display all of the PSDR screen. Then when you want to use the
buttons at the bottom of the PSDR screen, the buttons at the top are off the
screen. When you move the PSDR window so you can see the buttons at the top,
the buttons at the bottom disappear off the bottom. It is annoying. It would
have been -*MUCH*- better if PSDR had been made up of multiple, smaller
windows that you could move around or overlay as you see fit. I only use
about 1/2 the controls so I would much rather be able to put them up-front
and cover the ones I never use. 

 

-- 
Brian Lloyd, WB6RQN/J79BPL
3191 Western Dr.
Cameron Park, CA 95682
br...@lloyd.com
+1.767.617.1365 (Dominica)
+1.931.492.6776 (USA)
(+1.931.4.WB6RQN)

 

 

Guys,

The problem is that the only settings I get for the screen size
with my Acer D255 Netbook is 1024 x 600 and 800 x 600.

It will not do any other resolution (well none are offered ) The Native Mode
for these 10.1" Acer screens is 1024 x 600. You can't drag the programme
screen to fit, as the screen just isn't big enough to accommodate the entire
picture in one go, and it wont scroll up or down either (This is Windows not
Linux!!).

 

However, some ferreting  around and I came up with this:

 

1.There is a utility called "a1ctl" utility I do not know where this
comes from or where it is available. However, it does NOT work on Windows 7,
although it may be of some use to anyone running XP.

2.I did come up with this off a techie forum for Windows 7.

 

Ok, anyone with an Acer Aspire one on Win 7 can forget about screen res
settings and a1ctl programs, they won't fix the problem.
However there is a way, if your comfortable editing your register..
Go to Run command, type regedit and enter.
Once in here don't mess around.
Select
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Video\{FEE9B7B8-B684-444
A-BB90-505CAF0F90E4} 
Now in sub folder  select entry display1 downscaling support and set it
to 1 instead of 0.
Save your settings and exit.
Now go to your display adapters setting and you will be able to set screen
res to what you want.#

 

Now, I tried to find this setting and could not (lost it after the \Video).
So I did a search in the Registry for "Downscaling" and found an entry in
the same tree branch as above.

I carefully noted where it was so I could revert if need be. I changed it
from a 0 (zero) to a 1 as suggested.

Low and behold, I can now set my screen to 1024 x 768 which supports PSDR.
Yippee!!!   Job Done.

 

The only downside I can see is the pictures are a bit stretched,  as its low
ceiling screen displaying a taller screen.

Still it Works and seems to work well.

 

The problem is the Aspire One series of Netbooks have limited controls,
coupled with the fixed size of PSDR, it caused the problem of not being able
to see the buttons at the bottom of the screen.

 

I hope this snippet of information will be of help to others with Limited
screen sizes.

I thought I was going to have to trade in a new netbook for another just
because I could not run PSDR.

 

 

 

Best Regards

 

Geoff

G0DDX

 

_

[Flexradio] PSDR Doesn't Fit on Screen

[Paul Delaney - K6HR]

I just acquired a mini PC with a 10" screen and when I run Power SDR part of
the PSDR window is not shown on the screen. I looked in the KB and found the
article, but it relates to an older O/S.

I am using Windows 7 32bit with a screen resolution of 1280 X 1024 and the
display fonts set to "Smaller".

Is there anything else I can adjust to get the entire PSDR to show on the
screen? I'd like to keep the small monitor if possible.

Paul Delaney - K6HR
paul.hamra...@verizon.net
http://k6hr.dyndns.org:8080 



___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

[Flexradio] WPX Contest

[Paul Delaney - K6HR]

In the recent WPX Contest I decided to try a different approach than I used
the last time. I switched the Panadapter to 2x zoom level and went up and
down the bands looking for the weakest signals I could find. They were easy
to see at 50fps. It is truly amazing what the 5000 can hear! These were all
stations that were down at the noise level, many with strong adjacent QRM. I
was able to eliminate strong nearby stations easily by grabbing the edge of
the passband and dragging with the mouse - bye bye QRM.

Talk about tuning in excitement...

I worked 145 of these weak signals worldwide!

Paul Delaney - K6HR
paul.hamra...@verizon.net
http://k6hr.dyndns.org:8080 



___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

Re: [Flexradio] Looking for istep by step instructions

[Paul Delaney - K6HR]

Instructions can be found on the Flex website using the search feature.
  - Original Message - 
  From: Robin Haighton 
  To: flexradio@flex-radio.biz 
  Sent: Sunday, March 13, 2011 12:12 PM
  Subject: [Flexradio] Looking for istep by step instructions


  Having lost my hard drive, I am looking for step by step instructions on how
  to re-install MIXw using Com0Com, VAC, CAT etc. on my 5K

  Can anyone help? Is ther a KB with details?

  VE3FRH -Robin

  ___
  FlexRadio Systems Mailing List
  FlexRadio@flex-radio.biz
  http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
  Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
  Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/
___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

Re: [Flexradio] [Commercial] New member in the Abroham Neal family!

[Paul Delaney - K6HR]

WOW! And I thought my Passmark score of 2022 was good!

Paul Delaney - K6HR
paul.hamra...@verizon.net
http://k6hr.dyndns.org:8080 

-Original Message-
From: flexradio-boun...@flex-radio.biz
[mailto:flexradio-boun...@flex-radio.biz] On Behalf Of Neal Campbell
Sent: Sunday, January 09, 2011 9:54 AM
To: flexradio@flex-radio.biz
Subject: [Flexradio] [Commercial] New member in the Abroham Neal family!

Hi all

This is a commercial announcement so please delete it if you are not
interested (and sri about using your bandwidth)!

I am happy to announce the new member in the SDR systems that Abroham Neal
Software sells and it is truly the best one I have ever seen. You can see
the Passmark, DPCLat and Windows Experience Index scores in this screenshot
http://www.abrohamnealsoftware.com/MyLittleFriend.PNG

The DPClat score shows 0us and while thats amazingg, I do want to confess I
have seen it spike as high as 212us when I was running the Passmark System
Benchmark test, but otherwise it appears that 17us is the previously high
spike I have witnessed before that.

The system shown in the benchmark results is a bit different that the new
Premium system in 3 ways: 1., its using an Intel i7-920 processor while the
new Premium System is using an Intel i7-950;  2. it is using the new OCZ
Revo 120GB PCIe solid state drive which bypasses SATA interfaces and talks
directly over the PCIe bus; and,  3 it has an AMD HD5770 card as opposed to
the higher rated HD6850 card in the premium system.  I will be offering Revo
SSD as an upgrade on the new Premium System (+$100) when I feel comfortable
its completely reliable.

The new Premium computer consists of:
- Intel i7-950 CPU
- Asrock x58 Extreme 3 motherboard
- 12GB of triple channel DDR3 1600 memory
- 120GB Sata II solid state drive
- 1TB Sata III hard disk drive
- Blu-ray/DVD/CD burner/reader
- AMD HD 6850 graphics controller
- Ultra-quiet Antec Sonata Elite case
- Granite Digital Fire-VUE premium cable.

This seriously is as close to 0 microsecond latency as I have seen.

Its another example that Asrock motherboards appear the best engineered
boards for very low latency windows system. They are now the supplier of all
3 desktop models I sell.

I also have a couple of used laptops, in case you are in the market. I have
a 6 month old version of the premium laptop I sell, with the same warranty
as the new model. I have a Core 2 Duo laptop that is less perfect for SDR
work (but acceptable) and great for regular usage. Both are 17" screens and
show some wear and tear. If interested, let me know.

Thanks as always for your tolerance of these notes as well as the support
you have given me!
73
Neal Campbell
Abroham Neal Software
www.abrohamnealsoftware.com
(540) 645 5394
___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage:
http://www.flexradio.com/


___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

Re: [Flexradio] fldigi test message sites?

[Paul Delaney - K6HR]

This link has 'Sights And Sounds':

http://www.w1hkj.com/FldigiHelp-3.12/Modes/index.htm


Paul Delaney - K6HR
paul.hamra...@verizon.net
http://k6hr.dyndns.org:8080 

-Original Message-
From: flexradio-boun...@flex-radio.biz
[mailto:flexradio-boun...@flex-radio.biz] On Behalf Of Gary Warner
Sent: Wednesday, January 05, 2011 4:57 PM
To: supp...@flex-radio.com
Cc: flexradio@flex-radio.biz
Subject: Re: [Flexradio] fldigi test message sites?

Dudley,

Thanks.  It has good sounds, but no images (at least as far as I can see).

Rick Bischoff (K7ET) suggested 
http://www.nonstopsystems.com/radio/radio-sounds.html , which has both 
good images and good sounds.

Gary
WG1I




___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

Re: [Flexradio] Best Transverters?

[Paul Delaney - K6HR]

I was hoping external transverters might be more 'economical'.
It's pretty clear the 5kVU upgrade is the best way.
Thanks to all who replied.

Paul Delaney - K6HR
paul.hamra...@verizon.net
http://k6hr.dyndns.org:8080 

-Original Message-
From: flexradio-boun...@flex-radio.biz
[mailto:flexradio-boun...@flex-radio.biz] On Behalf Of William H. Fite
Sent: Tuesday, December 28, 2010 7:28 AM
To: t...@wb8cox.com
Cc: flexradio@flex-radio.biz
Subject: Re: [Flexradio] Best Transverters?

Anyone familiar with this one??

http://www.kuhne-electronic.de/en/products/transverter/tr-144-h-40.html




___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

[Flexradio] Best Transverters?

[Paul Delaney - K6HR]

I'm considering purchasing 2m/440 transverters for use with my 5000A.
Can anyone make a recommendation?

Paul Delaney - K6HR
paul.hamra...@verizon.net
http://k6hr.dyndns.org:8080 


___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

Re: [Flexradio] Which Antenna?

[Paul Delaney - K6HR]

Check out the Mosley TA-33JR-WARC
  - Original Message - 
  From: Drax Felton 
  To: flexradio@flex-radio.biz 
  Sent: Tuesday, November 16, 2010 7:02 PM
  Subject: Re: [Flexradio] Which Antenna?



  I use a software defined antenna.

  Just kidding. But, which antenna is best a loaded question that many hams
  will debate and chastise each other for ever over never reaching a
  consensus.

  Start reading and find what fits in your yard that you can afford, what your
  neighbors and XYL will put up with.




  -Original Message-
  From: flexradio-boun...@flex-radio.biz
  [mailto:flexradio-boun...@flex-radio.biz] On Behalf Of Burt
  Sent: Tuesday, November 16, 2010 9:09 PM
  To: flexradio@flex-radio.biz
  Subject: Re: [Flexradio] Which Antenna?

  I am thinking the RF that comes out of a Flex is similiar to the RF that
  comes out of every other rig or is there something special about it that
  requires a FLEXiable antenna?
  Burt



  ___
  FlexRadio Systems Mailing List
  FlexRadio@flex-radio.biz
  http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
  Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
  Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/
___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

Re: [Flexradio] CAT Delay Between HRD V5 and PSDR 2.0.8

[Paul Delaney - K6HR]

Thanks for the fast replies!
I don't use DM780 or the HRD logbook, but use HRD as a tuning interface for 
PSDR.

I have reverted back to PSDR 2.0 for the time being.

Paul Delaney
paul.hamra...@verizon.net
http://k6hr.dyndns.org:8080

- Original Message - 
From: "Ed Wilson" 

To: "rich kennedy" ; 
Sent: Friday, September 24, 2010 9:50 AM
Subject: Re: [Flexradio] CAT Delay Between HRD V5 and PSDR 2.0.8



Paul,

I would be pleased to help as well if you contact me off list. I use DM780 
and
the logging program (without HRD) successfully with a Flex-5000 and a 
Flex-3000,
the 5K running under Windows 7 and the 3K under Windows XP. I also 
sometimes use
DM780 with my IC-7700, but I am now almost a 100% Flex convert (the 
IC-7700 to

sound card cables have been pulled)!

Ed, K0KC





From: rich kennedy 
To: flexradio@flex-radio.biz
Sent: Fri, September 24, 2010 12:27:47 PM
Subject: [Flexradio] CAT Delay Between HRD V5 and PSDR 2.0.8

Paul,
Don, KD6HQ is correct that delay problems have been documented between HRD
(actually DM780 which is one of several modules) and PSDR; you can search 
for
these discussions and the reconciliations in order to get these two 
packages
correctly (v little delay) communicating.  I wouldn't ditch HRD just 
because you


weren't initially successful - many of us (W5XZ, K0KC, etc.) have gone 
through
the same growing pains.  HRD&DM780 are, IMHO, an excellent combination and 
I've
successfully used them in both RTTY and PSK, for DX'ing and contesting, 
If you

still need assistance, please contact me off-line.  73, Rich K3VAT


.
Message: 10
Date: Thu, 23 Sep 2010  21:00:55 -0700
From: "Don" 
To: "Flex Radio" 
Subject: [Flexradio] [FlexRadio] CAT Delay Between HRD V5 and PSDR
   2.0.8
Message-ID: 
Content-Type: text/plain;charset="iso-8859-1"

Paul

This problem has been discussed before so if you do a "search" you should 
find

some more information.

I do use HDR in a manor of speaking.   Actually what I use is DM-780 and 
the Log


Book and PowerSDR

to control the Flex.

In order for the log book to use the "Auto" logging functions you must 
connect

DM-780 to the log book.
This is normally done thru the main HDR program.  An alternative is to use 
a

program called  Mini-Deluxe.
Mini-Deluxe allows DM-780 and Log Book to talk to each other without the 
need to


load HDR.


See:  http://www.vhfwiki.com/minideluxe

For me this virtually elimated the delay.  I don't even open up HDR, I 
just open


Mini Deluxe and then DM-780 and the log book.

Good luck

Don


Message: 7
Date: Thu, 23 Sep 2010 19:30:22 -0700
From: "Paul Delaney - K6HR" 
To: 
Subject: [Flexradio] CAT Delay Between HRD v5 and PSDR 2.0.8
Message-ID: 
Content-Type: text/plain; format=flowed; charset=iso-8859-1;
   reply-type=original

Has anyone else experienced the  significant delay (several seconds) 
between

PSDR 2.0.8 and HRD?
I hadn't had this problem before switching to 2.0.8 today.
Before I switch back does anyone have a suggestion of what I might look 
at?


Paul Delaney
paul.hamra...@verizon.net
http://k6hr.dyndns.org:8080/



___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: 
http://www.flexradio.com/





___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: 
http://www.flexradio.com/ 



___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

[Flexradio] CAT Delay Between HRD v5 and PSDR 2.0.8

[Paul Delaney - K6HR]

Has anyone else experienced the significant delay (several seconds) between 
PSDR 2.0.8 and HRD?

I hadn't had this problem before switching to 2.0.8 today.
Before I switch back does anyone have a suggestion of what I might look at?

Paul Delaney
paul.hamra...@verizon.net
http://k6hr.dyndns.org:8080 



___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

[Flexradio] PSDR 2.08 with 1500

[Paul Delaney - K6HR]

I'm using 2.08 with my new 1500 and notice there is no SWR on the TX meter 
menu.

I'm guessing this is unique to the 1500.
Before I switch my 5000 to 2.08 am I correct that the SWR menu item will 
appear when using the 5000?


Paul Delaney
paul.hamra...@verizon.net
http://k6hr.dyndns.org:8080 



___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

[Flexradio] Flex 1500 Excitement!

[Paul Delaney - K6HR]

I received my 1500 yesterday and I must admit I am very pleasantly 
surprised.
My concern was the RX sensitivity and how it would compare to what I am used 
to with my 5000A. While it's obviously not 5000 RX it certainly is 
impressive. A lot of bang out of this little box!


Paul Delaney
paul.hamra...@verizon.net
http://k6hr.dyndns.org:8080 



___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

[Flexradio] Are Flex Offices Closed today?

[Paul Delaney - K6HR]

Nobody answering phones today?

Paul Delaney


___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flexradio.com/  Homepage: http://www.flexradio.com/

[Flexradio] SDR Overkill ?

[Paul Delaney - K6HR]

Is this just overkill for running Flex SDR'?

http://k6hr.dyndns.org:8080/others/skulltrail2.jpg

http://k6hr.dyndns.org:8080/others/skulltrail3.jpg


Paul Delaney - K6HR
F5K PSDR 2.0 BETA
WINDOWS 7 64 X25 SSD
DP55WG i7 875k 4G DDR3 
http://k6hr.dyndns.org:8080





___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flex-radio.com/  Homepage: http://www.flex-radio.com/

Re: [Flexradio] SSD for me?

[Paul Delaney - K6HR]

I use SSD's in my machines. Great increase in speed for windows. My Windows
7 machines boots in about 25 seconds! Programs load lightning fast!

I agree with Tim. An SSD doesn't really enhance PSDR just the speed of
Windows in certain aspects.

Paul Delaney - K6HR
F5K PSDR 2.0 BETA
WINDOWS 7 64 X25 SSD
DP55WG i7 875k 4G DDR3 
http://k6hr.dyndns.org:8080


-Original Message-
From: flexradio-boun...@flex-radio.biz
[mailto:flexradio-boun...@flex-radio.biz] On Behalf Of dan edwards
Sent: Friday, July 02, 2010 7:38 AM
To: flex list
Subject: [Flexradio] SSD for me?

K5LC, local bud, is raving about how fast win7 is with a 60 gig ssd.
 any flexers using one, and noticing performance enhancements?
73, w5xz, dan
___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flex-radio.com/  Homepage:
http://www.flex-radio.com/


___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flex-radio.com/  Homepage: http://www.flex-radio.com/

[Flexradio] FW: Two Instances Of PSDR

[Paul Delaney - K6HR]

 

 

 

Is it possible to have two instances of PSDR running on one PC with two
radios? 5000/3000

___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flex-radio.com/  Homepage: http://www.flex-radio.com/

Re: [Flexradio] virtual com port splitter

[Paul Delaney - K6HR]

If you don't want it running all the time, you can also start it from within 
HRD from the "Programs" button.


K6HR


- Original Message - 
From: "Laurie" 

To: 
Sent: Monday, April 12, 2010 7:13 PM
Subject: [Flexradio] virtual com port splitter



I came across a programme that is a Virtual Serial Port Emulator.

In it, is the ability to create a com port splitter which enables up to 8
programmes to run off one singal virtual com port.

It works a treat as I tried it with HRD, DM780, N1MM, CWskimmer all 
running

at once and all having rig control.

Its downside is the fact that is what the name suggests, an emulator and
therefore having to start it every time the computer starts and then open
the saved file.

What I would like to know, is there a programme out there that the does 
the

same but you don't have to start it every time you start the computer, in
otherwords like VSP,com0com with built in splitter facilty?

Thanks

Laurie

___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flex-radio.com/  Homepage: 
http://www.flex-radio.com/ 



___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flex-radio.com/  Homepage: http://www.flex-radio.com/

[Flexradio] Mouse Wheel in Windows 7

[Paul Delaney - K6HR]

My mouse wheel no longer tunes in the PSDR panadapter now that I have 
installed Windows 7. Is there a setting that I'm missing? I've gone through 
everything in the setup menu and have not found the problem yet.



Paul Delaney - K6HR
paul.hamra...@verizon.net
http://k6hr,dyndns.org:8080 



___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flex-radio.com/  Homepage: http://www.flex-radio.com/
Message delivered to arch...@mail-archive.com

[Flexradio] VAC Under Windows 7

[Paul Delaney - K6HR]

I have my Flex 5000 and PSDR working but can't get VAC working yet.
Can anyone give me a hint how to get VAC working in W7 64bit as an unsigned 
driver?


Paul Delaney
paul.hamra...@verizon.net
http://k6hr.dyndns.org:8080 



___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flex-radio.com/  Homepage: http://www.flex-radio.com/
Message delivered to arch...@mail-archive.com

Re: [Flexradio] Audio Interface

[Paul Delaney - K6HR]

Hey Joe,

I use a small 6 channel audio mixer here to do the same thing.
Works great!

- Original Message - 
From: "Joe Camilli" 

To: "Flexradio" 
Sent: Monday, January 11, 2010 6:36 AM
Subject: [Flexradio] Audio Interface


I am posting this here because many Flexers have experience with external
sound interfaces – due to the early Flex radio. So here is a description of
my current sources of audio:

Flex-3000 – HF radio

Icom 2200H – 2M radio

Yeasu  FT-60 – 2/440 radio

RS Pro 97 – scanner

Computer



All except the computer are mono audio sources.



The goal is to make the computer an audio hub thus allowing me the ability
to control the volume of each audio source through one set of speakers
attached to the computer. I was looking at the Delta 44 or the Delta 1010LT
interface. I would like to get some feedback on this approach, would it have
an impact on the Flex-3000 since this computer also runs PSDR.
___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flex-radio.com/  Homepage: 
http://www.flex-radio.com/
Message delivered to paul.hamra...@verizon.net 




___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flex-radio.com/  Homepage: http://www.flex-radio.com/
Message delivered to arch...@mail-archive.com

Re: [Flexradio] PSDR & MMSSTV

[Paul Delaney - K6HR]

Try this from Bret:

Yep, you want to use VAC (registered version) and there is a file you have
to add to the MMSSTV directory called "sc_select.mmw" that lets you select
the VAC sound card devices and you need to run the Virtual serial port
program my recommendation is VSP Manager by K5FR for the PTT serial port.
If you already have other software control programs running then the only
thing you should need is the "sc_select.mmw" file.
73's and if you need more help let me know or can't find the sc_select file
I can send it to you.
Bret
WX7Y




- Original Message - 
From: "William MacCracken" 

To: 
Sent: Monday, January 04, 2010 1:14 PM
Subject: [Flexradio] PSDR & MMSSTV



Is anyone using MMSSTV
with PowerSDR?  I
have it working but I have to switch to Device ID 2 to
transmit (within MMSSTV: Option -> Setup MMSSTV -> Misc -> Device ID).
After tx I have to switch back to ID 1 for rx.

The Device IDs number -1 to 3.  -1 and 0 can receive without VAC.  1 can
receive with VAC.  Only 2 can transmit but it does not receive.  3 results
in "Cannot open Sound Card 3".

The problem, in a nutshell, is the need to always go through the menu to
switch back and forth.  Is there a way around this in MMSSTV?

Thanks
___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flex-radio.com/  Homepage: 
http://www.flex-radio.com/
Message delivered to paul.hamra...@verizon.net 



___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flex-radio.com/  Homepage: http://www.flex-radio.com/
Message delivered to arch...@mail-archive.com

Re: [Flexradio] what is cpdr do ?

[Paul Delaney - K6HR]

A simple Knowledge Center search on the word "compander" reveals this:

Transmit Compander
PowerSDR uses audio compression to make quite sounds louder-the difference, 
in decibels, between the loudest and the quietest portion of the audio 
input, i.e., its dynamic range. There's a down side also, it can make 
unwanted sounds, like breath sounds, also louder. More is not necessarily 
better. A good starting point is 3 db. Rarely will one need to increase 
compression above 10 db. If you're a soft spoken person, consider operating 
with the Compander on all the time.  Companding is also very effective on 
AM. The choice of microphone will play heavily in the compressor settings.


The compander is used to overcome limited dynamic range in one portion of an 
audio system. In amateur radio applications this is typically the high 
frequency response. The compander is both a compressor and a high frequency 
expander.   An ideal setting for the compander is level 3.


There is a DX version of the Compander which has a higher compression ratio 
for more "punch", such as trying to bust a DX pileup.



HTH

- Original Message - 
From: "elan paim" 

To: 
Sent: Monday, January 04, 2010 1:00 PM
Subject: [Flexradio] what is cpdr do ?



is any one can tell me what the cpdr do and how it work ?
thank you


E.P
___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flex-radio.com/  Homepage: 
http://www.flex-radio.com/
Message delivered to paul.hamra...@verizon.net 



___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flex-radio.com/  Homepage: http://www.flex-radio.com/
Message delivered to arch...@mail-archive.com

Re: [Flexradio] [FlexEdge] crackly audio

[Paul Delaney - K6HR]

I observe the same here. I only experience the crackly audio after a DPC 
spike and sometimes the crackly audio is accompanied by a 'bouncing' 
panadapter display. Toggling PSDR start button cures the problem here. 
QX9650 cpu 2gb RAM PSDR running in "Normal" mode. 2048/192


Paul Delaney - K6HR


- Original Message - 
From: "Alan NV8A" 




On 01/03/10 11:40 am, Michael Jones wrote:

This is a new quad core i7 machine, the CPU utilization never gets up 
more than maybe 10% or so.
The more I've played with it the more I believe what I am seeing is a 
Skimmer audio issue, not a PSDR issue.

It only happens when using Skimmer, never just with PSDR.


Mine is an older far less powerful machine, and I get the crackling from 
time to time, especially after something has caused a DPC spike.


I'm not using CW Skimmer.

73

Alan NV8A

___
Flexedge mailing list
flexe...@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexedge_flex-radio.biz
This is the FlexRadio Systems e-mail Reflector called FlexEdge.  It is 
used for posting topics related to SDR software development and 
experimentalist who are using alpha and beta versions of the software. 



___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flex-radio.com/  Homepage: http://www.flex-radio.com/
Message delivered to arch...@mail-archive.com

Re: [Flexradio] DM780 CAT response time

[Paul Delaney - K6HR]

Thanks Larry, I got it! You're not kidding, tuning is considerably faster!
I use HRD to tune my 5000. Used to be quite a long delay when I dragged the 
tuning slider across the band. It has improved a lot!

Thanks for the link!

Paul Delaney - K6HR

- Original Message - 
From: "Larry da Ponte" 



Afirmative - there is talk on the HRD forum about the website issue.  Here
is a direct link to 2434:

http://mannindustries.net/hrd/HRD5.0...b2434_Full.exe<http://mannindustries.net/hrd/HRD5.0Beta/HRDv050b2434_Full.exe>

On Sat, Jan 2, 2010 at 9:56 PM, Paul Delaney - K6HR <
paul.hamra...@verizon.net> wrote:



Seems the HRD webpage is currently malfunctioning

Paul Delaney K6HR



___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flex-radio.com/  Homepage: http://www.flex-radio.com/
Message delivered to arch...@mail-archive.com

Re: [Flexradio] DM780 CAT response time

[Paul Delaney - K6HR]

Seems the HRD webpage is currently malfunctioning

Paul Delaney 
K6HR


- Original Message - 
From: "David Beumer W0DHB" 

To: "flex" 
Sent: Saturday, January 02, 2010 2:42 PM
Subject: [Flexradio] DM780 CAT response time



FYI

DM780 v5.0 beta build 2434  seems to have improved the CAT frequency 
tuning response time.

PTT through CAT still slow.

Dave W0DHB



___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flex-radio.com/  Homepage: http://www.flex-radio.com/
Message delivered to arch...@mail-archive.com

Re: [Flexradio] Wait for 2.0?

[Paul Delaney - K6HR]

I'll say it has improved!

The new Firewire driver allows me to run in "Normal Mode" and it is very 
stable. While using the previous driver I would experience freeze ups when 
operating in Normal Mode and resorted to Safe Mode 1.


Paul Delaney - K6HR

- Original Message - 
From: "Tim Ellison" 


This is a new Firewire driver and it is 100% compatible with PowerSDR 
v1.18.3 and the latest firmware.  There are some stability and performance 
improvements in the new Firewire driver along with a utility to check out 
the Firewire card to see if it is 100% compatible with the FLEX Firewire 
driver.




___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flex-radio.com/  Homepage: http://www.flex-radio.com/
Message delivered to arch...@mail-archive.com

Re: [Flexradio] MMSSTV

[Paul Delaney - K6HR]

Thanks Bret!
I was resigned to the fact that MMSSTV would not work with VAC.
Testing shows it is working perfectly now!

Check out my SSTV webpage now using the Flex 5000a:

http://k6hr.dyndns.org:8080/wwsstv.html

Paul Delaney
K6HR



- Original Message - 
From: "Bret Mills" 

To: "'Paul Delaney - K6HR'" 
Sent: Monday, December 07, 2009 1:58 PM
Subject: RE: [Flexradio] MMSSTV


Hi Paul one more note for the best slant adjustment for the Flex. set in 
the

MMSSTV, option, setup MMSSTV, MISC setup tab, set the "clock" rate too
12000.00 Hz it will save you a bunch of time trying to get it right.

73's
Bret
WX7Y



___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flex-radio.com/  Homepage: http://www.flex-radio.com/
Message delivered to arch...@mail-archive.com

Re: [Flexradio] MMSSTV

[Paul Delaney - K6HR]

Many Thanks!
I was unable to get this working before hearing about the sc_select widget.
I now have MMSSTV working with my F5K!

Paul Delaney
K6HR

- Original Message - 
From: "Bret Mills" 

To: "'Leon Bishop'" ; 
Sent: Monday, December 07, 2009 11:18 AM
Subject: Re: [Flexradio] MMSSTV


Here is the location were you can see how to set up sc_select and down 
load

the file  http://mmhamsoft.amateur-radio.ca/sc_select/index.htm


Yep, you want to use VAC (registered version) and there is a file you have
to add to the MMSSTV directory called "sc_select.mmw" that lets you select
the VAC sound card devices and you need to run the Virtual serial port
program my recommendation is VSP Manager by K5FR for the PTT serial port.
If you already have other software control programs running then the only
thing you should need is the "sc_select.mmw" file.
73's and if you need more help let me know or can't find the sc_select 
file

I can send it to you.
Bret
WX7Y
-Original Message-
From: flexradio-boun...@flex-radio.biz
[mailto:flexradio-boun...@flex-radio.biz] On Behalf Of Leon Bishop
Sent: Monday, December 07, 2009 11:09 AM
To: FlexRadio@flex-radio.biz
Subject: [Flexradio] MMSSTV

Anyone using mmsstv with a F5K and VAC? If so send me directions off list.

Thanks,

Leon N5PU



n...@cableone.net

___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flex-radio.com/  Homepage:
http://www.flex-radio.com/ Message delivered to bmil...@ecso.com



___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flex-radio.com/  Homepage: 
http://www.flex-radio.com/
Message delivered to paul.hamra...@verizon.net 



___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flex-radio.com/  Homepage: http://www.flex-radio.com/
Message delivered to arch...@mail-archive.com

[Flexradio] What is Hot Wheels?

[Paul Delaney - K6HR]

Someone mentioned "Hot Wheels" for use with tuning in PSDR
What is Hot Wheels and where would one find it?

Paul Delaney
paul.hamra...@verizon.net
k...@k6hr.ampr.org
http://k6hr.dyndns.org:8080

___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flex-radio.com/  Homepage: http://www.flex-radio.com/
Message delivered to arch...@mail-archive.com

Re: [Flexradio] RF in USB Optical Mouse

[Paul Delaney - K6HR]

Purchased a wireless mouse this afternoon...QRO!
Thanks for all the suggestions!

Paul Delaney
K6HR

- Original Message - 
From: "Dudley Hurry" 

To: "Paul Delaney - K6HR" 
Cc: 
Sent: Sunday, November 22, 2009 4:18 PM
Subject: Re: [Flexradio] RF in USB Optical Mouse



Paul,

Have you tried a clamp on ferrite (or choke)  just right at the USB 
port?   Be sure to run the cable through the choke several times,  this 
will increase the efficiency with each turn through. 


73,
Dudley

WA5QPZ



Paul Delaney - K6HR wrote:


My shack has one RFI problem. I am getting RF in the mouse and it 
shuts off. The only fix is to unplug it, plug it back in. I've tried 
just about everything I can think of. Does anyone know of a well 
shielded mouse I can purchase, or have any other suggestions? If 
anyone has had this problem and resolved it, I'd love to know how you 
did it!


Paul Delaney
K6HR

___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flex-radio.com/  Homepage: 
http://www.flex-radio.com/

Message delivered to jhu...@austin.rr.com



___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flex-radio.com/  Homepage: http://www.flex-radio.com/
Message delivered to arch...@mail-archive.com

[Flexradio] RF in USB Optical Mouse

[Paul Delaney - K6HR]

My shack has one RFI problem. I am getting RF in the mouse and it shuts off. 
The only fix is to unplug it, plug it back in. I've tried just about 
everything I can think of. Does anyone know of a well shielded mouse I can 
purchase, or have any other suggestions? If anyone has had this problem and 
resolved it, I'd love to know how you did it!


Paul Delaney
K6HR 



___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/
Knowledge Base: http://kc.flex-radio.com/  Homepage: http://www.flex-radio.com/
Message delivered to arch...@mail-archive.com